Crestron SP-SC User manual

CRESTRON
Operations Guide - DOC. 5729 Contents •• i
Contents
Slide Controller: SP-SC 1
Description 1
Functional Description 1
Physical Description 1
Specifications 2
Setup 3
SP-SC with SmartPresenter™3
SP-SC with SmarTouch™ST-CP 4
SP-SC with CNMSX 5
Programming 6
SmartPresenter™SP-1 6
SmarTouch™ST-CP 6
CNMSX 6
Problem Solving 7
Troubleshooting 7
Further Inquiries 7
Return and Warranty Policies 8
Merchandise Returns / Repair Service 8
CRESTRON Limited Warranty 8

CRESTRON
Operations Guide - DOC. 5729 Slide Controller: SP-SC •• 1
Slide Controller: SP-SC
Description
Functional Description
The SP-SC is a slide controller that allows easy control of slide projectors from the
SmartPresenter, Smartouch ST-CP, and CNMSX systems.
Physical Description
The SP-SC is a small unit with a permanently attached 6 ft. (183 cm) projector cable.
The projector cable is equipped with an EBY, pickle type connector. A 3ft. (91 cm)
Serial Data Cable is supplied for connection to the SmartPresenter or the SmarTouch
ST-CP systems.
SP-SC: Top View

CRESTRON
2•• Slide Controller: SP-SC Operations Guide - DOC. 5729
Specifications
Dimensions: Length 4.850" (123.19 mm)
Width 1.324" (33.63 mm)
Height 1.052" (26.72 mm)
Weight: 6.2 oz. (176 g)
Projector Cable: Connector Type EBY, Five-pin, Pickle
Length 6' (183 cm)
Serial Data Cable¹: Connector Type 3.5 mm, Straight, Stereo
Length 3' (91.44 cm)
Serial Data Cable²: Crestron p/n CNSP-112
12v DC Power Supply*: Crestron p/n PW-1205
(USA and Canada) Input 120V 60Hz 18W Output 12vDC 0.5A
Crestron p/n PWI-1210
(International) Input 230V 50Hz 110mA Output 12V---1.0A 12VA
Software: SIMPL™ Windows®Version 1.20.04 or later
VisionTools Pro™ Version 1.1.3 or later
Crestron Database Version 11.7.207 or later
¹
For SmartPresenter and SmarTouch ST-CP (supplied)
² Required for use with CNMSX (Sold separately)
*
Required for use with SmarTouch ST-CP and CNMSX (sold separately)
4.850"
(123.19 mm)
Cable Length = 6'
(183 cm)
1.052"
(26.72 mm)
1.324"
(33.63 mm)

CRESTRON
Operations Guide - DOC. 5729 Slide Controller: SP-SC •• 3
Setup
SP-SC with SmartPresenter™
Connect the 3.5 mm, Serial Data Cable (supplied) to the input port on the SP-SC.
Connect the other end of the cable to one of the outputs on the SP-1. The EBY, five-
pin, pickle type connector should be plugged into the projector.
To assign a Q-Code for the Slide Controller, refer to the latest revision of the
SmartPresenter – Quick Guide (DOC. 5742).
NOTE: An external power supply is not necessary when using the SP-SC with the
SmartPresenter system.
Connect Serial Data Cable to SP-1
Serial Data Cable
To Slide Projector
Serial Data Cable

CRESTRON
4•• Slide Controller: SP-SC Operations Guide - DOC. 5729
SP-SC with SmarTouch™ST-CP
Connect the 3.5 mm, Serial Data Cable (supplied) to the input port on the SP-SC.
Connect the other end of the cable to one of the outputs on the ST-CP. The EBY,
five-pin, pickle type connector should be plugged into the projector.
To program the ST-CP for the Slide Controller, refer to the SmarTouch STS Wizard
included with VisionTools Pro™or Crestron's SIMPL™Windows®programming
software (v 1.20.04 or later) and the latest version of the Crestron Database (v
11.7.207).
NOTE: An external power supply must be used when using the SP-SC with the
SmarTouch ST-CP system. Refer to "Specifications" on page 2for part number and
input/output voltage specifications.
Connect Serial Data Cable to ST-CP
To Slide Projector
Serial Data CableSerial Data Cable
External
Power Supply
Serial Data Cable

CRESTRON
Operations Guide - DOC. 5729 Slide Controller: SP-SC •• 5
SP-SC with CNMSX
The SP-SC can be used with a variety of Crestron systems, including the CNMSX.
When used with a CNMSX there are additional hardware requirements.
•A specially designed Serial Data Cable is required (p/n CNSP-112).
•An external power supply is required. Refer to "Specifications" on
page 2for part number and input/output voltage specifications.
Connect the stereo plug of the CNSP-112 into the input port of the SP-SC. Connect
the Phoenix type connector to of the CNSP-112 to one of the Infrared – Serial output
ports on the CNMSX.
To program the CNMSX for the Slide Controller, refer to Crestron's SIMPL™
Windows®programming software (v 1.20.04 or later) and the latest version of the
Crestron Database (v 11.7.207).
NOTE: An external power supply must be used when using the SP-SC with the
CNMSX system. A CNSP-112 Serial Data Cable is also required.
Connect to CNMSX
Serial Data Cable
CNSP-112
To Slide Projector
S
G
Serial Data Cable
CNSP-112
External
Power Supply

CRESTRON
6•• Slide Controller: SP-SC Operations Guide - DOC. 5729
Programming
SmartPresenter™SP-1
The SmartPresenter is field programmable and does not require a PC. Refer to the
latest revision of the SmartPresenter – Quick Guide (DOC. 5742). SmartPresenter
software is available, however, it is only necessary for changing drivers, cloning
SP-1 machines, and updating firmware.
SmarTouch™ST-CP
The SmarTouch systems are easily programmed using the SmarTouch STS Wizard.
In several easy steps a SmarTouch system can be programmed and up-loaded. The
STS Wizard is available in VisionTools Pro™software.
SmarTouch systems may also be custom programmed using Crestron's easy-to-use
SIMPL™Windows®and VisionTools Pro™software.
CNMSX
The CNMSX is programmed using Crestron's easy-to-use SIMPL™Windows®
software.
Example Program shown as Block Diagram
This example allows a touchpanel to control a slide projector via the IR-Device (SP-
SC). Feedback is provided to alert the touchpanel user that a button is, in fact, being
pressed. The IR Device represents the driver for the SP-SC. This SP-SC driver can
be located in the Crestron Database (version 11.7.207 or later), under Slide
Controllers.