Creda Spa300c User manual

IMPORTANT:
This booklet should be left with the user
after installation and demonstration
CREDA SPA300C
ELECTRIC SHOWER
Installation and User Guide

2
INTRODUCTION
If you experience any difficulty with the installation or operation of your new
shower, thenplease refer to the “What to do if things go wrong” section in this
manual before contacting us.
Section
Introduction . .. . . . .. . . .. . .. .. . .. ..
Important Safety Information .. . . . .. . . .
How to install your SPA300C Shower . .. . .
Cold WaterInlet Pipe Configuration. . . . . . .
Assembly of Accessories . . . . . .. .. . . . ..
How tomaintain your SPA300C Shower. . ..
AdditionalAccessories and Common Parts . .
How to use your SPA300C Shower (Detailed)
Page
2
2
3
5
7
7
7
8
Section
What todoif thingsgowrong (1)
Self Help . .. . . . .. . . . . . .. . .. .. . .. ..
What todoif thingsgowrong (2)
Professional Service . .. . . .. . .. .. . .. ..
How your SPA300C Shower Works . .. .. . .
Creda After Sales Service . . .. .. . . . .. . .
Guarantee and Contact Details . .. .. . .. ..
How touse your SPA300C Shower
(Summary)
Page
9
9
10
11
11
12
Thank you for purchasing a quality Creda SPA300C Shower manufactured in England.
To enjoy your new shower at its best, please take time to read this manual thoroughly to
familiarise yourself with all instructions, BEFORE beginning installation.
Having done so, keep this manual handy for future reference.
Your shower is designed to stabilise temperature changes caused by w
ater pressure fluctuations.
These can result from toilets being flushed or taps being turned on and off.
When this happens your showering temperature will be held within a controlled band, provided that
the minimum pressurerequired by the shower is maintained (see “Effect of Other Water Devices”).
1. Your shower has been designed for convenience, economy and safety of use, provided that it is
installed, used and maintained in good working order and in accordance with our instructions and
recommendations.
2. All wiring and installation must be supervised by a suitably qualified person.
3. THIS APPLIANCE MUST BE EARTHED.
4. The installation must be in accordance with the current edition of BS.7671 (the “IEE Wiring
Regulations”) and “Part P” of the “Building Regulations” in force at the time of installation.
Installations outside of England and Wales must also conform to any local regulations in effect.
This appliance is intended to be permanently connected to the fixed electrical wiring of the mains
supply with its own dedicated supply.
5. This appliance must NOT be fitted where it may be subjected to freezing conditions.
6. DO NOT switch the appliance on if you suspect it of being frozen.
Wait until you are sure it has thawed out.
7. DO NOT fit any sort oftap or control on the appliance outlet. The appliance is designed to have
an open outlet and should only be used with “Creda” recommended fittings.
8. Take care to avoid restricting the outlet of thepressure relief device.If water is discharged from
the pressure relief device, maintenance will be required before the appliance can be safely used.
9. Isolate the mains electrical and water supply before removing the front cover of the appliance.
CONTENTS
IMPORTANT SAFETY INFORMATION

3
WARNING: ALL WIRING AND INSTALLATION MUST BE
SUPERVISED BY A SUITABLY QUALIFIED PERSON.
WARNING: DO NOT INSTALL THIS SHOWER WHERE IT MAY BE
SUBJECTED TO FREEZING CONDITIONS
We recommend that the installation is done inthe following sequence.
a. Fixing the shower to the wall b. Plumbing c. Electricalconnections
a. FIXING THE SHOWER TO THE WALL
1. Position the riser rail at a convenient height for majority of users as
detailed in Diagram 1 and mark its position.
2. Position the heater so that the top of the unit is horizontaland level
with, or a maximum of 0.6 metres (2ft) below the top of the
riser rail. Choose a flat piece of wall to avoid the possibility of
distorting the backplate, as this may make the front cover a poorfit.
3. Adjust the position to get the most convenient arrangement taking
the following into account.
•The heater must not be mounted in the direct spray from the handset.
•The handset must not be able to come into contact with used waterin the cubicle, bath or
basin. If it can, then a vacuum breaker must be fitted (available from us if required).
4. Fix the riser rail with screws provided
.
The fixing holes at the base of the brackets will be disclosed by removing the plastic fronts
.
See Diagram 4 and instructions supplied withaccessories for further details.
5. If you have not yet done so, remove the front cover assembly by undoing the retaining screws at
the top and bottom of the unit and lifting the cover off.
6.
Your shower unit not only accepts services from the top, bottom or rear.
It also accepts services from the left or right hand side of the unit.
Decide the position of
the electrical cable into the unit.
If top entry is chosen, cut away the walls in the backplate as shown in Diagram 2a.
If bottom entry is chosen, cut away
the walls in the detachable bottom
section as shown in Diagram 2b.
The detachable bottomsection is
secured to the backplate by 2 screws.
7. Decide the position of entry of the
cold water pipe into the unit.
If top entry is chosen,
cut away the backplate as shown in
Diagram 2a.
If bottom entry is chosen, cut away the
walls in the detachable bottom section
as shown in Diagram 2b.
If rear, please read the section on plumbing. To aid installation, youmay find it convenientto
move the flexible pressure relief valve outlet assembly by removing the two securing screws.
If you do, please ensure that they are fully tightened on re-assembly (see Diagram 2b).
HOW TO INSTALL YOUR SPA300C SHOWER

4
8.
Your shower is providedwith 3 fixing
positions in the backplate (see Diagram 6).
The top-fixing hole is a “key-
hole” slot,
and should be marked and drilled first.
Tighten top screw with h
ead protruding
about 10mm from the wall and hook the
backpla
te over the screw head.
This allows for correct and accurate
alignment of your shower before marking
and fixing the bottom positions.
You may not wish to tighten up both screws at this
stage as the holes are elongated to allow for adjustment after other connections have taken place.
b. PLUMBING (For your convenience a cold water inlet configuration diagram is shown on page 5)
WARNING: ENSURE THAT THE MAINS WATER SUPPLY MEETS THE REQUIREMENTS BELOW
BEFORE CONTINUING WITH INSTALLATION.
The heater must be connected to the mains cold water supply.
This must have a minimum running pressure of69kPa (0.7 bar, 10 psi)
and a maximum pressure of 690kPa (7.0 bar, 100 psi).
WARNING: BEFORE CONNECTING THE PIPE WORK TO THE SHOWER,
ENSURE THAT THE PIPE WORK IS FULLY FLUSHED OUT.
1. Unscrew the “Red Cap” from the shower outlet pipe and discard it in a suitable manner.
It has been used to seal the shower during transit, and is no longer required.
2. It is recommended that a WRAS (Water Regulations Advisory Scheme) listed isolating valve is fitted
to the incoming mains cold water before the shower unit. This will allow the unit to be serviced or
exchanged without having to turn off the mains water at the water stop valve.
3. The heater can be fed from a header tank provided this has a minimum head of 7 metres (23ft).
4. The cold water inlet connection sup
plied is a plain Ø15mm straight shank/shaft.
This connector will accept either a Ø15mm compression elbow or a Ø15mm “push-on elbow”.
Ø15mm copper, stainless steelor suitableplasticpipeshould beused.
For your convenience,acold water inletconfiguration diagramisshown onpage 5
.
Ifrear entryisrequired,treatastopentrywithanadditional“Yorkshire”elbow(solderedtype)for
fitting intotherear channel.
Toaid installation,youmayfind itconvenienttomovetheflexiblepressurereliefvalveoutlet
assembly by removing thetwosecuring screws (Se
eDiagram2b).
Inmultipleinstallations,correctpipeworksizesshouldbecalculatedtomaintain adequateflowto
each shower.
5. It is permissible to use a WRAS (Water Regulations Advisory Scheme) approved sealant sparingly
whilst avoiding excess finding its way into the shower operating parts.
6. With isolating valve connected, flush the pipework through to remove any particles etc,
before making the final connection to the shower.
Blockage in the water ways (particularly the handset and solenoid valve) will prevent the heater
working properly. Note:You may be charged for a service call if it is due to incorrect installation.
7. The shower is designedto have an open outlet and should only be used with “Creda” recommended
fittings.
Do not connect the handset until after the frontcover and detachable bottom section are fitted.
WARNING: DO NOT FIT A TAP ON THE SHOWER OUTLET.
WARNING: TAKE CARE TO AVOID RESTRICTING THE OUTLETOF THE
PRESSURE RELIEF VALVE.

5
Please note that standard compression fittings are shown.
Push-Fit connections or a combination of the two are also suitable.
To aid installation, youmay find it convenientto move the flexible pressure relief valve outlet
assembly by removing the two securing screws.
If you do, please ensure that they are fully tightened on re-assembly (see Diagram 2b).
COLD WATER INLET PIPE CONFIGURATION

6
c) ELECTRICAL
WARNING: THIS SHOWER MUST BE EARTHED.
The electrical installation must be in accordance with the current BS.7671 (IEE Wiring Regulations)
and “Part P” of the Building Regulations and/or local regulations.
1. The shower unit is designed for a single phase AC electrical supply.
Please check the rating plate on the unit to see what details apply to your shower.
AS A GUIDE ONLY (* Only applies if external earth impedance is less than 0.35 Ohms)
Rating Cable Sizes
Fuse / MCB
Cable Length
6.0mm²
10.0mm² 40A Type B MCB 27m Max.
45m Max.
8.5 / 7.8kW 240 / 230V 6.0mm²
10.0mm² 45A BS.1361 fuse 12m Max.* 21m Max.*
6.0mm²
10.0mm² 40A Type B MCB 27m Max. 45m Max.
9.5 / 8.7kW 240 / 230V 6.0mm²
10.0mm² 45A BS.1361 fuse 12m Max.* 21m Max.*
10.5 / 9.6kW 240 / 230V 10.0mm² 45A BS.1361 fuse 12m Max.*
Remember to upgrade the cable if it runs in thermal insulation in a loft,or for a longer distance.
2. A means for disconnection in all poles must be incorporated in the fixedwiring in accordance with
the wiring rules. We recommend a ceiling switch mounted in a convenient position.
3. If you have decided to connect the cable on the left hand side then please remove and use the
cable clamp that was provided along the right side (see Diagram 3a/b).
WARNING: IF LEFT HAND SIDE CABLE ENTRY IS USED, THE MAINS CABLE OUTER SHEATH
MUST BE STRIPPED BACK TO THE LEVEL MARKED ON THE BACKPLATE, AND ALL
THREE CONDUCTORS MUST BE FULLY SLEEVED WITH THE SLEEVING PROVIDED
BETWEEN THERE AND THE TERMINAL BLOCK (SEE DIAGRAM 3a).
4. Connect cable to terminal block making sure that all the retaining screws are VERY
TIGHT and that no cable insulation is trapped under the screws.
WARNING: FAILURETO COMPLY WITH THESE INSTRUCTIONS COULD
RESULT IN FAILURE OF THE TERMINAL BLOCK.
5. Re-fit the detachable bottom section with the two screws if it was removed.
IMPORTANT: Ensure you connect the flying lead from PCB to the front cover.
6. Re-fit the front cover, and secure by replacing the top and bottom fastening screws.

7
HOW TO MAINTAIN YOUR SPA300C SHOWER
ASSEMBLY OF ACCESSORIES
Diagram 4 (Riser Rail and Soap-Dish Fitting Instructions)
(Refer to the separate fitting instruction sheet packed with the accessories for more details)
1. Establish height of riser rail to suit user requirements. This should be a maximum of 0.6 metres (2ft) above the level
of the heater, see (a) and Diagram 1.
2. Remove covers from the wall brackets (b), and position the lower bracket and mark the wall for the screw fixi
ng (c).
Then drill and plug the walland fix the lower bracket without the rail location notch.
3. Fit the rail into the lower bracket. Place the remaining bracket with the rail location notch on the top of the rail,
making sure that the rail slot is located into the notch.Ensure the hole position is vertically aligned and mark the
wall (d). Remove the rail and bracket, then drill and plug the wall.
4. Assemble the height adjuster (e). Compress the height adjuster and slide onto the rail. Fit the hose retaining ring
and then the soap dish on the bottom of the rail (f). Lock the soap dish into position by tightening the lock nut.
5. Replace the rail assembly into the lower bracket. Refit the top bracket, ensuring the slot in the rail is located into
the bracket notch and fix tothe wall. Slide covers onto both brackets.
NOTE: The adjustable slider grips the conical nut on the shower hose (g)
A more comprehensive list of additional
accessoriesand spare parts canbe supplied
from Creda Sales Hotline [phone]
7. Fit the shower hose, and operate the shower first without the handset to flush out particles,
fit the handset and then operate the shower as on page 8 or 12 and check:
•Water gets to a satisfactory temperature and water flow can be adjusted by control knob “E”.
•Knob “E” has been correctly engaged by ensuring that the knob turns approximately one full turn.
•Power selection operates in all 3 button settings, giving a change in water temperature.
•Check again for leaks and that the holes in the shower handset are notblocked.
8. Demonstrate the showers operation to allusers.
It is recommended that the shower unit and hose etc. be cleaned usinga soft cloth and that the use of
abrasive or solvent based cleaning fluid be avoided, especially on any plated finishes.
We recommend that before any cleaning, the isolating switch be turnedoff, thus avoiding accidentally
switching on the shower.
WARNING: YOU MUST REGULARLY INSPECT THE SHOWER HOSE FOR WEAR
AND DAMAGE. REPLACE IFNECESSARY, OREVERY TWO YEARS,
WITHANAPPROVED PART.
WARNING: INORDERTO MAINTAINTHEPERFORMANCE OF YOUR SHOWER,
YOUMUST REGULARLY CLEAN THE SHOWERHANDSET.
All water contains particles of lime-scale, which build up in the shower handset and
unit reducing the performance.
It is therefore importantto clean the shower handset by simply rubbingthe rubber
nozzles, or soaking in proprietary lime-scale remover and rinsing thoroughly before use.
NOTE: After use it is normal for some water to drip from the shower handset for a
few moments. This inhibits lime-scale build-up over prolongeduse.
Please Note:- The fitting of Spare Parts must be supervised by a suitably qualified person.
WRAS Listed Water Front Coverwithout PCB Cat No. 93550813
Isolating Valve Cat No. 93792452 Front Covercomplete with PCB Cat No. 93550814
Curtain and Rail Pack Cat No. 83792812 Thermal Cut-Out 50/88°C Cat No. 93597871
Solenoid Valve Cat No. 93590355
ADDITIONAL ACCESSORIES COMMON SPARE PARTS

8
IF WATER IS TOO COLD
Turn Knob “E” anti-clockwise “1/8” of a
turn, and continue turning anti-clockwise until
you get the water temperature of your liking.
Wait 20 seconds after each adjustment for
the water temperature to stabilise.
The final adjustment may be in any position.
If after turning fully anti-clockwise water is
still too cold, set shower pattern on shower
handset to outer or inner pattern only.
IF WATER IS TOO HOT
Turn Knob “E” clockwise “1/8” of a turn, and
continue turning clockwise until you get the water
temperature of your liking.
Wait 20 seconds after each adjustment for the
water temperature to stabilise.
The final adjustment may be in any position.
If after turning fully clockwise, water is still toohot,
press Button “B” (II -medium) and re-adjust Knob
“E” to give desired temperature.
Water flow will be reduced on this setting.
1. Ensure the electricity and water are turned on to the unit.
2.
Your shower can be turned on by pressing either
Button “A”, Button “B” or Button “C” (see Diagram 5).
Button “A” (III) - Starts shower on “High” power.
Button “B” (II) - Starts shower on “Medium” power.
Button “C” (I) - Starts shower on “Cold”.
Once pressed, a light will illuminate above the button
confirming that power selection has been made.
Knob “E” controls the temperature of the water, and
For this example turn Knob “E” to “mid-position”.
3. Press Button “A” and the water will flow.
4. Allow about 20 seconds for the temperature ofthe water to stabilise.
It is recommended that you do not wholly enter the water spray
during this period, even if the shower has just been used.
5.
Once a temperature setting to your liking has been achieved, Knob“E”will rarely needadjusting.
You must however take into account required adjustments for variations of incoming mains water
temperature between summer and winter (see “Effect of Seasonal Incoming Water Temperature
Changes” page 10).
6. When you have finished showering, press button “D” ( ) only, the LED light above will flash.
Water will continue to flow for up to 7 seconds before switching off.
Wait for the water to stop, and then switch off the electricity at the ceiling switch or local isolator.
7. Turning the shower onby pressing Button “B” reduces the power used by the shower givinga
cooler shower or the option of reduced water flow.
This option is mainly for summer usage and if this is used then Knob “E” must be re-adjusted.
8. Turning the shower onby pressing Button “C” will supply water without any heating
.
9. Your shower is designed to stabilise temperature
changes causedby water pressure fluctuations
(see “Effect of Other Water Devices on Incoming Water Supply” see page 10).
WARNING: DO NOT SWITCH THE SHOWER ON IF YOU SUSPECT IT OF BEING FROZEN.
WAIT UNTIL YOU ARE SURE IT HAS THAWED OUT.
WARNING: DO NOT OPERATE THE SHOWER IF WATER IS DISCHARGED FROM THE
PRESSURE RELIEF VALVE. MAINTENANCE IS REQUIRED BEFORE THE SHOWER
CAN BE SAFELY USED.
WARNING: CONSIDERATION SHOULD BE GIVEN TO SUPERVISING THE YOUNG, ELDERLY
AND THE INFIRM WHILST THEY USE THIS SHOWER.
HOW TO USE YOUR
SPA
300C
SHOWER
(DETAILED)

9
WHAT TO DO IF THINGS GO WRONG (2)
SELF HELP
If the shower is not working satisfactorily, make the following checks before calling out the installer.
Any one of these adjustments could restore the performance.
The shower cycles
from HOT to COLD Temperature is set toohot causing the thermal cut-out (safety device) to operate. Turn knob“E” clockwise to increase water flow.
Slowly increase the water temperature by turningknob “E” anti-clockwise until a
comfortable showering temperature has been reached.
WAIT approximately 20 seconds for each adjustment to affect the water temperature.
“ (Medium)” setting may need to be selected.
Water tooHOT Increase water flow by adjusting knob“E” clockwise.
“ (Medium)” setting may need to be selected.
Increase pressure to water supply e.g. fully open service valve or stopcock.
Check hose is not kinkedrestricting the water flow and clean handset.
Water tooCOLD Check power is on by LED indicator beingilluminated.
Decrease water flow by adjusting knob “E” anti-clockwise.
“(High)” settingmay need to be selected.
Select inner or outer only handset spray pattern.
Spray pattern poor Clean the shower handset.
Water takes longer
to heat up Thermal cut-out has operated after previoususe and the LED indicatorhas gone out (automatically resets when unit cools down).
“(High)” settingmay need to be selected.
Water goes cold
while using
shower
Check LED indicator is illuminated.
Check water pressure has not fallen sofar as to let pressure switch cut out,
e.g. Another tap drawingwater off.
Raise position of shower handset.
Broken parts Please contact our spares department on 0870 9000 420 (UK only).
Water continues to
flow when button
“D” pressed to stop
This is normal.
The shower includes a shutdown feature that means the water will continue to flow
for up to7 secondsafter “ (stop)” has been selected.
PROFESSIONAL SERVICE
If the previous “Self Help” checks fail to restore the performance, you should seek professional help.
The person who installedthe shower is probably the best one to investigate and correct it andis certainly the
person to contact if you have had a problem in the guarantee period.
The following additional checklist is provided forthe benefit of the qualified service person.
WARNING: SWITCH OFF THE ELECTRICITY AT THE LOCAL ISOLATOR
BEFORE REMOVING THE COVER TO MAKE CHECKS
Water tooHOT Water flow restrictedby blockage in filterof solenoid valve. Replace solenoid valve.
Water tooCOLD Check circuit through thermal cut-out and/or through pressure switch microswitches.
A schematic wiring diagram is available fromour technical advisory service.
Check each element circuit and check tightness of electrical connections.
No control over
water flow Check control knob is correctly engaged onto the stabiliser valve drive gear. Undo headworks of stabiliser valve.
Check stabiliser is inplace and remove any debrisin valve then re-assemble.
Water discharges
from pressure
relief valve
Check for cause of high pressure and remove it.
Blockage on outlet e.g. blocked shower handset.
Replace the pressure relief disc (not coveredby guarantee).
Water does not
flow when button
“A B C” is pressed.
Ensure that the flying lead from the PCB is connected to the FrontCover.
Check circuit through solenoid coil and/or through pressure switch microswitches.
Possible PCB fault.If defective then replace. Power supply not reaching shower.
WHAT TO DO IF THINGS GO WRONG (1)

10
1. Water is heated instantaneously as it flows
over the heating elements in the copper
cylinder (Diagram 6).
2. The heaters are only switched on when
sufficient water is flowing.
This is done automatically with a switch
which works on water pressure and is
indicated by the LED indicator illuminating.
3. The water is turned onand off by the
solenoid valve and Control PCB built into
the shower.
This is switched on when button “A”, “B” or
“C” is pressed.
4. The flow of water is automatically held at
the level set by the user even though the
supply pressure may vary (see “Effect of
Other Water Devices on Incoming Water
Supply”).
5. If the water supply falls below a set limit, thepressure switch will operate and switch off the
power to the elements. This is indicated by LED indicatorgoing out (see “Effect of Other Water
Devices on Incoming Water Supply”).
6. As a further safeguard, a thermal cut-out switches the power off if the water temperature
climbs above the set limit.
This cut-out, which gives an audible click, may also operate due to residual heat when the shower
is switched off. It will reset itself if water is run through the shower for 10 to 20 seconds.
7. The pressure relief device is to safeguard against abnormalpressure conditions, and provides a
level of appliance protection should an excessive build of pressure occur within the shower.
Effect of Seasonal Incoming Water Temperature Changes
The required water temperature is achieved by adjusting the rate of water flow.
Diagram 7 shows the principle involved in relating temperature rise to flow rate.
The higher the water rate the lower the temperature and vice versa.
The temperature of the water supplied from the mains can vary considerably
throughout the year from 5 to 20°C.
This means that in the winter, flow rate will be less than in the summer to
achieve the same outlet temperature.
In summer the “ (Medium)” power setting may give adequate hot water.
In some winter conditions, it may be necessary to select the inner or outer spray pattern only of
your shower handset. This will ensure correct operation of the shower with a slightly lowerflow rate.
Effect of Other Water Devices on Incoming Water Supply
Your shower is designed to stabilise temperature changes caused by water pressure
fluctuations. These canresult from toilets being flushed or taps being turned on and off.
When this happens your showering temperature will be held within a controlled band, provided that
the minimum pressurerequired by the shower is maintained.
Your shower requires a minimum running
pressure of 69kPa (0.7 bar, 10 psi).
At pressures above 69kPa (0.7 bar, 10 psi) it will minimise temperature fluctuations as detailed
above. If the water pressure falls below 69kPa (0.7 bar, 10 psi) it is likely that the pressure switch
will turn off the power to the heating elements, resulting in a cold shower.
HOW YOUR SPA300C SHOWER WORKS

11
GUARANTEE AND CONTACT DETAILS
CREDA AFTER SALES SERVICE
We offer a technical advisory service on the telephone to installers and other customers with
problems in the field. RING 0870 9000 430 (UK ONLY)
Remember to quote the exact type of shower, as written on the shower front and on is leaflet.
The model and serial number are located on the bottomface of the shower.
Make a note of those numbers here, and be sure to quote them if you call for advice.
Model Number: 53-67_ _ _ _ _ _ _ _ _ _ _ / Serial Number: _ _ _ _ _ _ _ _ _ _ _ _ _ _
Note: You may be charged for a service call if you do not have the serial number.
APPLIED ENERGY PRODUCTS LIMITED, MORLEY WAY, PETERBOROUGH PE2 9JJ
TEL: [phone] / FAX: [phone]
Website: www.creda-showers.co.uk

12
IMPORTANT WARNINGS!
DO NOT SWITCH THE APPLIANCE ON IF YOU SUSPECT IT OFBEING FROZEN.
WAIT UNTIL YOU ARE SURE IT HAS THAWED OUT.
DO NOT OPERATE THE APPLIANCE IF WATER DISCHARGES FROM THE PRESSURE RELIEF
VALVE. MAINTENANCE IS REQUIRED BEFORE THE APPLIANCECAN BE SAFELY USED.
THIS APPLIANCE IS NOT INTENDED FORUSE BY PERSONS (INCLUDING CHILDREN AND
THE INFIRM) WITH REDUCED PHYSICAL,SENSORY OR MENTAL CAPABILITIES,
OR LACK OF EXPERIENCE AND KNOWLEDGE, UNLESS THEY HAVE BEEN GIVEN
SUPERVISION OR INSTRUCTION CONCERNING USE OF THE APPLIANCE
BY A PERSON RESPONSIBLE FOR THEIR SAFETY.
CHILDREN SHOULDBE SUPERVISED TO ENSURE THAT THEY
DO NOT PLAY WITH THE APPLIANCE.
1. Ensure the electricity and water are turned on to the unit.
2.
Your shower can be turned on by pressing either
Button “A”, Button “B” or Button “C”
Button “A” (III) - Starts shower on “High” power.
Button “B” (II) - Starts shower on “Medium” power.
Button “C” (I) - Starts shower on “Cold”.
Press Button “A”, “B” or “C”.
Water will flow and the LED indicator above your choice
will illuminate. It is recommended that you do not wholly
enter the water flow during this period.
3. If the water is not at your desired showering temperature,
turn knob “E” a small amount until you
reach the desired showering temperature.
Turn clockwise for cooler or Turn anti-clockwise for warmer.
4. When you have finished showering, press Button “D” ( ) only, the LED light above will flash
.
Water will continue to flow for up to 7 seconds before switching off.
5. Switch off the electricity supply at the ceiling switch or local isolator.
Notes
•Wait 20 seconds for the temperature to stabilise after each adjustment.
•The LED indicator light illuminates when the heaters are onand, if the shower has
been recently used, can take up to 20 seconds to come on
.
During this time the water may go from very hot to cold before stabilising.
•The position of knob “E” will be approximately the same each time the shower is
used, varying only with incoming water temperature or pressure changes
(e.g. you will only need to change from summer to winter).
•During normal operation, if an overheated water temperature is sensed then the
heater will switch off and the LED indicator light will go out.
Water will continue to flow and cool down before the heater switches back on again.
We offer a technical advisory service on the telephone to installers and
other customers with problems in the field. RING 0870 9000 430 (UK ONLY)
(A3) Leaflet No. 567-2189-61 Revision A
HOW TO USE YOUR SPA300C SHOWER (SUMMARY)