Costway SuperFit SP37619CA User manual

Please give us a chance to make it right and do better !
Contact our friendly customer service department for help first.
Replacements for missing or damaged parts will be shipped ASAP !
Contact Us !
Do NOT return this item.
Treadmill
SP37619CA
USER’S MANUAL
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
EN FR
US:[e-mail]
UK:[e-mail]
AU:[email protected]
US office: Fontana UK office: Ipswich AU office: Truganina
DE office: Hamburg
FR office: Saint Vigor d'Ymonville PL office: Gdańsk

1.Safety Precautions & Warning Instructions
NOTE: Please read the instruction carefully before using and pay
attention to the following safety precautions.
★The treadmill is suitable to be placed indoors to avoid moisture,
splash water and any foreign matter on the treadmill.
★Please wear appropriate sportswear and sports shoes before
exercise. Don't run barefoot on the treadmill and keep your body
stretched.
★ The power plug must be connected reliably grounded, and the
socket must have a dedicated circuit to avoid sharing with other
electrical equipment.
★Children should keep away from the machine to avoid accidents.
★It is necessary to avoid overload operation for a long time.
Otherwise the motor and controller will be damaged. The bearing,
running belt and running plate will be worn and aged. Please keep
regular maintenance.
★Reduce indoor dust. Maintain a certain indoor humidity, avoid
strong static electricity. Otherwise it may interfere with the electronic
meter. Keep controller normally working.
★Please turn off the treadmill power after exercise.
★Keep the clean and fresh air in the room when you use the
treadmill.
★Please fasten the safety lock cable clip on the clothes when
exercising in case of emergency.
★Please stop exercising and consult your doctor if you feel
uncomfortable or abnormal during using.
★Please put silicone oil in a place out of the reach of children to
avoid serious consequences caused by accidental ingestion after use.
Warning: Please observe the following regulations in order
to reduce accidents or injuries to others.
Before You Start
Please read all instructions carefully.
Retain instructions for future reference.
Separate and count all parts and hardware.
Read through each step carefully and follow the proper order.
We recommend that, where possible, all items are assembled
near to the area in which they will be placed in use, to avoid
moving the product unnecessarily once assembled.
Always place the product on a flat, steady and stable surface.
Keep all small parts and packaging materials for this product
away from babies and children as they potentially pose a serious
choking hazard.
02 03

Warning! Enforcement!
Prohibition
★Please check your clothing or zipper before using the treadmill.
★Don't wear clothes that may get caught on the treadmill.
★Do not place the power cord near a hot object.
★Keep children away from the treadmill.
★Don't use the treadmill out of the door.
★The power must be cut off before moving treadmill.
★Non-professional person shall not open the upper guard cover and
the left and right rear housing without authorization.
★This treadmill can only be used in circuit of 15A.
★Only one person can exercise on the treadmill when the machine
starts.
★Please stop exercising immediately and consult a fitness instructor
when you feel dizziness, chest pain, nausea or shortness of breath
during exercise.
(8)Having thrombosis or serious dynamic environment tumor, acute
environment tumor and other blood circulation disorders or a
variety of skin infections and other symptoms.
(9)Having perceptual disabilities caused by diabetes and high
peripheral circulation disorders.
(10)Having skin injuries.
(11)Having a high fever (100℉/38℃or above) due to illness and
so on.
(12)Having abnormal dorsal bones or crooked dorsal bones.
(13)Having pregnancy or possible pregnancy or menstruation.
(14)Feeling abnormal and have to rest
(15)Poor physical condition obviously
(16)Users for rehabilitation purposes.
(17)Feeling uncomfortable in a certain region of the body except
the above circumstances.
——It's likely to cause accident or poor health.
◆Please stop using immediately and consult your doctor when you
feel pain in your back, numbness in your legs, dizziness, abnormal
heartbeats and other body aches that are different from normal or
poor coordination or other abnormal feelings during exercise.
◆Do not allow children to use or play around the product.
——If not followed, there may be a risk of injury.
◆Do not allow children to play with this product for child
protectors.
——If not followed, there may be a risk of injury.
◆Please make sure if there is person or pet around (rear, lower
front) during using or taking out product.
◆Do not use in the state of shell cracked , detached ( internal
structure exposed) or weld detached.
——Otherwise, it's easy to cause accident or injuries.
◆Do not jump up or down during exercise.
——It's likely to fall or cause injury.
Please be sure to discuss with a professional doctor before using if
you are receiving medical treatment from a doctor or the following
patient.
(1)Having back pain now or injury for leg, waist and neck in the past
and the people who have problem with leg (those with chronic
diseases such as disc herniation, spondylolisthesis, cervical
herniation).
(2)Having deformed sex arthritis, rheumatism, gout.
(3)Abnormal people with osteoporosis.
(4)Having circulatory system obstacle (disease of heart,
blood-vessel, hypertension).
(5)Having difficulty in breathing.
(6)Using artificial pacemakers or implantable medical electronic
devices.
(7)Having malignant tumors.
04 05

Do not dissemble the treadmill!
Avoid touching with water!
Prohibition!
Never use it with wet hands!
Pull out the power plug!
◆Do not use or keep in damp places such as outdoors or near the
bathroom, or in places where water drops are caught.
◆Do not use or keep in places with direct sunlight such as
high-temperature places around the stove and heating appliances of
electric heating carpets.
——Otherwise, it's easy to cause electricity leakage or fire.
◆Do not use when the power cord or plug is damaged or the socket
is loose.
——Otherwise ,it's easy to cause electric shock, short circuit and fire.
◆Do not damage or forcibly bend or twist the power cord. At the
same time, do not place heavy objects on it. Or not let the line be
clamped.
——Otherwise, it's easy to cause fire or electric shock.
◆Do not use it with two or more people at the same time. Do no let
the people around get close when using.
——Otherwise, it's easy to cause accident and injuries from falls.
◆Do not use it if you can't express consciousness by yourself or
operation.
——It's likely to occur accident or injury.
◆Disassembly, repair or re-election are strictly prohibited.
——There is a risk of injury due to mechanical failure.
◆Do not pull out or insert the power plug with wet hands.
——It’s likely to cause electric shock or injury.
◆Please pull out the power plug from socket when you don't use it.
——Dust and moisture will reduce the insulation performance and
cause leakage and fire.
◆Do not spray water or other conductive liquid on main body or
operation part.
——It may cause electric shock and fire.
◆People who don't usually exercise shouldn't suddenly do
strenuous exercise.
◆Do not use after eating or when you are tired. Especially after
exercising or when you are in an abnormal physical state.
——It may cause damage to health.
◆This product is suitable for the home use, do not use in the
school, the gymnasium and so on or for non-specific users.
——There would be injury risk.
◆Do not use when eating, drinking or other activities.
◆Do not use it after drinking until you feel sluggish.
——it's easy to cause accident or injury.
◆Do not use it with something hard in your pants pocket.
——it's easy to cause accident or injury.
◆Do not use the power plug with needles, garbage or water.
——It may cause electric shock,short circuit and fire.
◆Do not pull out the power plug or switch the power switch to
"off" during use.
—It may cause injury.
06 07

Grounding instructions!
Danger!
2. Exploded-Views
◆The product must be grounded. Grounding provides the
channel with the least resistance to current to minimize the risk of
electric shock if the function of this machine does not work
normally.
◆This product is equipped with a grounded conductor and a plug
for the device. The plug must be properly installed, grounded and
plugged into an appropriate electrical outlet in accordance with
local codes or regulations.
◆There is a risk of electric shock if the device is not properly
grounded. Please contact an electrician to check if the grounding
of the product is correct, if the plug does not fit into the socket it
can not be changed. Please inform a qualified electrician with the
installation of a suitable socket.
◆This product has a grounding plug. Make sure that the product
is connected to an outlet of the same shape, this product can not
be used with an adapter socket.
◆Please be sure to pull the power plug from the socket during
maintenance.
——Failure to comply may result in electric shock or injury.
◆Please stop using it if the device does not start or runs abnormally.
Immediately pull out the power plug and entrust inspection and
repair.
Failure to comply may result in electric shock or injury.
◆Pull out the power plug immediately in case of power failure.
——Otherwise, an accident or injury may occur after the power is
restored.
◆Do not hold the cable tight. Hold the power plug to pull out the
plug.
——Otherwise, it may cause short circuit electric shock and fire.
Packing list ：
Main machine
1
Riser down cover
Spare parts package See spare parts list table
No. Item name Qty. Notes
2
3
1
2
1
Computer Display
Digital Meter
Handle Pulse
Handle Pulse Right Handlebar
Cover
Right Handlebar
Inner Cover
Right Riser
Safety
Key
Riser Down Cover
Riser Down Cover
Left Riser
Left Handlebar Cover
Running Belt
Right Rear
Tailstock
Adjustable Foot Pad
Left Rear Tailstock
Motor Bottom Cover
Side Edging
Side Edging
Motor Cover
08 09

Technical Parameters
Working voltage
Maximum load
Dimensions
Running area
Motor peak power
Speed
Φ8 gasket
5mm Allen key
6mm Allen key
Safety Key
Silicone oil
1
2
3
4
5
6
7
8
2
2
1
1
1
2
Each
*1
4
Manual Certificate of
Conformity
M8*16 hexagon socket
pan head screw Fix the computer display
and the riser
Fix the computer display
and the riser
Assembling machine
Item name NotesQty.NO.
Lock the main frame and
the riser, adjust the
running belt
Foot Pad
AC-110V 60Hz
220lbs
51"L*26.3"W*41.8"H
43.3"*16.5"
2.25HP
0.6-7.5mph
Schedule (list of accessories) :
Exploded-Views
1
2
3
4
29
5
6
7
33
34 19
10 11
12
13
23
32
42
25
27
64
36
21
31
28
65
62
57
56
37
38
41
49
55
43
27
47
46
48
50
51
63
60 58 62
53
54
11
32
42
25
30
27
27
35
43
47
40
46
48
50
51
44
52
52
23
63
60
60
60
52
54
53
26
8
914
15
16
17
22
24
30
30
30
39
39
44
45
52
52
54
18
59
61
20
60
60
20
10 11

Details of Exploded-Views
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
2
1
4
1
1
1
1
6
1
2
1
1
1
1
1
1
2
1
1
2
3
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
Main frame
Left riser
Right riser
Computer frame
Front roller
Rear roller
Running deck
Motor
Upper guard
Lower guard
Side edging
Decorative cover for left rear tailstock
Decorative cover for right rear tailstock
Left handle outer cover
Left hand handle inner cover
Right handle outer cover
Right handle inner cover
Main frame middle horizontal tube
Display fixing frame (choose one of two)
Computer bottom case
Computer display sticker
Upper shield sticker
Item nameNo. Qty 23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Riser lower cover
Controller
Foot pad
Speaker
Running board rubber pad
Computer PCB board
Safety key iron plate
Side edging block
Safety key sets
Moving flywheel
Running belt
V-belt
Wire clamp
Power cord clip
Rocker switch
Power cord
Spring
Safety lock sensor
Buttons key board
Square pipe plug
Hexagon socket head screw M8x55
Hexagon socket head half-thread screw M8x40
Item nameNo. Qty
12 13

3. Installation Steps
1. Take the main machine out of the carton box and lay it flat on the
carpet or soft cushion. Step①: put the main machine on its side,
screw the four foot pads clockwise into the screw holes on the back
sides, and then lay it flat. Step②⑤: lift the riser up, and turn the
computer display to the position shown in the figure (don't press the
communication line when the computer display component is put
down, to prevent damage to the lines when installing screws). Step
③④: use the "6MM Allen key" to lock the left and right risers to the
frame. Step⑥: use "M8*16 hexagon socket pan head screws" and
M8 washers to lock the computer display on the left and right risers.
Step⑦: after confirming that the riser is locked, fasten the lower
cover of the riser on the left and right risers respectively.
45
46
47
48
49
50
51
52
53
54
55
56
57
58
2
2
2
2
1
2
6
21
2
6
2
1
1
16
14
Hexagon socket head screw M8x12
Hexagon socket pan head half-thread screw M8x30
Hexagon socket pan head screw M8x35
Hexagon socket pan head screw M8x16
USB
Hexagon socket countersunk head screw M8x35
Hexagon socket countersunk head screw M8x20
Cross recessed pan head tapping screw 4.2x16
Hexagon lock nut M8
M8 gasket
Communication line
Upper section of communication line
Lower section of communication line
Cross recessed pan head tapping screw 2.9x6.5
Cross recessed countersunk head tapping
screw 4.2x30
Cross recessed pan head tapping and self-drilling
screws 4.2x16
Cross recessed countersunk head tapping and
self-drilling screws
Cross recessed pan head tapping screw 4.2x22
Cross recessed flange head tapping screw 2.6x9
EVA adhesive tape
Button sticker
Item nameNo.
59
60
61
62
63
64
65
21
2
10
6
1
1
Qty
14 15

Frequency
The exercise of the same muscle should keep 48 hours of rest.
That is, only train the same area every 2 days.
Load
Relax
Diet
Stretching exercise
Determine the amount of training according to the individual physical
condition, and then practice according to asymptotic load. It is
normal phenomenon for muscle soreness at the beginning of training.
As long as continue to practice, the soreness can be eliminated.
The reductive action should be done for 5mins after practicing every
time. Especially extend flabby for ministry muscle. Avoid long-term
coagulation of muscles and maintain muscle flexibility.
Do not eat at least 1 hour before training and half an hour after
training to protect your digest system. Do not drink plenty of water
to avoid increasing the burden on the heart and kidneys.
It is important to stretch before training, no matter how intense the
training will be. It is easier to stretch the muscles when they are
warm, warm up by running for 5 to 10 minutes and then stop and
stretch as follows 5 times for 10 seconds or more on each leg.
Continue to stretch even after training. Do it again after exercise.
12
34
5
2. Step⑧: when the "safety key" is drawn into the yellow position of
the computer display, and the installation is complete. Turn on the
power switch under the front of the machine, and enter the standby
state.
Note: After the machine is assembled,
please check again whether all bolts
are locked.
Warm-up exercise
warm up for 5-10mins before each operation
Breathe
4. Sports advice and guidelines
Do not hold your breath during operation. Normally prepare to
release action and inhale through the nose, exhale through the
mouth. The breathing should be coordinated with movement. If
the breathing is too rapid, the movement should be stopped
immediately.
16 17

1. Stretch down
Bent your knees slightly, then slowly bend your body to relax your
back and shoulders. And try to touch your toes with your hands.
Hold for 10-15 seconds, then relax. Repeat three times (see figure 1)
2. Hamstring stretch
Sit on a clean seat cushion and straighten one leg. Bring the other
leg in close to the inside of the leg. Try to touch your toes with your
hands. Hold for 10-15 seconds, then relax. Repeat 3 times for each
leg (see figure 2)
3. Stretch the calf and hamstring
Stand with two hands on a wall or tree. One foot is behind. Keep
your hind legs straight and on your heels, leaning against a wall or
tree. Hold for 10-15 seconds. And then relax. Repeat 3 times for
each leg (see figure 3)
4. Quadriceps stretch
Keep balance with left hand to hold the wall or table. Then extend
your right hand backward. Hold your right ankle and slowly pulling
toward your hips until you feel tension in front of your thighs
muscles. Hold for 10-15 seconds, then relax. Repeat 3 times with
each leg (see figure4)
5. Sartorius muscle (muscle of the inner thigh) stretch
Sit with your feet facing each other and knees facing out. Grab both
feet with both hands and put toward the groin. Hold for 10-15
seconds. Then relax, repeat 3 times (see figure 5)
5.Operating Instructions
How to use the treadmill
1. Turn on the power and check if the machine is normal.
2.Set the running speed of the running belt to 0.6-7.5 mph.
3.Clip the safety lock on the placket on the chest of the athlete.
4.Before exercise, check the stability and function of the treadmill.
It is strictly forbidden to stand on the running belt to start the
treadmill. Before running, stand on the left and right bars, hold the
handrail, and then step into the running area after starting
normally. Take the belt for exercise. When starting up, grab the
handrail with one hand and press the "START" button on the
electronic watch with the other hand. The treadmill will start at 3
seconds and run at 0.6 mph. Press "+", the motor speed rises to
reach the speed of 1.5-2.1mph (this is the most comfortable speed
to learn running), both hands grab the armrests at the same time,
both feet step on the running belt, and will soon be able to run
With the same speed.
5.After a few minutes, you can increase the running speed, press
the "+" button on the digital meter to increase the speed slowly; or
press the "-" button to decrease the speed.
6.You can stop the motor at any time by pressing the "STOP"
button on the digital meter during the movement.
7.After starting the machine, press the "3 mph" speed direct
selection button directly at any speed, then the running speed of
the running belt is 3mph.
Note: When the safety key is pulled off during the movement, the
treadmill will immediately stop during exercise. The display will
stop all functions and shows "E07".
18 19

Display window and button description
1. LED window shows the following functions:
Time / speed / distance / calorie /pulse window: 5 seconds to
switch display time, speed, heart rate distance and calorie data.
Time display range: 0:00-99:59
Speed display range: 0.6-7.5 mph
Distance display range: 0.00-99.99
Calorie display range: 0.00-999.9
Heart Rate display range: 50-200
2.Electronic watch function button: 3 mph, speed +, speed -,
stop, start, program, mode.
A. 3 mph: After starting up, press this speed direct selection
button directly at any speed, then the running speed of the
running belt is adjusted to 3mph.
B. SPEED+: During the exercise, the button will increase the
speed.
C. SPEED-: During the exercise, the button will slow down the
speed.
D. Stop: press this button in the running state, the treadmill
decelerates to stop.
E. Start: Press this button in the stop state, it will start the
running belt.
F. Program key: In the stop state, press the program key to cycle
through the program:
manual mode->P01->P02->P03->P04->P05->P06->...P11->P12.
G. Mode key: When manual mode is selected, the initial value
displayed in the speed window is 0.0, and the mode key can be
cycled to select the countdown mode: Window displays
30:00->Countdown distance mode: window displays
1.0->Countdown Calorie mode: window shows 50->Normal mode.
Startup instructions
1. Place the security lock on the panel, turn on the power switch,
and the buzzer will sound. Then enter the manual normal mode.
2. Press the start button, the time window displays 3 seconds
countdown, and each time the buzzer is sounded, the motor is
started.
3. The starting speed is: 0.6 mph. At this time, you can press the
speed +, - keys to adjust the speed and the 3 mph speed direct
selection button.
4. Run in normal mode, time is running at regular timing, speed is
fixed, can be adjusted manually.
5. Heart rate test, hold the light hand grip with both hands, and
have a heart rate displayed in heart rate window after a few
seconds. (Heart rate data is for reference only and cannot be used
for any medical-related purposes)
Safety lock function
Power saving mode
In any state, the safety lock is pulled off, the window displays "E07",
and the buzzer BI-BI-BI rings three times. If the motor is running,
the motor is stopped urgently. When the safety lock is off, it cannot
be started.
The system has a power-saving function. If there is no key
command input within 10 minutes in the standby state, the system
enters the power-saving mode, automatically turns off the display,
and presses any key to wake up the system again.
20 21

6. Common failures and processing method
please contact our after-sales service if you have any other questions
Error messages on electronic meter and elimination methods
Questions Questions
E01
E02
E03
E04
E05
E06
E07
poor communication
power assault
Non-sensing signal
overload protect
Possible Cause Maintenance Methods
safety lock drop
external disturbance
system self-check
failed
The signal line is not plugged.
Plug it again
power tube breakdown,
replacement of electronic
control
sensing wire is not plugged in
properly. Plug it again correctly
overload, replace controller
or motor
overload,replace contoller
system failure, replace
controller
put the safety lock in
correct position
turn off power switch, turn it
on after one minute
abnormal
display
controller or motor
abnormal
treadmill
don't work
the running
belt doesn't
run smoothly
running belt
slipped
Possible Causes
Put the power switch
in“ON" position
put the safety lock in
correct position
check the controller input
terminal and signal circuit
replace fuse
put plug to insert socket
not connected
power is not turned on
the fuse blew out
insufficient lubrication
running belt is too tight
running belt too loose
running belt is too tight
add silicone oil lubricant
adjust running belt tightness
adjust running belt tightness
adjust running belt tightness
circuit signal system
break
safety lock drop
Maintenance Methods
22 23

Please adjust left bolt with
clockwise or right bolt with
counterclockwise if running
belt deviates to the left.
Please adjust right bolt with
clockwise or left bolt with
counterclockwise if running
belt deviates to the right.
3. Adjust tightness of running belt
All treadmills shall be adjusted for tightness before delivery and
after installation. However, the running belt may be loosened after a
period of use. For example,the treadmill has problems with stopping
and slipping during exercise. Adjust bolts of running belt with the
left and right synchronous as per clockwise direction to half a circle
as the unit when this phenomenon occurs. The feet will slip if the
running belt is too loose. But it is not good to be too tight. It is easy
to increase the load of the motor and damage the motor, running
belt and roller etc.
4. Running belt deviation adjustment
All treadmills need to adjust the running belt before delivery and
after installation. But the running belt may be deviated after a
period of use which may be caused by the following reasons:
① The main body is not placed smoothly.
② The feet of users are not in the center of the running belt.
③ Uneven force on the user's feet.
It will be returned to normal after a few minutes of no-load
rotation if deviation is caused by man-made. It should be
adjusted with 6mm wrench at a half circle as the unit for
deviation of non-recover automatically.
The running belt deviation is mainly maintained by the user according
to the manual. Running belt deviation will seriously damage the
running belt.This point must be found in time and corrected at once.
Advice:
★1 hour or less per week
★Less than 3 hours per week
★3-6 hours per week
lubricate once every 6 months
lubricate once every 3 months
lubricate once every 2 months
7. Product maintenance
1. Lubrication
When the running machine is used for a period of time, it must be
lubricated with special methyl silicone oil.
2. As for the way to check if you need to add lubricant.
Just grab the running belt and touch the middle of the
running belt back with your hands as much as possible.You
don't need to add lubricant if you have silicone on your hand
(a little damp). You have to add lubricant if the pad is dry
and there is no silicone on your hand.
More than 6 hours per week lubricate once a month. Do not
lubricate too much. It is not the more lubricants the better.
Remember: Proper lubrication is an important factor in improving
the life of the treadmill.
★Steps to add lubricant to the running plate (as shown in the right
picture)
★Stop running and fold the machine.
★Lift the running belt of the underside of the main body. Put the
oil pot as far as possible into the middle of the running belt. And
spray methyl silicone oil inside of the running belt and both sides.
★You can make use of the treadmill speed of 1km/h to evenly
lubricate and step on the running belt from left to right. After a few
minutes, the methyl silicone oil can be completely absorbed by the
running belt.
24 25

Gymax App iOS/Android with Gymax platform provides users the
control of sports intelligent device, sports data recording, sports
mall, dynamic sharing in community, system settings and other
functions.
Retrieve Password
If E-mail users forget Passwords, users can click "Forget Password"
on the mailbox login interface to jump to the Password retrieval
interface, and then reset Passwords.
Edit Information
In the personal information interface, clicking the avatar, users can
edit the avatar and upload the avatar by choosing album or camera.
This document is applicable to the Android version and iOS version of
the official APP of Gymax.
For the convenience of users, Gymax
provides three login methods: Facebook
and E-mail, and iOS users can also sign
in with Apple. Users can quickly sign in
to the Gymax App and use it.
Sign In
Sports Scenes
Sports Mall
Community Dynamic
Settings
Sign in Process
The Main functions
Functions Overview
Gymax App Instruction Manual
ios: Search Gymax in App Store to download
Android: search and download from Google Play store
26 27

Sports Scenes
Connecting services
On the home page, users can freely choose the device type to
connect. After connecting successfully, then user can select the
device page, such as the "Treadmill" interface.
Starting exercise
Selecting the device page, such as "Start" on the "Treadmill"
interface, users enter the running free, as shown below:
1.Waiting for Gymax to automatically connect to the treadmill.
3. The Gymax App synchronizes exercise data, such as distance,
time, calorie, and speed. As users run on the treadmill, they can
start and stop the treadmill. And they can increase and reduce the
speed. The APP directly shows the user's sports ranking and the
number of online users.
2.When the connection status sign is lit, it means that the APP
has successfully connected to the treadmill. Users click ,then the
treadmill starts running and enters the countdown.3.2.1 GO.
28 29

4. When users finish the exercise, the Gymax App will show users'
total running distance.
Sports Plan
Users can click "Add More Training Plans" to add users' own sports
plans.
Setting Goals
1. Users can set suitable sports goals.
5. Users can share the sports data to the community or save it to
the phone album.
30 31

2. When the goal is reached, the exercise automatically ends.
Training Course
1. Users can select courses in the interface of training course.
2. And then start training with a fitness coach.
Exercise Record
The user can view the exercise data record in the device page.
(me-exercise data)
32 33

Sports Mall
Users can purchase satisfied sports devices.
Community dynamic
1. In sports community, users
can share dynamic
communication with each other.
2. Users can
comment dynamics
in community.
3. Users can post
dynamics.
4. Users can remove
the released dynamics
in Me-My Dynamic.
34 35

Settings
System Settings
Users can click "Me" to enter the set up,
including unit, feedback, terms of agreement,
privacy agreement and clear cache, etc.
Users can clean up the system
cache according to users' needs,
including Gymax App H5 web page
load cache and image load cache.
Users can submit suggestions
and the problem for improving
the product.
Unit settings (metric or
imperial standard)
Feedback
Clear Cache
36 37

EN FR
VEUILLEZ NOUS DONNER L’OCCASION DE L’AMÉLIORER !
Contactez d’abord notre service à la clientèle amical pour l’aide.
Les replacements pour les pièces manquantes ou endommagées seront envoyés
le plus vite possible!
Contactez-nous !
Ne retournez pas cet article. FR:[email protected]
Tapis Roulant
SP37619CA
MANUEL DE L’UTILISATEUR
Contactez notre service à la clientèle pour obtenir de l’aide.
CE MANUEL CONTIENT DES INFORMATIONS IMPORTANTES SUR LA SÉCURITÉ. VEUILLEZ LE LIRE ET LE CONSERVER POUR TOUTE RÉFÉRENCE FUTURE.
US office: Fontana UK office: Ipswich AU office: Truganina
DE office: Hamburg
FR office: Saint Vigor d'Ymonville PL office: Gdańsk