Crestron HD-CTL-101 User manual

HD-CTL-101
8K Smart Display Controller with
HDMI®connectivity
Product Manual
Crestron Electronics, Inc.

The original language version of this document is U.S. English.
All other languages are a translation of the original document.
Regulatory Model: M202116001
Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a
limited nonexclusive, nontransferable Software Development Tools License Agreement. Crestron product operating
system software is licensed to Crestron dealers, CSPs, and end-users under a separate End-User License Agreement.
Both of these Agreements can be found on the Crestron website at www.crestron.com/legal/software_license_
agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed online at www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, please visit
www.crestron.com/opensource.
Crestron, the Crestron logo, Crestron Home, and XiO Cloud are either trademarks or registered trademarks of Crestron
Electronics, Inc. in the United States and/or other countries. Dolby, Dolby Atmos, and Dolby Digital are either trademarks
or registered trademarks of Dolby Laboratories in the United States and/or other countries. HDMI, the HDMI logo, and
High Definition Multimedia Interface are either trademarks or registered trademarks of HDMI Licensing LLC in the
United States and/or other countries. Active Directory is a trademark or registered trademark of Microsoft Corporation
in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in
this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any
proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or
photography.
©2023 Crestron Electronics, Inc.

Contents
Overview 6
Specifications 8
Dimension Drawing 10
Installation 11
In the Box 11
Install the Device 12
Mount on a Wall 12
Mount Under a Table 13
Install in a Rack 14
Connect the Device 15
Configuration 16
Accessing the Web Configuration Interface 17
Action 18
Save Changes 18
Revert 18
Reboot 19
Restore 19
Update Firmware 19
Download Logs 20
Manage Certificates 20
Manage EDIDs 21
Manage Device Drivers 23
Download Configuration 24
Upload Configuration 24
Manage Schedule 25
Status 27
Device 27
Occupancy Sensor 28
Input/Output 29
Network 30
Control System 30
Settings 32
System Setup 33
Occupancy Sensor 36
Inputs 37
Outputs 38
Security 47
Current User 47
Product Manual — Doc. 9366A Contents • iii

Users 48
Groups 49
802.1x Configuration 52
Resources 54
Crestron Support and Training 54
Programmer and Developer Resources 54
Product Certificates 54
iv • Contents Product Manual — Doc. 9366A

v • Contents Product Manual — Doc. 9366A

Product Manual — Doc. 9366A HD-CTL-101 • 6
Overview
The HD-CTL-101 is an 8K Smart Display Controller with HDMI® connectivity that provides a
variety of options for controlling displays without a control processor. Ideal for unified
communications, digital signage, and presentation spaces, the HD-CTL-101 can be configured to
automatically power displays on and off based on schedule, room occupancy, or video sync
detect. The HD-CTL-101 can also be utilized in residential systems to control a variety of devices
such as garage doors and TVlifts.
lDevice control options include CEC, RS-232, IR, Relay, and digital input ports
lAutomatic or scheduled display power on/off
l8K60 4:4:4 signal supported
lHDMI2.1 and HDCP 2.3 compliance
lHDR10, HDR10+, and Dolby Vision® video formats
lProvides RS-232 COM port with software handshaking
lEDIDmanagement
lXiOCloud® service support
lCrestron Home OS®support
lCrestron Driver support
lEnterprise-grade security
lBuilt-in web interface
lPoE(Power over Ethernet) network powered
lNo programming or control processor required
CECControl
CEC (Consumer Electronics Control) can control the source and display devices via the HDMI
connection, potentially eliminating the need for dedicated serial cables or IR emitters, as well as
eliminating the need for a control system. CEC over the HDMI output can also enable the display
devices to be turned on or off automatically.

7 • HD-CTL-101 Product Manual — Doc. 9366A
Device Control via RS-232, IR, Relay, and Digital Input Ports
The HD-CTL-101 includes built-in COM(RS-232), IR, relay, and digital input ports for control
source devices and accessories.
Built-In Web Interface
Full configuration of the HD-CTL-101 can be accomplished using the built-in web interface. To
simplify system installation, the configuration of a single unit can be downloaded to a computer
or mobile device and then uploaded to multiple HD-CTL-101 units.
EDID Management
The HD-CTL-101 provides comprehensive management of EDID (Extended Display Identification
Data) to ensure that every source is displayed at the optimal resolution and format. For
applications requiring a custom configuration, the HD-CTL-101 enables assessment of the
format and resolution capabilities of any device that is connected to the HDMI output. The HD-
CTL-101 provides the ability to configure signals appropriately for the most desirable and
predictable behavior.
8K60 4:4:4 and HDRSupport
The HD-CTL-101 supports video resolutions up to 8K60 with 4:4:4 color sampling. HDR10,
HDR10+, and Dolby Vision® are also supported.
Enterprise-Grade Security
The HD-CTL-101 includes advanced security features and protocols. Using 802.1X authentication,
Active Directory® credential management, PKI authentication, TLS, SSH, and HTTPS, the HD-
CTL-101 provides a true enterprise-grade AV switcher.
XiO Cloud® Service Support
The HD-CTL-101 is compatible with the XiO Cloud service, which is an IoT (Internet of Things)
platform for remotely provisioning, monitoring, and managing Crestron devices across an
enterprise or an entire client base. Built on the Microsoft® Azure® software platform and using
industry-leading Azure IoT Hub technology, the XiO Cloud service enables installers and IT
managers to easily deploy and manage thousands of devices. Unlike other virtual machine-based
cloud solutions, Azure services provide unlimited scalability to suit the ever-growing needs of an
enterprise. For more information, visit www.crestron.com/xiocloud.

Product Manual — Doc. 9366A HD-CTL-101 • 8
Specifications
Product specifications for the HD-CTL-101 are provided below.
Video
Input Signal Types HDMI with HDR10, HDR10+. Dolby Vision™, Deep Color, 8K60 4:4:4 support
(DVIand Dual-Mode DisplayPort™ interface compatible)
Output Signal Types HDMI with HDR10, HDR10+, Dolby Vision, Deep Color, and 8K60 4:4:4 support
(DVIcompatible)
Audio
Input Signal Types HDMI(Dual-Mode DisplayPort interface compatible)
Formats Dolby Digital®, Dolby Digital EX, Dolby Digital Plus, Dolby® TrueHD, Dolby
Atmos®, DTS®, DTS-ES, DTS 96/24, DTSHD® High Res, DTS-HDMaster Audio,
DTS:X®, LPCM up to 8 channels
Connectors
HDMIIN (1) 19-pin Type A connector, female;
HDMI2.1 compliant digital video/audio input (DVI and Dual-Mode DisplayPort
interface compatible)
HDMIOUT (1) 19-pin Type Aconnector, female;
HDMIdigital video/audio output (DVIcompatible)
IN (1) 2-pin 3.5 mm detachable terminal block;
Digital input;
Input Voltage Range: 0–24VDC;
Logic Threshold: ≥2.0VDC 0/low, ≤1.1VDC 1/high;
Input Impedance: 2.2k Ohms pulled up to 5V
COM (1) 3-pin 3.5 mm detachable terminal block;
Bidirectional RS-232 port;
Supports RS-232 up to 115.2k baud with software handshaking
IR (1) 2-pin 3.5 mm detachable terminal block;
IRoutput control port;
Supports IR up to 60 kHz;
IRP2 IR emitter probe sold separately
RELAY1-2 (2) 2-pin detachable terminal blocks;
Comprised of 2 normally open, isolated relays;
Rated 1A, 30VAC/VDC;
MOVarc suppression across contacts
Ethernet 1 (1) 8-pin RJ-45 connector, female;
100BASE-TX/1000BASE-TEthernet port;
Provides network connectivity to secondary device

9 • HD-CTL-101 Product Manual — Doc. 9366A
Ethernet 2 PoE (1) 8-pin RJ-45 connector, female;
100BASE-TX/1000BASE-TEthernet port;
PoE Class 3 powered device (PD) port, 8.2 WMaximum
Ground (1) 6-32 screw, chassis ground lug
Controls and Indicators
PWR (1) LED;
Amber indicates that the device is booting;
Green indicates that the device is operational.
HDMIIN (1) LED;
Green indicates an HDMI signal;
Amber indicates the device is ready for an HDMIsignal.
HDMIOUT (1) LED;
Green indicates an HDMI signal;
Amber indicates the device is ready for an HDMIsignal.
RESET (1) LED indicates the device is being reset.
ETHERNET 1 (2) LEDs on RJ-45 connector;
Green indicates that a 100BASE-TX link is established;
Flashing amber indicates Ethernet activity.
ETHERNET 2 PoE (2) LEDs on RJ-45 connector; Green indicates that a 100BASE-TX link is
established;
Flashing amber indicates Ethernet activity.
Environmental
Temperature 32° to 104°F (0° to 40°C)
Humidity 10% to 95% RH (noncondensing)
Construction
Chassis Metal, black finish, vented sides
Mounting Surface mountable or attachment to a single rack rail
Dimensions
Height 1.20 in. (31 mm)
Width 5.93 in. (151 mm)
Depth 4.09 in. (104 mm)
Weight
0.90 lb (.40 kg)
Compliance
Regulatory Model: M202116001

Product Manual — Doc. 9366A HD-CTL-101 • 10
Dimension Drawing

11 • HD-CTL-101 Product Manual — Doc. 9366A
Installation
Refer to the sections below to install the HD-CTL-101.
In the Box
Qty. Description
1 HD-CTL-101, 8K Smart Display Controller with HDMI® connectivity
Additional Items
2 Mounting bracket (2057072)
4 Screw, Philips, 04-40, 1/4 in. (2007158)
4 Wall anchor, plastic (2043585)
4 Screw, combo head, 06-32, 3/4 in. (2009211)
1 4-pin connector (2003576)
2 2-pin connector (2003574)
4 Washer, steel (2007664)

Product Manual — Doc. 9366A HD-CTL-101 • 12
Install the Device
The HD-CTL-101 can be mounted on a wall, under a table, or on a rack.
Mount on a Wall
To mount the HD-CTL-101 on a wall, follow the instructions below.
1. Using the included 1/4 in. screws, attach the mounting brackets to the device.
2. Using the included anchors and 3/4 in. screws, mount the device to the wall.

13 • HD-CTL-101 Product Manual — Doc. 9366A
Mount Under a Table
To mount the HD-CTL-101 under a table, follow the instructions below.
1. Using the included 1/4 in. screws, attach the mounting brackets to the device.
2. Using wood screws (not included), mount the device to the underside of the table.

Product Manual — Doc. 9366A HD-CTL-101 • 14
Install in a Rack
To install the HD-CTL-101 in a rack, follow the instructions below.
1. Using the included 1/4 in. screws, attach a mounting bracket to the device.
2. Using rack screws (not included), attach the HD-CTL-101 to a rack rail.

15 • HD-CTL-101 Product Manual — Doc. 9366A
Connect the Device
Make connections to the HD-CTL-101 as shown below.
Front Panel Connections
Rear Panel Connections

Product Manual — Doc. 9366A HD-CTL-101 • 16
Configuration
The HD-CTL-101 is configured through a web interface.
This section provides the following information:
lAccessing the Web Configuration Interface on page 17
lAction on page 18
lStatus on page 27
lSettings on page 32
lSecurity on page 47
l802.1x Configuration on page 52

17 • HD-CTL-101 Product Manual — Doc. 9366A
Accessing the Web Configuration
Interface
The first time the web configuration interface is accessed, the user will be asked to set a
username and password. This username and password must be entered to enable access to the
web configuration interface.
To access the web configuration interface:
1. Connect the HD-CTL-101 to the network.
2. Use the Device Discovery tool in Crestron Toolbox™ software to discover the HD-CTL-101
and its IP address on the network.
3. Select Web Configuration in Device Discovery or enter the IP address into a web browser.
4. Enter the username and password, then click Sign In.

Product Manual — Doc. 9366A HD-CTL-101 • 18
Action
The Action drop-down menu is displayed at the top right side of the interface and provides quick
access to common device functionality:
lSave Changes
lRevert
lReboot
lRestore
lUpdate Firmware
lDownload Logs
lManage Certificates
lManage EDIDs
lManage Device Drivers
lDownload Configuration
lUpload Configuration
lManage Schedule
Save Changes
Select Save Changes to save any changes made to the configuration settings.
Revert
Select Revert to revert the device back to the last saved configuration settings.

19 • HD-CTL-101 Product Manual — Doc. 9366A
Reboot
Certain changes to the settings may require the HD-CTL-101 to be rebooted to take effect. To
reboot the device, follow the procedure below.
1. Select Reboot in the Actions drop-down menu. The Confirmation message box appears.
2. Select Yes, Reboot Now to reboot the device. The Reboot message box appears.
3. Wait for the device reboot to complete before attempting to reconnect to the device.
Restore
To restore the HD-CTL-101 to factory defaults, follow the procedure below.
NOTE:When settings are restored, all settings, including the network settings, will revert to
the factory default. If a static IP address is set, restoring the device to factory default
settings will revert the IP address to the default DHCP mode.
1. Select Restore in the Actions drop-down menu.
2. Select Yes in the Confirmation dialog to restore the HD-CTL-101 to factory settings.
Select No to cancel the restore operation.
A dialog is displayed again, indicating that the restore process was successful and that the
device rebooted.
Update Firmware
To update firmware on the HD-CTL-101, follow the procedure below.

Product Manual — Doc. 9366A HD-CTL-101 • 20
1. Select Update Firmware in the Actions drop-down menu.
2. In the Firmware Upgrade dialog, select + Browse.
3. Locate and select the desired firmware file, and then select Open. The selected firmware
file name is displayed in the Firmware Upgrade dialog.
4. Select Load and wait for the progress bar to complete.
5. Select OK. The device with new firmware can now be accessed.
Download Logs
Select Download Logs in the Actions drop-down menu to download the device message logs for
diagnostic purposes. The log file is downloaded to the Downloads folder of the PC.
Manage Certificates
Use the Manage Certificates dialog to add, remove, and manage certificates used in 802.1x and
other protected networks.
Click Manage Certificates in the Actions drop-down menu. The following certificate tabs are
displayed: