Comeup Seal Gen2 12.5rs User manual

Self-Recovery Winch
Model: Seal Gen2 12.5rs
PN: 295780 12V 295770 12V
295782 12V
Introduction
Feature
Line pull: 5,670 kg / 12,500 lb synthetic rope first layer
Synthetic rope: 11 mm × 25 m (7/16"×82′) synthetic rope
Brake: Patented cone brake holds full load
Clutch: Turn the T-handle for rapid rope payout
Control: Handheld pendant switch powers the winch or
Built-in digital two ways wireless remote control
Unpacking
．Winch assembly……………………………………………………....... 1 pc
．Control box……………………..................……………....………....... 1 pc
．Remote control………………………………………………………….. 1 pc
．Synthetic rope with sling hook……………………………………….. 1 pc
．Hawse fairlead………………………..………………………………… 1 pc
．1.8 m (6′) 2 gauge battery lead……………………….………………. 1 pc
．Wireless Transmitter……………………………………………………. 1 pc
Read this manual carefully
You should carefully read and understand this manual before operating it.
Careless winch operation may result in personal injury hazards or property
damage.
Installation
Before using the winch, make sure all electrical components have no
corrosion or damaged; the environment should be clear and dry.
Winch and hawse fairlead mountings
•It is very important that the winch will be
mounted on a flat and hard surface of
mounting channel in order to make sure the
motor, drum and gearbox housing are
aligned correctly.
•Hawse fairlead does not mount to the winch directly.
•The synthetic rope shall be wound in an under-wound orientation only.
•Four (4) M10 x 1.50 pitch 10.9 grade with 63.8 N-m torque settings
(maximum) high tensile steel bolts must be used in order to sustain the
loads imposed on the winch mounting.
•Two (2) M10 x 1.50 pitch stainless steel bolts must be used for fastening the
hawse fairlead into the mounting channel.
•Foot forward mounting only.
Wiring Diagram
Attach the black lead firmly to the negative (–) battery terminal and red lead
to the positive (+) battery terminal. The voltage drop for the winch motor
must not exceed 10% of the nominal voltage of 12V DC.
Nut fastening for motor & contactor
1.Holding the lower nut on the stub and fastening the upper nut clockwise.
2.The torque setting for nut is 14 N-m/124 lb-in.

Warning
•The winch is not intended to be used in any manner for the movement or lifting
of personnel.
•The rated line pull shown is based on the first layer of rope on the drum.
•The rope winding on the drum shall remain 10 wraps from the drum to support
the rated load.
•Manufacturer is not responsible for the results of misuse, misapplication, faulty
installation or abuse of synthetic rope in any way.
Parts List
Item No. Description Part No. Qty
1 Waterproof motor w/housing 12V 883544 1
2 Forward Tie bar kit 882521 1
3 Reverse Tie bar kit 882522 1
4 Motor coupling 880005 1
5 Drum bushing 880006 2
6 Drum kit 881521 1
7 Gearbox support rack 882523 1
8 Grounding lead 880009 1
9 Synthetic rope 883285 1
10 1s
t
shaft 881523 1
11 3r
d
ring gear kit 882535 1
12 3r
d
stage carrier 881960 1
13 2n
d
stage carrier 881961 1
14 1s
t
stage carrier 881962 1
15 1s
t
& 2n
d
ring gear 881963 1
16 1s
t
pinion 881964 1
17 Clutch kit 881564 1
18 Gear box kit 882536 1
19 Cone brake disc kit 880122 1
20 Brake clutch base 881100 1
21 Brake cover kit 882537 1
22 Hawse fairlead 883410 1
23 Mounting hardware 880024 1
24 Remote control 880126 1
25 Handsaver strap 880026 1
26 Control box 12V 882780 1
26-1 Remote socket kit 12V 881491 1
26-2 Control pack 12V 882846 1
26-2-1 Wireless receiver 882800 1
26-3 Wireless transmitter 883822 1
27 Sling hook 882477 1
Winch Assembly
2021/09/13 Ver:11