CODELOCKS 0460 User manual

INSTALLATION INSTRUCTIONS
Codelocks
0460/0465
0470/0475

A1 x code front plate complete with threaded
cylinder (or europrofile cylinder)
B1 x code front plate lever handle or knob
C2 keys
D1 x back plate
E1 x back plate lever handle or knob
F2 x neoprene seals
G1 x cam plug for use with threaded
lockcase or europrofile lockcase
H1 x gear ring for left hand hung doors
I5 x fixing bolts (1 x spare)
J1 x spindle set
K1 x allen key
L1 x tweezers
M2 x spare tumblers (one red, one blue)
1 x code card
1 x template
1 x installation & operating instructions
1 x code change instructions
BOX CONTENTS
A D
B E
C
F
G
H
IJ
K
L
M
0460/0465 0470/0475
O460 – Narrow stile lock case complete with
threaded cylinder and cams.
0465 – Narrow stile lock case complete with
passage function, threaded cylinder and cams.
O470 – Narrow stile lock case complete with
euro profile cylinder and cams.
0475 – Narrow stile lock case complete with
passage function, euro profile cylinder and cams.
Note: Model number with a ‘K’ suffix indicates knob
handle. Model number with an ‘L’ suffix indicates lever
handle model.
Before installing please check
box contents.
B E

Before fitting the lock to the door please
ensure the lock is handed to suit the door.
IMPORTANT FITTING NOTES:
i) All locks are supplied handed for right hand
hung doors. See step 1 to change the lock
for a left hand door.
ii) Do not turn the key in the cylinder before the
lock is installed as this may put the gear train out
of alignment.
step 1
Changing the hand of the lock for a left
hand hung door.
The locks are supplied with the gear train on
the reverse of the code plate set up to work
with right hand hung doors.
To fit the lock to a left hand hung door make
the following change:
Remove the 6 retaining screws that secure
the plate covering the gear train (fig. 1)
Remove the large outer gear ring which is
marked with a blue line and the letter R.
Replace it with the large outer gear ring marked
with a red line and the letter L (see below).
Flip over the spindle hub so that it shows a red
line and the letter L. Ensure that the red lines are
aligned and vertical.
Replace the plate with the six screws.
step 2
Fit cam plugs to either side of the mortice lock.
Right hand cam to the code side for a right hand
door and left hand cam to the code side for a
left hand door.
If using existing cam plugs remove the projecting
locating pins using pliers.
step 3
Using the template provided accurately mark
and drill the 4 fixing holes using a 6mm drill bit
ensuring that the template is square to the edge
of the door.
step 4
Fit the blue or red tipped spindle into the cam
on the code side according to the hand of your
door (see below).
Fit the butterfly spindle into the cam on the
Non-code side (see below).
step 5
Fit lever handles according to hand of door.
INSTALLATION INSTRUCTIONS
Door hung on RIGHT
viewed from the code side
Door hung on LEFT
viewed from the code side

step 6
Apply the front and back plates with the neoprene
seals in position against the door, over the protruding
ends of the spindles.
IMPORTANT NOTE: To ensure correct functioning
of the lock it is essential that the gear train on
the code plate is aligned correctly before fitting
over the spindles (fig. 1).
If the inner red or blue spindle hub alignment lines
cannot be seen place a screw driver approximately
5mm deep into the spindle hub and turn fully until
it comes to a stop and both the inner and outer
coloured lines can be seen vertically and aligned
(fig. 1).
To align the blue lines for right hand doors turn
the spindle hub fully to the right.
To align the red lines for left hand doors turn
the spindle hub fully to the left.
step 7
Fix the two plates together using the Philips head
bolts, starting with one top fixing and one bottom
fixing. Ensure that the two plates are truly vertical,
tighten fully and fit remaining two bolts.
step 8
Before closing the door, carry out the
following checks:
Enter the code and ensure that the latch retracts
when the lever handle is depressed. Now check
the operation of the inside lever handle. If there is
any binding of the handles loosen the bolts slightly
and reposition the plates slightly until the correct
position is found and then re-tighten the bolts.
To retract the latch with the key
Turn clockwise for a right hand hung door and
anticlockwise for a left hand hung door until the
latch is fully retracted.
To lock out code users by key
For right hand hung doors turn the key 360
degrees anticlockwise from the rest position and
remove the key. For left hand hung doors turn
the key 360 degrees clockwise from the rest
position and remove the key.
step 9
Passage set/Code free operation:
(types 0465/0475 only)
Note that on these locks the ‘Y’ button has a
black dot. To engage code free operation enter
the correct code followed by the ‘Y’ button. The
lever will now retract the latch without having to
enter the code.
To reset to code entry mode press the ‘Y’ button
followed by the ‘C’ button.
N.B. If the ‘C’ button is not pressed the lock
will revert to code free operation after the
next coded entry.
figure 1
spindle hub

CODELOCKS LTD
NEWBURY UK
Tel: [phone]
Fax: [phone]
[email protected]
www.codelocks.co.uk
Helpline, service & spares
FREEPHONE 0800 393405
CODELOCKS LLC
CALIFORNIA USA
Tel: [phone]
Fax: [phone]
[email protected]
www.codelocks.us
CODELOCKS CHINA LTD
Tel: [phone]
Fax: [phone]
[email protected]
www.codelocks.com
II – 0460 – VO1