Cobra 4627 User manual

4625 - 4627 CAN/PLIP
INSTALLATION MANUAL

INSTALLATION MANUAL 4625 - 4627 CAN/PLIP 2
Summary
1. KIT CONTENTS............................................................................................................................................................3
2. INTRODUCTION & INSTALLATION METHODOLOGY (how to access to the vehicle specific technical documents,
Data Linker tool, Antares software, how to define the installation solution).......................................................................3
3. SYSTEM’S CONFIGURATION......................................................................................................................................4
4. HOW TO PREPARE PIN CODE CARD ........................................................................................................................5
5. INSTALLATION PROCEDURE (system’s component locations, electrical connections)..............................................5
6. ACTIVE FUNCTIONALITIES (descriptions)..................................................................................................................8
- ELECTRIC DIAGRAMS
7. PROGRAMMABLE FUNCTIONS (see the “Functions programming tables” manual).........................................13
8. HOW TO PROGRAM FUNCTIONALITIES, COBRA REMOTE CONTROLS AND DRIVER CARDS SELF
LEARNING PROCEDURE (see ‘PAGE 1’ and ‘PAGE 2’ of the “Functions programming tables” manual)............13
9. FUNCTIONAL TEST....................................................................................................................................................14
10. CAN INDEX MANUAL SELECTION..........................................................................................................................14
11. SELF LEARNING PROCEDURE REQUIRED TO REPLACE THE MAIN UNIT OR THE WIRELESS SIREN
REPLACEMENT..............................................................................................................................................................14
12. DOCUMENTS HANDOVER......................................................................................................................................15
13. TECHNICAL FEATURES ..........................................................................................................................................15
14. UK MARKET..............................................................................................................................................................15

INSTALLATION MANUAL 4625 - 4627 CAN/PLIP 3
1. - KIT CONTENTS.
The following are the main parts supplied in the kit:
- Main alarm unit.
- Wireless back-up battery siren or wired siren, loudspeaker.
- Main unit universal wiring harness.
- Siren wiring harness.
- Siren bracket.
- Ultrasonic sensors.
- Installation accessories.
- LED / control button.
- Quick reference user manual.
- Pin Code card.
2. - INTRODUCTION.
The main unit of this system is equipped with an on board CAN interface (Controller Area Network) that allows the data
readingfromthe vehicle CAN network. In can also be installedconfigured as PLIP, withthissolution the unit is not connected
to the CAN network, but to the central door locking motors, to the door locking switches and/or to the direction lights.
It can be armed/disarmed by the vehicle original remote control, with the Cobra one or with the Driver Card (optional).
This manual contains all information required to fit the system on 12V battery vehicles with the negative pole connected
to the vehicle body.
HOW TO ACCESS TO THE VEHICLE SPECIFIC TECHNICAL DOCUMENTS, DATA LINKER TOOL, ANTARES
SOFTWARE.
Access to the web site www.cobra-at.com > Installer area and register yourself to be allowed to download the technical
documentation.
Data Linker programming tool and the software “Antares” are required to customize the product for the destination vehicle.
DataLinkeriscomposedbyaUSBinterfacemodule,a12VDCpowersupply,aCDcontainingthesoftware“Antares” and the
requiredinstructions. Product specific wiringharness are also supplied to connect the USB moduleto the product mainunit.
Antaresallowstoconfigure/customizeandtoprogramtheCAN/PLIPsoftwareforthedestinationvehicleusing your computer.
HOW TO DEFINE THE INSTALLATION SOLUTION.
Access to the web site www.cobra-at.com > Login > user ID > password > access > professional area and, clicking on
the menu, supply all the requested destination vehicle information (in the example a VW Polo, year 2011) as the information
of the product to install, in this case the 4600 range.
VEHICLE TYPE.
Auto - Car
PRODUCT TYPE.
Antifurti auto - Car alarms
BRAND LIST.
Volkswagen
MODEL LIST.
Polo

INSTALLATION MANUAL 4625 - 4627 CAN/PLIP 4
The list on the right side of the screen shows the product families. Clicking on the link you will get the full application list
available for the destination vehicle for the product family selected. Check at first if there is a CAN application available, it
offers the best compromise amoung functionalities offered/fitting time.
If no one CAN product installation proposal is available, make the same research clicking on “PLIP alarm” range AK4600
– 4400 Plip.
If there is an installation solution clicking on the vehicle model you can download the vehicle specific installation sheet.
IfnooneCAN and no one Plip installation proposal is available, choose again the vehicletypethen,as“Product type” select
“Application manuals”.The list on the right sideofthescreenshows the application manuals available, click on “Application
manuals” to get the application manual list, then download the installation manual of the 4600 for the Plip configuration.
3. - SYSTEM’S CONFIGURATION.
Be sure to have connected all Data Linker components and to have power supplied the system.
Run Antares.
As soon as Antares is starting, it automatically checks - if the computer is connected to internet - if the installed version is
the most updated one and, if not, it proposes its update.
We recommend to download all times the last update.
Proceed as follow:
A. Select the language.
B. Select “alarm and modules”.
C. Select product “4600 “ as “1 wire” or “2 wire”.
D. Select the procedure “firmware update”.
E. Click on “proceed”.
F. Select the vehicle brand.
G. Select the vehicle model.
H. Select the vehicle model year.
I. Click on “proceed”.
L. Confirm and continue.
M. Wait until the programming confirmation window appears.
Additional software installation and tool usage details are available on the specific manual supplied in the Data Linker kit
or in the Cobra web site, professional area, Application manuals.

INSTALLATION MANUAL 4625 - 4627 CAN/PLIP 5
4. - HOW TO PREPARE THE PIN CODE CARD.
Remove the separate PIN Code label from the back of the system main unit and place onto the supplied PIN Code Card.
www.cobra-at.com
PERSONA
IDENTIFICATION
CODE
4C4415A2A
S/N 0003 050524
PIN
CODE 1122
PIN
CODE 1122
5. - INSTALLATION PROCEDURE.
System’s component positioning.
As much as the components of the system will be placed in secure and difficult to access positions as higher the protection
level will be.
WARNING: each element must be positioned so that it does not interfere with moving parts.
Alarm unit.
Itmustbefittedinside the vehicle far away from heating sources, paying attention to keepthemainconnectororiented down.
Siren.
It can be installed in the engine bay as inside the vehicle far away from heating sources paying attention to keep the
main connector oriented down.
Ultrasonic volumetric sensor.
The ultrasonic transducers must be fixed to the top of the A pillars pointed towards the rear window or to the top of the
C pillars pointed towards the windscreen. Their orientation should be as much as possible parallel to the side windows.
Emergency LED/control button
It must be fitted on the dashboard with its LED in a in sight position. The pushbutton should be easily accessible by the
driver.
Bonnet pushbutton.
The installation of the supplied pushbutton is required if the vehicle is not yet equipped with the original one. The specific
vehicle CAN/PLIP installation sheet supplies this info.
Antennas.
The RF antennas positioning (for both the main unit and the siren) is crucial for a proper system’s performance.They must
not be cut, wrapped, connected to any other cables or to the vehicle body and they must be kept separate from the main
wiring harness and as far as possible from metallic parts.

INSTALLATION MANUAL 4625 - 4627 CAN/PLIP 6
Electrical connections.
WARNING: to prevent damage to the vehicle electrical system during installation, we recommend to
disconnect the battery negative cable and to reconnect it only after installation is completed. If the battery
is not disconnected, to avoid the possible generation of errors by the original central units of the vehicle, it
is necessary to pay attention during the connections and the use of the installation tools.
Pay attention when joining two or more wires. Avoid to make “quick connections” that do not ensure a good quality. Also
make sure that the wires of the Cobra 4625 - 4627 are routed so that they follow the original wiring of the vehicle to which
they should be joined with the raps.
The addition of fuse is required as specified in the main connection diagram.
24 ways connector J pin-out for CAN configurations
J-1 Analogic input: make the connection if required by the specific vehicle CAN installation sheet.
J-2 Analogic input: make the connection if required by the specific vehicle CAN installation sheet.
J-3 Logic blinker output: make the connection if required by the specific vehicle CAN installation sheet.
J-4 Analogic input: make the connection if required by the specific vehicle CAN installation sheet.
J-5 Analogic input:make the connection if required by the specific vehicle CAN installation sheet.
J-6 Analogic input: make the connection if required by the specific vehicle CAN installation sheet.
J-7 +15/54 connection: if the signal is not detected from the CAN network, connect this input to the ignition key on, checking
that the wire is permanently fed during the crancking phase and while the engine is running. Fit a 3A fuse as close as possible to
the vehicle connection point.
J-8 GND connection: the ground must be connected to a factory earth point or directly to the negative pole of the battery.
J-9 12V connection (+30): the positive supply must be connected to a vehicle positive connection point upstream of the fuse
box. Fit a 15Afuse as close as possible to the connection point.
J-10 Cobra bus: communication line for the connection of compatible Cobra sirens and sensors.
J-11 and J-12 CAN H/L: to connect as shown in the specific vehicle CAN installation sheet.
J-13Negative input for additional modules:tobeusedasatriggeringinputfortheconnectionofcompatibleCobramodules.
J-14 Negative output for modules: active when the system is armed. To be used for the connection of compatible Cobra
modules.
J-15 Horn/loudspeaker negative output: to program in line with the connected device. See electric diagrams and
functionalities programming tables. The output set automatically as per selected device, for horn choose also fix or intermittent.
J-16 Analogic input: to be connected to a vehicle device (ex. passenger compartment fan heater) to reduce the US sensitivity
(step 7.12*) or to be connected to a push-button for the driver recognition (step 7.18*). If the wire connection of this input is required
in the CAN application, it can not be used for the functions as in step 7.12* and 7.18*.
J-17 Negative input to enter in programming procedure/to connect bonnet pushbutton: if connected to
groundthesystem willenterintheprogrammingprocedureforallapplicationsnotabletodetect theoriginalbonnetpushbutton.Ifthe
siren is a wireless one this input must not be used for the bonnet pushbutton connections. For wired siren or loudspeaker this input
must be used for the connection of the bonnet pushbutton as indicated in the specific vehicle CAN installation sheet.
J-18 Analogic input: make the connection if required by the specific vehicle CAN installation sheet.
J-19 Logic blinker feedback input or power blinker output: make the connection if required by the specific vehicle
CAN installation sheet.
J-20 Power blinker output: make the connection if required by the specific vehicle CAN installation sheet.

POWER
LOGIC
BLINKER
BLUE
YELLOW-BLACK
PINK-WHITE
VIOLET-BLACK
GREY-BLACK
GREEN-RED
BLUE-PINK
ORANGE-BLACK
ORANGE
VIOLET ORANGE
VIOLET
GREEN
GREEN
J-21
J-22
J-12
J-11
J-18
J-16
J-5
J-4
J-7
J-2
J-6
max 20A (1 sec.)
6A cont.
HAZARD
BLINKER
OUTPUT
BLINKER
FEEDBACK
BLINKER
OUTPUT
BLINKER
OUTPUT
POWER
LOGIC
See the vehicle
fitting instructions
CAN - H
CAN - L
FIT THE
YELLOW-WHITE
WIRE IN THE
INDICATED
CONNECTOR
FREE POSITION!
YELLOW-WHITE
YELLOW-GREEN
YELLOW-WHITE
YELLOW-GREEN
J-19
J-19
15 A
GND
7,5 A
13
1
24
12 3
3
13
1
3
3
14
13
1
3
3
14
13
1
24
12 3
10
3
24
12
10
24
12 3
10
3
13
1
24
12 3
20
3
24
12
20
24
12 3
20
3
13
1
24
12 3
3
13
1
3
3
15
13
1
3
3
15
13
1
24
12 3
13
1
3
3
13
1
3
3
J-20
7,5 A
J-3
3 A
STARTER +50
BLACK
COBRA BUS
OUT MODULES
OUT HORN
PINK-BLACK
J-1
See
chapter 11
THE FUSES IN THE DIAGRAM ARE NOT SUPPLIED
CUT THE BLACK WIRE AND FIT IN THE
CONNECTOR FREE POSITIONS!
CDL COMMAND
IN MODULES
1
24
12 3
3
1
3
3
14
13
1
3
3
14
13
LED
J
BLACK
RED J-17
J-8
J-9
SEE
DIAGRAM
"F"

1N4004
3 A
BLACK
BLACK
OK
PASS
TX LED RX
J 15
J 15 J 15
E
C D
G
RED (TX)
RX
TX
RX
TX
Antenna
U.S. sensors, led panel
and antenna connections.
B
Install the jumper wire (see the catalogue)
between the Ultrasound TX and RX, if you don't
use the volumetric sensor.
A
-
-
WHITE
(RX)
Vehicle horn connection with additional relay.
87 30 86 85
Original
system Additional
relay
Original relay controlled by a negative signal.
Vehicle horn connection with negative control
signal to the original relay.
87 30 86 85
CDL connections (only for 4627)
Y
PASS
TX LED RX
Y
123
+30
+
-
15A
+30
- / +
- / +
U.S.
U.S.
BLACK
CDL COMMAND
CDL UNLOCK
CDL LOCK
1
24
12 3
24
12
13
23
24
12
23
13
1
12 3
12
24
12
24
F

J-17
J-10
3 A
RED
BLACK
BLUE
+30
Antenna
BLUE
YELLOW-BLUEYELLOW-BLUE
LED PANEL
AB
LED
Ø10 mm
BONNET PUSH-BUTTON
A
14 mm
Ø10 mm
Ø2 mm
B
Ø10 mm
See the vehicle
fitting instructions
12
3 A
RED
BLACK
+30
BLACK
BLACK
J
H
SIREN CONNECTIONS NO WIRELESS
WIRELESS SIREN CONNECTIONS
See the vehicle
fitting instructions
AB

INSTALLATION MANUAL 4625 - 4627 CAN/PLIP 11
J-21 and J-22 Engine crank inhibition: to get the maximum security level to the system connect the two wires as shown
in the electrical diagrams to prevent the engine starter running. During the cranking phase, measure the value of the current in the
circuit that has been interrupt, to make sure that it does not exceed the technical specifications of the product. Install an additional
relay if required.
J-23 CDL lock negative output (only for 4627): low power control signal to lock central door locking.Activated by the
Cobra remote control (optional) - (see electrical diagram F).
J-24 CDL unlock negative output (only for 4627): low power control signal to unlock central door locking.Activated by
the Cobra remote control (optional) - (see electrical diagram F).
*See the “FUNCTIONS PROGRAMMING TABLES” manual.
24 ways connector J pin-out for PLIP configurations
J-1 Positive perimetric input:to be connected to the vehicle roof lamp.
J-2 Negative perimetric input:to be connected to the vehicle roof lamp.
J-3 Logic blinker output:make the connection if required by the specific vehicle PLIP installation sheet.
J-4 Positive input for CDL motor opening signal:toconnectas indicatedin the specific vehicle PLIPinstallationsheet
or in the product installation guide for PLIP applications available on the web underApplication manuals.
J-5 Negative input for CDL opening switch signal:toconnectasindicatedinthespecificvehiclePLIPinstallationsheet
or in the product installation guide for PLIP applications available on the web underApplication manuals.
J-6 Negative input for CDL closing switch signal:toconnectasindicatedinthespecificvehiclePLIPinstallationsheet
or in the product installation guide for PLIP applications available on the web underApplication manuals.
J-7 +15/54 connection:tobe connected to a ignition key ON positive signal. The positive signal must be feeded while starting
the vehicle and when the engine is ON.
J-8 GND connection: the ground must be connected to a factory earth point or directly to the negative pole of the battery.
J-9 12V connection (+30): the positive supply must be connected to a vehicle positive connection point upstream of the fuse
box. Fit a 15Afuse as close as possible to the connection point.
J-10 Cobra BUS: communication line for the connection of compatible Cobra sirens and sensors.
J-11 and J-12 Do not connect.
J-13Negative input for additional modules:tobeusedasatriggeringinputfortheconnectionofcompatibleCobramodules.
J-14 Negative output for modules: active when the system is armed. To be used for the connection of compatible Cobra
modules.
J-15 Horn/loudspeaker negative output: to program in line with the connected device. See electric diagrams and
functionalities programming tables. The output set automatically as per selected device, for horn choose also fix or intermittent.
J-16 Blinker inhibition positive input:toconnectasindicatedinthespecificvehiclePLIPinstallationsheetorintheproduct
installation guide for PLIP applications available on the web underApplication manuals.
J-17 Negative input to enter in programming procedure/to connect bonnet pushbutton: if connected to
groundthesystem willenterintheprogrammingprocedureforallapplicationsnotabletodetect theoriginalbonnetpushbutton.Ifthe
siren is a wireless one this input must not be used for the bonnet pushbutton connections. For wired siren or loudspeaker this input
must be used for the connection of the bonnet pushbutton as indicated in the specific vehicle PLIP installation sheet.
J-18 Positive input for CDL motor closing signal:to connectasindicatedinthe specific vehiclePLIPinstallationsheet
or in the product installation guide for PLIP applications available on the web underApplication manuals.
J-19 Logic blinker feedback input or power blinker output:make the connection if required by the specific vehicle
PLIP installation sheet.
J-20 Power blinker output: make the connection if required by the specific vehicle PLIP installation sheet.

INSTALLATION MANUAL 4625 - 4627 CAN/PLIP 12
J-21 and J-22 Engine crank inhibition: to get the maximum security level to the system connect the two wires as shown
in the electrical diagrams to prevent the engine starter running. During the cranking phase, measure the value of the current in the
circuit that has been interrupt, to make sure that it does not exceed the technical specifications of the product. Install an additional
relay if required.
J-23 CDL lock negative output (only for 4627):low power control signal to lock central door locking.Activated by the
Cobra remote control (optional) - (see electrical diagram F).
J-24 CDL unlock negative output (only for 4627):low power control signal to unlock central door locking.Activated by
the Cobra remote control (optional) - (see electrical diagram F).
MAKE CONNECTIONS AS FOR ELECTRIC DIAGRAMS
6. - ACTIVE FUNCTIONALITIES.
6.1 - Interior protection with ultrasonic volumetric sensor.
The system protects the vehicle interior with a volumetric ultrasonic sensor. Any attempt to get into the vehicle will be
detected and the alarm will trigger.
6.2 - Perimetric protection with door open warning diagnostic.
Thealarm will trigger by opening any door,boot andbonnet.Should you have left any door openedwhilearming, the system
will signal it by 3 flashes of the direction lights and 3 audible signals (5 audible signals if the arming/disarming audible
signals function has been activated).
6.3 - Cable cutting protection (only for systems with back-up battery siren).
The alarm will trigger if the system is not power supplied (cutting of cables - battery disconnection) signalling the sabotage.
6.4 - Engine crank inhibition.
As soon as the system is armed the engine cranking is not possible anymore.
6.5 - Arming the system with the volumetric ultrasonic protection disabled.
This function allows to arm the system leaving temporarily disconnected the interior volumetric protection. The protection
must be disabled any time you leave somebody or an animal in the vehicle. If you want to leave any window opened also
disable the protection to avoid false alarms. All other protections remain active.
To disable the volumetric protection proceed as follow:
switchthe engine offbeing sure that the ignition switch hasbeen turned to the OFF position.Within 5 s press the emergency
panel pushbutton and keep it pressed until it will flash once to confirm only the volumetric protection has been disabled.
By keeping the pushbutton pressed the system will confirm with two flashes that only the additional sensor input has been
disabled, with three flashes for both of them disabled. The selected protection will remain disabled until the system will be
disarmed. It will be automatically restored at the next arming.
Note: on some vehicles the system automatically disables the volumetric protection if any windows is left opened.
6.6 - Emergency panel LED.
The LED main scope is to show the system arming and disarming conditions. When the system is armed the LED gets
ON and remains illuminated until the 25 s arming period has elapsed. After that it starts blinking. It goes OFF as soon as
the system is disarmed.

INSTALLATION MANUAL 4625 - 4627 CAN/PLIP 13
6.7 - Alarms memory.
Ifthe system has gone off (alarm on) during the arming time itwill warn you with 3 flashes of thedirection lights and 3 audible
signals (5 audible signals if the arming/disarming audible signals function has been activated). It also stores in its memory
the reason of the occurred alarm and shows it on the emergency panel LED. Count the number of flashes and check the
corresponding alarm reason on the table. By turning the key ON the memory will be deleted.
LED NUMBER OF
FLASHES ALARM ROOT CAUSE
1 flash Door opening detection.
2 flashes Ultrasonic volumetric detection.
3 flashes Bonnet opening detection.
4 flashes Ignition key ON detection.
5 flashes Boot opening detection.
6 flashes Door opening detection.
7 flashes Additional sensors.
8 flashes Siren cable cutting - Cobra Bus.
9 flashes Not used.
10 flashes Not used.
11 flashes Immobilizer 1 module connected to the Cobra Bus.
12 flashes Immobilizer 2 module connected to the Cobra Bus.
13 flashes Keyboard module connected to the Cobra Bus.
14 flashes Not used.
6.8 - Emergency disarming.
If the vehicle original remote control get lost or if it doesn’t work, open the door with the mechanical key and turn the ignition
key ON. If the system doesn’t disarm automatically follow the emergency procedure described in the user manual.
6.9 - Alarm condition.
When the system goes off (alarm ON) the siren sounds and the direction lights flash for 28 s.
7. - PROGRAMMABLE FUNCTIONS.
(see the “FUNCTIONS PROGRAMMING TABLES” manual).
8 - HOW TO PROGRAM FUNCTIONALITIES, COBRA REMOTE CONTROLS AND DRIVER CARDS
(optional) SELF LEARNING PROCEDURE.
IMPORTANT: (only for PLIP applications and just after the power supply connection or when the battery has been
disconnected and reconnected). Before entering in the functions programming procedure, arm the system, wait
until the emergency panel LED starts flashing, then disarm the system. From now on it will be possible to performe
the programming procedure.
(see ‘PAGE 1’ and ‘PAGE 2’ of the “FUNCTIONS PROGRAMMING TABLES” manual).

INSTALLATION MANUAL 4625 - 4627 CAN/PLIP 14
9. - FUNCTIONAL TEST.
During the first 25 s after the system has been armed all protection functionalities can be tested without triggering an alarm.
Make the following tests during the 28 s inhibition time with the system armed:
open then close one by one all doors and boot - Check if the system is confirming with three audible signal, each door
opening detection.
Check the proper functionality of the volumetric ultrasonic sensor - Make movements from the back seat, their detection
will be confirmed by a LED flashing.
Note:don’tchecktheproper functionality of the volumetricultrasonicsensorwiththewindows opened as many CAN applications
are automatically excluding this protection when the windows are left opened.
Open the bonnet then lock the vehicle with the remote control - While arming the system will indicate the bonnet opening
with3 flashes of the direction lights and correspondinglywithaudible signals.This test is applicable only ifthesignal is detected
from the CAN network or for systems wired siren.
Try to start the engine - If the engine crankingwires have been connected the engine willnot start. Warning:on somevehicle
by turning the ignition key ON the system will disarm (TRANSPONDER detection).
Check if the PIN emergency Code works properly - By correctly entering the PIN code the system disarms.
10. - CAN / PLIP INDEX MANUAL SELECTION.
The technical support could ask you to manually select a different CAN / PLIP index of the brand which has been loaded in
the main unit. To select a different CAN / PLIP application (CAN INDEX) proceed as follows:
as soon as the system is powered - in the disarming state - the emergency panel LED flashes quickly for 5 s, during this time
framekeep pressed the emergency panelpushbutton until it will gooffthenrelease it.TheLED starts flashing slowly anumber
of time corresponding to the already set index (example 3 flashes for index 3).
WhiletheLEDisflashingslowly,pressbrieflythebuttonof the emergency panel to switch to the next index; each time you press
the button the index increases and so on. By pressing again when the last index has been selected the system will switch back
to the first one of the list. Select the correct CAN / PLIP index, then wait for the LED off to confirm the current index selection.
Note1: the same CAN index can be used for many vehicle models, check the CAN INDEX table available on the web.
Note2: there are four PLIP index available, check the vehicle specific PLIP installation sheet or the PLIP application manual
available on the web in the “Application Manuals” section.
11. - SELF LEARNING PROCEDURE REQUIRED TO REPLACE THE MAIN UNIT OR THE WIRELESS
SIREN REPLACEMENT.
The siren supplied in the kit is delivered already programmed to the main unit. Should you have the need to replace the siren
or the main unit it is required to perform the self learning procedure as follows:
IMPORTANT:don’tperformtheprocedure on two differentvehiclesparkedclosedeachother.Their sirens could be memorized
in one main unit only.
A. Power the main unit by connecting the 24 ways connector.
B. Connect the main unit blue wire to GND (only when a wireless siren is fitted).
C. Open the bonnet.
D. Connect the siren blue wire to GND (if not already grounded through the additional bonnet pushbutton).
E. Disconnect the siren 6 ways connector, then plug it again.
F. Within 60 s turn the ignition key ON, an audible signal confirms that the siren has been stored in the system.
G. Turn the ignition key OFF and disconnect the BLU wires of the main unit and of the siren from GND (if grounded through
the additional pushbutton simply open the bonnet).
Check the system functionality arming the system and triggering the alarm to check the proper sounding of the siren.

INSTALLATION MANUAL 4625 - 4627 CAN/PLIP 15
12. - DOCUMENTS HANDOVER.
Be sure the user user ‘quick reference’ and the PIN code card is placed in the glove compartment and carry out a full
functionality demonstration to the customer.
13. - SYSTEM TECHNICAL SPECIFICATIONS.
The manufacturer shall not be liable for any faults or malfunctions in the anti-theft device and/or in the electrical system of
the vehicle due to incorrect installation and/or to failure to comply with the indicated technical specifications. The system
must only be considered as a deterrent agaist theft attempts.
TECHNICAL SPECIFICATIONS 4625 - 4627
Rated supply voltage +12 V DC
Operating voltage +8 V ÷ +16 V DC
Current consumption (central unit, LED and siren) disarmed 8 mA
Current consumption (central unit, LED and siren) armed 12 mA
Central unit operating temperature - 40 °C + 85 °C
Siren operating temperature - 40 °C + 85 °C
Self power supply Lithium Battery 6 V 1300 mAh
Loudspeaker sound pressure level >115 dB @ 1m
Siren sound pressure level >114 dB @ 1m
- Central dimensions 91x69x35 mm
- Siren dimensions 113x79x45 mm
Trasmitter battery / Cobra Driver Card Lithium Battery 3 V CR2032
14. - FOR
UK
MARKET ONLY
Category 1,2 or 2-1 systems permanently installed as aftermarket equipment by import or distribution centres, vehicle
dealers, or by Independent Installers, shall be installed by companies and technicians who are trained, qualified, industry
recognised professional installers.
Thatchamrecommendstoitsinsurermembersthattheinstallationsofcertifiedproductswithintheaftermarketareregistered
with an independent installation registration system which can be accessed by insurance companies. Thatcham administer
the Thatcham Recognised Installer scheme, on behalf of the British motor insurance industry, providing independent
registration of installations to vehicle owners. Details of the Thatcham Recognised Installer scheme can be found at www.
thatcham.org/tri/home. To ensure consumers insurance cover is not adversely effected it is highly recommended that all
installations are carried out by Thatcham recognised installers and that all installs are registered providing the vehicle
owner with a Thatcham recognition of installation for presentation to insurers.

Cobra Automotive Technologies
via Astico 41 - 21100 VARESE - ITA Y
www.cobra-at.com
06DE3630B - 11/12