Crow Arrowhead Elite V6 Operating instructions

Updated 22 – October – 2002
Crow Electronic Engineering
(Australia) Pty Ltd
16
Power Wave
16 Zone Control Communicator
( Ver: 6.20 )
This Manual is Preliminary. Please refer to the
Condensed manual for additional information
Installation &
Programming Guide

Crow Electronic
Engineering
(Australia) Pty Ltd
Corporate Head Office:
429 Nepean Hwy,
Brighton East,
Vic., 3187
Australia
Designed & Manufactured to Meet AS/NZS:4301/93
N345 - Product # CRPW16
Please contact us by Mail, Fax or e-mail.
FAX: [phone]
E-MAIL: [e-mail]
WEB: www.crowaust.com.au
Copyright by Crow Electronic Engineering P/L
June 2002 Power Wave 16 V6.20 and above.
This manual relates to the Crow Power Wave 16 alarm control panel
software version V6.20 and above.
Disclaimer
Crow Electronic Engineering P/L make no warranties regarding the
content of this document and assume no responsibility for any omissions
or errors contained herein.
To the best of our knowledge the information contained in this manual is
correct at the time of printing. Crow Electronic Engineering P/L reserve
the right to make changes to the features and specifications at any time
without notice in the course of product development..

Page 3
CONTENTS
INTRODUCTION.............................................................................................................. 5
Package Contents...................................................................................... 5
Cabinet Details........................................................................................... 6
Input Configurations (Zone Wiring Details) ................................................ 7
Output Specifications ................................................................................. 8
Communication Ports................................................................................. 8
PCB Wiring Instructions ............................................................................. 9
ACCESSORIES (OPTIONAL) ......................................................................................... 15
Receiver Board Installation ........................................................................ 15
Voice Board Installation ............................................................................. 15
DTMF Board Installation ............................................................................ 15
COMMAND CONTROL OPTIONS (REMOTE DTMF & KEYPAD SYSTEM CONTROL) 42
Programming Codes for Arm/Disarm, Output & Mic Control...................... 42
Start of Voice Status Messages for Arm/Disarm & Outputs ....................... 43
Remote Command Control Operation........................................................ 44
Local Command Control Operation............................................................ 45
CONTACT ID CODE & SPEECH PROGRAMMING........................................................ 51
Account Code Numbers............................................................................. 51
Zone Alarm Event Code............................................................................. 51
Manual Fire/Panic/Medical Alarms Event Code......................................... 52
Zone Tamper Alarm Event Codes.............................................................. 52
Assigning Voice Messages to Zone & Manual Alarms............................... 52
CONTACT ID CODE SUMMARY FOR CODES SENT BY THE POWER WAVE ........... 83
CONTACT ID CODES (MOST COMMON CODES) ........................................................ 55
DEFAULTS (RESET PANEL TO FACTORY DEFAULTS).............................................. 42
Reset Various Panel Functions to the Factory Default............................... 42
DELAYS & TIMERS PROGRAMMING............................................................................ 34
Zone Entry Delay Times............................................................................. 34
Area Exit Delay Times................................................................................ 34
Two Trigger Timers.................................................................................... 34
Stay Mode Entry Delay Times.................................................................... 34
Day Zone to Keypad & Output Active Times.............................................. 35
Output Reset Times ................................................................................... 35
Mains Fail and Zone Alarm Reporting Delays............................................ 35
Output On Delay Times.............................................................................. 35
Zone Inactivity & Supervised Radio Times................................................. 35
Output Pulse Times.................................................................................... 35
Door Open Too Long Times....................................................................... 36
DIALLER OPTIONS (MISCELLANEOUS) ...................................................................... 52
Area Arm/Disarm Reporting Options.......................................................... 52
Enabling Various Options to Report........................................................... 53
Keypad & Output Listen-in Options............................................................ 54
Auto– Answer Ring Count.......................................................................... 54
Mains Failure and Zone Alarm Reporting Delays....................................... 54
Upload/Download Security Options ........................................................... 54
DIALLER PROGRAMMING............................................................................................. 46
Enable Dialler & Dialling Parameters........................................................ 46
Reporting Scenarios ................................................................................. 46
Maximum Dial Attempts............................................................................ 47
Telephone Numbers ................................................................................. 47
Telephone Number Prefix (OR PHONE LINE DEBARRING NUMBER) ... 47
Reporting Format for each Telephone Number ........................................ 48
Telephone Number Options...................................................................... 49
Assigning Scenarios ................................................................................ 49
Send Multiple Zone Alarm Reports ........................................................... 51
Automatic Test Call Time.......................................................................... 51
KEYPAD OPTIONS ......................................................................................................... 22
Assigning Keypads to Areas ...................................................................... 22
Keypads Allowed to Arm/Stay/Bypass & Control ....................................... 22
Keypads with Panic/Medical & Fire Alarms Enabled.................................. 22
Various Alarms to Keypad Buzzer Programming ....................................... 22
Entry & Exit Beeps to Keypad Buzzer ........................................................ 23
Keypad LED’s Off when Armed.................................................................. 23
Contents Continued next page

Page 4
CONTENTS Continued
KEYPADS (POWER WAVE-16 VER:6.20 AND ABOVE) ............................................... 10
Display Indications ..................................................................................... 10
Keypad Installation..................................................................................... 11
Addressing individual keypads................................................................... 12
Displaying Memory Events at a Keypad..................................................... 13
OUTPUT PROGRAMMING OPTIONS ............................................................................ 19
Primary Output Options.............................................................................. 19
Special Output Options .............................................................................. 20
Secondary Special Output Options ............................................................ 20
Assigning Time Zones to Turn Outputs On/Off .......................................... 21
Assigning Time Zones to Inhibit Outputs.................................................... 21
PANEL OPTIONS (MISCELLANEOUS).......................................................................... 29
Miscellaneous Panel Options..................................................................... 29
Key-switch and Tamper Options ................................................................ 29
PARTITION PARAMETERS ............................................................................................ 24
Primary Area Based Alarms to Outputs ..................................................... 24
Secondary Area Based Alarms to Outputs................................................. 24
Area Based Arm & Stay Button Options..................................................... 25
Time Zone Auto Arm/Disarm of Areas ....................................................... 25
Special Area Arming and Delay Options.................................................... 25
Area Based Miscellaneous Keypad Options .............................................. 26
Area Based Special Options ...................................................................... 27
Area Based Dialler Reporting Options ....................................................... 28
PROGRAM ADDRESS (LOCATION) SUMMARY........................................................... 56
PROGRAM MODE (ACCESSING FOR THE FIRST TIME)............................................. 16
Accessing Installer Mode from Power-up................................................... 16
Accessing both Program Modes from Normal Run Mode .......................... 16
How to Program your Power Wave-16....................................................... 16
How to Reset the Panel back to Factory Defaults...................................... 16
Exiting Program Modes.............................................................................. 17
RADIO (WIRELESS REMOTE CONTROL) USER KEY PROGRAMMING..................... 37
Enrolling Radio Keys.................................................................................. 37
Assigning a Radio Key Type ...................................................................... 37
Assigning Area & Arm Disarm Options to Radio Keys ............................... 37
Assigning Output & Panic functions to Radio Keys.................................... 38
Assigning Radio Keys to Outputs............................................................... 39
RADIO (WIRELESS ZONE) DETECTION DEVICE PROGRAMMING............................ 36
Enrolling Radio Zones................................................................................ 36
Assigning Radio Zone Options................................................................... 36
SETUP & DIAGNOSTIC DATA (MISCELLANEOUS) ..................................................... 41
Temporary Output Disable ......................................................................... 41
Clear Output Defaults................................................................................. 41
Data Transfer using EE² Board .................................................................. 41
Dynamic Data e.g. Keypad Address, Panel Software Version ................... 41
Start Printing the Event Memory Buffer...................................................... 41
Start Walk Test Mode................................................................................. 42
TIME / DATE & TIME ZONES PROGRAMMING............................................................. 39
Setting the Real Time Clock....................................................................... 39
Daylight Savings Adjustments.................................................................... 40
Time Zone Programming ........................................................................... 40
USER CODE PROGRAMMING ....................................................................................... 17
Programming User Codes.......................................................................... 17
User Code Options..................................................................................... 18
Assigning Time Zone Control to Users....................................................... 18
Programming the Installer Code................................................................. 19
Duress Digit................................................................................................ 19
WARRANTY ( LIMITED / CONDITIONS APPLY - READ CAREFULLY )....................... 84
ZONE PROGRAMMING .................................................................................................. 30
Soak Test Zones........................................................................................ 30
Zone Vibration Settings.............................................................................. 30
Single or Dual Zone Input (8 or 16 zones) ................................................. 30
Input is a Short or EOL Monitored.............................................................. 30
Zone Response Time................................................................................. 31
Low Zone Program Options (Zones 1-8).................................................... 31
High Zone Program Options (Zones 9-16)................................................. 32
4+2 PROGRAMMING ...................................................................................................... 55
Programming Special Characters for 4+2.................................................. 55

Page 5
INTRODUCTION
This Arrowhead Elite Version V6 alarm control panel has been designed to provide the most requested features for
both the installer & the end-user. These features include ease of installation, ease of programming and user friendly
operation all in a package which is reliable, functional and attractive.
Utilising many years of experience in the security industry and implementing valuable feedback, we are proud to
provide you with a new generation of alarm controller. The Elite V6 is a New Zealand designed and built product
which brings you the quality and features which you deserve at an affordable price. In addition to the advanced
design, only the highest quality components have been used in the production of this Elite panel to ensure the
highest degree of reliability.
This manual will guide you through the installation and programming of your Elite alarm panel. For additional
information regarding the operation instructions and options, please refer to the enclosed “Elite User’s Guide”.
PACKAGE CONTENTS
This Crow Power Wave-16 package should contain the following items;
1 x Power Wave-16 Controller PCB
1 x Power Wave-16 new generation backlit keypad
1 x Power Wave-16 keypad zone list
1 x Power Wave-16 Users Guide
1 x Power Wave-16 cabinet & lid
1 x Cabinet hardware accessory pack including,
1 x Spare 1.5a fuse
1 x Cabinet tamper switch
1 x Tamper switch wire set
1 x Battery lead set
2 x Cabinet lid screws
10 x 2k2 (red, red, red) end of line resistors
10 x 4k7 (yellow, purple, red) end of line resistors
10 x 8k2 (grey, red, red) end of line resistors
If any of these items are missing from this package, please contact your nearest Crow stockist where you purchased
it from.

Page 6
MOUNTING
KEYHOLES
CABLE ENTRY
Insert Tamper
MAINS
TRA NSFORMER
Install Battery
Here
TAM P E R AS S E M B LY
MAIN CONTROL CABINET
BLOCK
Assembly
Here
CABINET DETAILS

Page 7
INPUT CONFIGURATIONS (ZONE WIRING DETAILS)
The Elite V6 has 10 separate programmable monitored analogue inputs,
8 x Programmable, multi-state detection inputs
1 x Programmable tamper input
1 x Programmable key-switch input
Each input must be terminated with a short or the appropriate combination of end-of-line resistors,
depending upon the programmed configuration.
ZONE INPUTS - Each of the 8 zone inputs can be independently assigned one of the following configuration options;
Type 1(8Z) 8 Zone Short circuit input NO-End-of-Line (EOL).
Type 2(8Z) 8 Zone Single-End-of-Line 2k2 (EOL) with no tamper.
Type 3(16Z) 16 Zone Double-End-of-Line (EOL) No Tamper.
Type 4(16Z) 16 Zone Double-End-of-Line (EOL) With open & short circuit Tamper.
The following table shows end-of-line resistor configurations. The reference to LEDS in bold below relate to the
program option setting at addresses P410E & P419E. The options 1-8 at addresses P410E & P419E relate to zone
inputs 1-8. If an input is set to EOL at address P419E then it relates to the single zone being a 2K2 resistor but if
zone doubling is turned on for the same input (P410E LED On) then EOL means that the tamper resistor is 2K2.
Zone Type Low Zone Hi Zone Tamper
Type 1(8 Zone No EOL)
P410E LEDS Off, P419E LEDS Off
N / A (Short circuit)
[ No Resistors Required ]
None
[ N / A ]
None
[ N / A ]
Type 2(8 Zone EOL, No Tamper)
P410E LEDS Off, P419E LEDS On
2k2
(Red, Red, Red, Gold)
None
[ N / A ]
None
[ N / A ]
Type 3(16 Zone EOL, No Tamper)
P410E LEDS On, P419E LEDS Off
4k7
(Yellow, Purple, Red, Gold)
8k2
(Grey, Red, Red, Gold)
None
[ N / A ]
Type 4(16 Zone EOL, with Tamper)
P410E LEDS On, P419E LEDS On
4k7
(Yellow, Purple, Red, Gold)
8k2
(Grey, Red, Red, Gold)
2k2
(Red, Red, Red, Gold)
LED at Address P410E
(Zone Doubling)
ª
LED at Address P419E
(EOL or Tamper)
ª
LED # 1
Off = Zone 1 only
On = Zones 1 & 9
LED # 1
Off = No EOL
On = Zone EOL or Tamper
LED # 2
Off = Zone 2 only
On = Zones 2 & 10
LED # 2
Off = No EOL
On = Zone EOL or Tamper
LED # 3
Off = Zone 3 only
On = Zones 3 & 11
LED # 3
Off = No EOL
On = Zone EOL or Tamper
LED # 4
Off = Zone 4 only
On = Zones 4 & 12
LED # 4
Off = No EOL
On = Zone EOL or Tamper
LED # 5
Off = Zone 5 only
On = Zones 5 & 13
LED # 5
Off = No EOL
On = Zone EOL or Tamper
LED # 6
Off = Zone 6 only
On = Zones 6 & 14
LED # 6
Off = No EOL
On = Zone EOL or Tamper
LED # 7
Off = Zone 7 only
On = Zones 7 & 15
LED # 7
Off = No EOL
On = Zone EOL or Tamper
LED # 8
Off = Zone 8 only
On = Zones 8 & 16
LED # 8
Off = No EOL
On = Zone EOL or Tamper
Type 1 (8 Zones, Short Circuit)
n/c
Type 2 (8 Zones, 2k2 EOL, No tamper)
n/c
n/o
2k2
Type 3 (16 Zones, 4k7 & 8k2 EOL with No tamper)
A lar m Co nt ac t
n/c or n/o
4k7
A lar m Co nt ac t
n/c or n/o
8k2
Type 4 (16 Zones, 4k7 & 8k2 EOL , 2k2 EOL for tamper)
2k2
Tamper
A larm Contac t
n/c or n/o
4k7
A larm Contac t
n/c or n/o
8k2
Tamper

Page 8
INPUTS Cont.
KEYSWITCH - This input can be used to control the panel via a key-switch, digital keypad or similar. This is a
multi-state input which can be end-of-line configured in the same way as the 8 zone inputs. These multiple end-of-
line configurations will produce either arm/disarm or stay mode on/off on an individual area basis.
TAMPER - A 24Hr tamper circuit is available for monitoring tamper status of detectors, junction boxes, cabinets
and satellite sirens etc. This Tamper circuit is programmable with 2 options (P311E1E) either normally closed loop
or 2k2 EOL supervision. The tamper circuit must be terminated with an end-of-line resistor if 2k2 EOL supervision
is selected. The activation events to outputs for this tamper circuit are fully programmable.
AC - Connect the two low voltage wires (no polarity) from the transformer to the terminals marked AC on the Elite
PCB. The Elite box includes a transformer rated at 1.4 amps at 17 volts AC and incorporates an inbuilt thermal
protection fuse.
EARTH - Always connect the mains earth to the steel cabinet via the appropriately marked terminal on the mains
terminal block in the steel cabinet. Also connect a lead from this earth point to the terminal marked "Earth" on the
Elite PCB.
BATTERY - Connect a sealed lead acid rechargeable 12V DC battery to the battery terminals via the red and black
battery leads supplied. The minimum recommended battery capacity is 7 amp hours. Battery charge current at
these terminals is limited to a maximum of 300ma.
LINE IN - This pair of terminals is used to connect the Elite to the incoming telephone line from the street. The
Dialler uses this line for reporting alarm events.
LINE OUT - This pair of terminals is used to connect telephones and other communication equipment to the
incoming phone line via the Elite controller. The telephone line is passed through the Elite controller to ensure that
the line is available to the controller when it is required.
OUTPUTS
12 VOLT OUTPUTS - There are four 12V DC outputs available on the Elite PCB. They are fuse protected suitable
for powering detectors, sirens and other external devices. These outputs are marked 12v and 0v (or POS & NEG at
the keypad buss), and are supplied by fuses F1 and F2. A maximum total load of 1 amp may be drawn from these
terminals.
OUTPUTS 1 & 2 - These fully programmable, high current, open collector (high-going-low) type FET outputs
capable of switching up to 1.5A @ 12V DC. These 2 outputs are normally set as switched outputs, providing power
for 12v sirens or piezos. However If options 2 or 3 are turned Off at address P310E (2 relating to output 1 and 3
relating to output 2) then the output becomes a siren output designed to drive an 8 ohm 10 watt horn speaker with a
modulated siren tone. Also if a horn speaker is connected to Output 1 you may select the listen-in feature to
this output at address P313E as well so that the dialling sequence can be heard at the speaker.
OUTPUT 3 - This is a low current, open collector (high-going-low) type output capable of switching no more than
500ma. Like Outputs 1 & 2 it is fully programmable.
OUTPUTS 4,5,6,7&8 - These are low current, open collector (high-going-low) type outputs capable of switching no
more than 100ma. Like Outputs 1 & 2 they are fully programmable.
NOTE: - Connecting devices which draw current in excess of 100ma to outputs 4,5,6,7&8 may cause
permanent damage to the Elite controller output concerned.
COMMUNICATION PORTS
KEYPAD PORT - The terminals marked POS, NEG, CLOCK, & DATA make up the communications port which the
keypads and other intelligent field devices use to talk to the Elite controller. The terminals are connected to
corresponding terminals on the remote devices. The "listen" terminal is only used by the keypads and utilises a fifth
wire to provide a dialler listen in facility. This feature is particularly useful when servicing monitoring faults.
SERIAL PORT - The serial port is for the connection of the RS232 serial board, the optional VOICE or DTMF
Boards, or the DTU (data transfer) board. The serial board allows for printing of the 255 event buffer to a serial
printer or for PC direct up/down load connection. The VOICE board allows for alarm reporting and remote control
with speech messages, the DTMF board allows for remote control using tones, both from a remote telephone. The
DTU board to allows program back-up and re-instatement.

Page 9
Listn.
Data
Clock
Neg
Pos
Mode 3 (Type 600) Plug And Wall Socket Wiring;
Before calling Crow tech. Support or your supplier
Re: Phone Line or Dialler reported issues, please ensure
that the Mode-3 socket on the wall is wired as per below.
********** Observe Line In / Out Polarities **********
Terminal 6 = Tip-In = “ + ” side of Line-In from Street
Terminal 2 = Ring-In = “ -” side of Line-In from Street
Terminal 5 = Tip-Out = “ + ” side of Line-Out to Int. Phones
Terminal 1 = Ring-Out = “ -” side of Line-Out to Int. Phones
AC
Outputs
PCB WIRING INSTRUCTIONS
com
Battery
com 1&9 2&10 3&11 4&12
0V
Tmp 0V 12V
Heatsink
Serial Socket
Red
Blk
+ _
Optional (5th wire) Listen-in Keypad Connection
Passive Infra-
Red Detector
Tmp Tmp N/C Com 0V 12V
2k2
+
_
Internal Alarm-Piezo
Crow Power
Wave-16 / Ver6.20
12v
0v
2k2
Latching Smoke Detector with
Normally Open Contacts
3A
F3
1.5A
F2
1.5A
F1
Telephone Line Connections
0V
12
1 32 4 5 6 7 8
5&13 com 6&14 7&15 com 8&16 com Key 12V
Ext Siren Box with
Siren/Strobe/Tamper.
+
_
+
_
2k2
Panel Tamper
AC
17V
2k2
2k2 2k2 2k2 2k2 2k2
16VAC
1.5Amp
Mains Earth
From Power
Pack
RJ11
Phone
Socket
In
Out
From ‘ + ’
Street ‘ - ’
To ‘ - ’
Phone ‘ + ’
Line Out (‘ + ’)
To Phones
( Tip-Out )
Line Out (‘ - ’)
To Phones
( Ring-Out )
Line In
From
Street
‘ + ’ Tip-In
‘ - ’ Ring-In
P/Wave-16
Keypad
Wireless Receiver “Bit” set jumper.
On = 24 Bit / OFF = 40 Bit
( Leave OFF (on 1 pin only) for any type of
Crow Wireless Product, since Crow
products are 40 Bit setting compatible).
Pos
Neg
Clock
Data GndAnt
RX-16 / 40
303 or 433 MHz
Wireless Receiver

Page 10
When the Elite keypad is displaying numeric values in program mode it uses the zone LEDS 1-8 to indicate a
value of 1-8 and to maintain consistency with the 8 zone LED keypad, the panel uses the “A” LED to indicate a
“0” and the “B” LED to indicate a “9”.
“A” = 0, “B” = 9.
LIGHT OFF ON STEADY FLASHING
BATTERY Normal System Back-up Battery Low
MAINS Normal Mains Power Off
ARMED Unused Unused Unused
MEMORY Normal Memory Display New Event to View
BYPASS Normal Bypass Mode Active Zone(s) Bypassed
PROGRAM Run Mode Client Program Mode Installer Program Mode
TAMPER Normal Tamper still Active New Tamper Alarm
LINE Normal Communicating Line Fail or no Kissoff
AUX. Unused Unused Unused
CONTROL Control Function Off Control Function On DOTL Override On
ZONES 1-16 Zone Secure Zone Violated Zone in Alarm
A Partition A Disarmed Partition A Armed Partition A in Stay Mode
B Partition B Disarmed Partition B Armed Partition B in Stay Mode
C Partition C Disarmed Partition C Armed Partition C in Stay Mode
D Unused Unused Unused
1
2
3
4
5
6
7
8
Armed
Memory
Bypass
Program
Aux
Mains
Battery
Tamper
Line
Control
Elite AB
9
10
11
12
13
14
15
16
CD
16 Zone Power Wave - 16 LED Keypad Window Layout
ELITE KEYPADS

Page 11
KEYPAD FUNCTIONS
The Elite LED Keypad consists of; an 18 button, backlit silicone rubber keypad, 30 LED indicators and an internal
piezo buzzer housed in a modern white plastic housing. The plastic housing has a hinged front lid to cover and pro-
tect the rubber buttons when not in use. All the electronics are contained on a single circuit board inside the housing.
Because the keypads communicate with the controller using data, the cable run from panel to keypads is secure
against tampering. For this reason there is no tamper switch on the keypad assembly. Access to the keypad electron-
ics will not disarm the panel.
BUTTONS
The 18 silicone rubber buttons are used for the following functions;
a-In normal operating mode the numeric keys are used for entering Access Codes. In Program Mode the
numeric keys are used for entering program addresses & new values.
b-The buttons with text labels are used as function buttons and select the options indicated by the text and
normally precede other button presses, e.g. to enter Bypass Mode press <BYPASS> and a two digit
numeric key entry corresponding to the zone number you wish to be excluded eg “01” for Zone # 1, “09” for
Zone # 9 and “15” for Zone # 15.
c-The PROGRAM Key is used to prefix option selections in the program modes e.g. <PROGRAM> 24
<ENTER> selects User Code 24 when in either of the two program modes. The PROGRAM key is also used
prior to a Master or Installer Code to enter one of the program modes from normal operating mode.
d-The ENTER Key is used after entry of a sequence of numbers (eg entry of a User code to Arm or Disarm
the system). As a User code can be 1-6 digits in length, the panel will not accept a code entry until the Enter
key is pressed.
e-The CONTROL button, if enabled, is used to either turn an output on/off or disable the Day Mode alarms.
The control output can be used to operate other external devices such as garage door openers, door locks,
lights, etc.
LED INDICATORS
The LED indicators are used to display system conditions including Zone status, Battery state, Tamper etc. Please
refer to the LED table on page 13 for a full explanation of the conditional displays.
KEYPAD INSTALLATION
Separate the two keypad halves by carefully inserting a small screwdriver into the release slots on the bottom edge
of the keypad front half and applying a gentle pressure. This will release the bottom edge of the housing enough for
you to unclip the top.
Screw the base to the wall using the mounting holes provided. These holes will match the standard single switch
plate spacing. Ensure the base is mounted right side up. It is marked with the word "TOP" to aid orientation. When
fixing the base to the wall make sure the top of the screw heads will not touch or short out the underside of the PCB
when the top half of the keypad is reinstalled. Bring the cables through the centre of the base.
Connect the 4 or 5 wires to the 5 way terminal block on the rear of the keypad PCB making sure to match the cables
up with the terminals as marked on the control panel's keypad port. The 5th wire is connected from the "LIN" terminal
of the keypad to the "Listen" terminal of the Elite PCB keypad port.
Once the cables have been terminated and the required address allocated (see page 12) clip the front half of the key-
pad onto the base by first engaging the clips at the top edge and then close the front down and clip it in at the bottom.
Now stick the zone list provided to the inside of the hinged lid.
WIRING
The Elite keypad connects to the Elite Controller via a 4 or 5 wire data & power connection. A maximum of 8 LED
keypads can be connected, each wired in parallel. It is advisable that each keypad has a separate cable run from the
keypad to the control panel. If the cable runs are short distances it is possible to connect two keypads at the end of
one cable run but we don’t recommend this. A 5th wire may be used to provide a "Listen-in" facility at the keypad.
The maximum recommended cable length using standard 0.2mm² security cable is 50m. Cable runs exceeding this

Page 12
distance may require 0.5mm² cable. Always use good quality cable. Some installations may require data cable to en-
sure data integrity in noisy sites.
KEYPAD TAMPER (wrong code alarm)
A wrong code or Keypad Tamper alarm is generated by the Elite after 4 consecutive invalid code entries. The con-
troller will not “Lock-Out” the keypad at this point but simply create an alarm condition that may be reported to a
monitoring company via the dialler. Entry of a valid user code will reset the Keypad Tamper alarm, however, the
alarm event will be written into memory and the keypad memory light will be flashing indicating the presence of a new
memory entry.
Each of the 8 possible LED keypads which are able to be connected to
your Elite panel must be addressed individually to avoid BUS conflicts and
other communication problems. As default, each keypad comes ad-
dressed as #1 with all links intact.
Use the table to the left to detevmine which links to cut to assign the cor-
rect address to the keypads you are installing, e.g. To assign a keypad as
address #2, you must cut link A only. To assign a keypad as address # 4,
you must cut link A&B.
When cutting address links it is important to make a clean cut between the
link blocks as shown below. Links can be restored by soldering across the
effected pads.
IMPORTANT NOTE: KEYPAD ADDRESS CHANGES ARE ONLY REC-
OGNISED AT POWER-UP. ALL CHANGES SHOULD BE MADE IN THE
POWERED DOWN STATE AND THEN ON POWER-UP THE NEW KEY-
PAD ADDRESS WILL BE RECOGNISED BY THE PANEL.
Keypad
Address
Address
Links
# A B C
1
2 X
3 X
4 X X
5 X
6 X X
7 X X
8 X X X
Xdenotes link is cut
A B C D cut here
ADDRESSING ORIGINAL (CUTTING LINK) TYPE KEYPADS
1 2 3 4 5 6 7 8
On
Off
Switch '1' Switch '2' Switch '3'
Keypad 1 Off Off Off
Keypad 2 On Off Off
Keypad 3 Off On Off
Keypad 4 On On Off
Keypad 5 Off Off On
Keypad 6 On Off On
Keypad 7 Off On On
Keypad 8 On On On
Panel Switch '5' Switch '6' Switch '7'
PW-4 Off Off Off
PW-8 On Off Off
PW-16 Off On Off
PW-64 On On Off
Switch '8'
Disable Tamper On
Enable Tamper Off
Addressing new LCD Keypads
Addressing new Icon Keypads
NOTE:
ONLY the latest (Series-6) Icon (LED
Type) and the newer LCD (Ver:1.04)
type keypads are compatible with this
(Ver:6.20) panel. The keypads from the
previous (Ver:5.xx) panel are NOT
compatible with this (Ver:6.20) panel.
D C B A
Keypad 1 On On On
Keypad 2 On On Off
Keypad 3 On Off On
Keypad 4 On Off Off
Keypad 5 Off On On
Keypad 6 Off On Off
Keypad 7 Off Off On
Keypad 8 Off Off Off
Tamper Disable
D C B A
Tamper Enable
D C B A
Keypad 1
default
D C B A
Off
On
Off
On

Page 13
VIEW MEMORY MODE
This Elite alarm panel has an event memory which stores the most recent events, (up to 255), including all alarm
events, all system events such as mains failure etc as well as arming by Area. This event memory is displayed via
the standard keypad with the most recent event shown first and subsequent events following in descending order
from newest to oldest.
The "MEMORY" light will flash on and off when there is a new event in memory which has not been viewed. To
stop the "MEMORY" light flashing, simply press the MEMORY button and the event memory will be flashed back to
you with the most recent event shown first. To cancel the memory display just press “ENTER”. Each event is
separated by a beep tone. The memory light will also stop flashing when the system is armed.
Current System Alarms
When viewing the memory event buffer at the keypad by pressing the “MEMORY” button, the first thing that will
always be displayed is the Current System Alarms that are still present. The Current System Alarms are indicated
by the Memory/Mains & Battery LEDS being on plus a zone LED from 1-8 to indicate the system alarm/s present. If
no Zone LED’s are on at this time, it means that there are no current system alarms. If a zone LED or LED’s are On
then this indicates system alarms that have not yet cleared. The zone LED’s 1-8 are pre-defined as to what system
alarm they will display. These system alarm indications are shown in the table below. Following the display of
current system alarms the panel will then sequence through the 255 historical memory events starting at the most
recent event. The second table shows the alarm events that can be displayed in memory mode and what indicators
are used to show them.
HISTORICAL EVENT DISPLAY CHART
EVENT DEVICE INDICATOR STATUS
ACTIVATION Zones 1-16 LED's 1-16 On Steady
BYPASS Zones 1-16 BYPASS
LED's 1-16
On Steady
On Steady
DETECTOR TAMPER
(SHORT CIRCUIT)
Zones 1-8 TAMPER
LED's 1-8
Flashing
On Steady
DETECTOR TAMPER
(OPEN CIRCUIT)
Zones 9-16 TAMPER
LED's 9-16
Flashing
On Steady
CABINET TAMPER Cabinet or Satellite Siren TAMPER Flashing
WRONG CODE ALARM
Code Tamper at
Keypad #
TAMPER
LED’s 1-8
On Steady
On Steady
CROW KEYPAD TAMPER SWITCH
ACTIVATED
Keypad Tamper Alarm at
Keypad #
TAMPER
LED’s 1-8
On Steady
On Steady
LOW BATTERY Controller Battery BATTERY Flashing
MAINS FAILURE Controller Mains Supply MAINS Flashing
FUSE FAILURE (F1 or F2) Controller on-board fuses MAINS Flashing
LED # 1 Battery Low LED # 5 Radio Pendant Battery Low
LED # 2 Mains or 12V Fuse Failure LED # 6 Supervised Detector Failure
LED # 3 Telephone Line Failure LED # 7 Zone Inactivity Timeout
LED # 4 Radio Detector Battery Low LED # 8 Dialler Kiss-off Failure
CURRENT SYSTEM ALARMS

Page 14
VIEW MEMORY MODE Continued;
HISTORICAL EVENT DISPLAY CHART-Continued
EVENT DEVICE INDICATOR STATUS
LOW BATTERY-ZONE Radio Zone
Zone 1-16
BATTERY
LED's 1-16
Flashing
On Steady
LOW BATTERY-PENDANT Radio Key
User 1-20
BATTERY
LED's
1-16,17,18,19,20
Flashing
On Steady
ZONE INACTIVITY TIMEOUT Zone 1-16 LED’s 1-16
TAMPER
CONTROL
On Steady
Flashing
Flashing
SUPERVISED RADIO TIMEOUT Zone 1-16 LED’s 1-16
TAMPER
BYPASS
On Steady
Flashing
Flashing
DURESS ALARM Duress Alarm
(at Keypad #)
TAMPER
LINE
LED’s 1-8
Flashing
Flashing
On Steady
KEYPAD PANIC Panic Alarm at Keypad LINE
LED’s 1-8
Flashing
Flashing
KEYPAD FIRE Fire Alarm at Keypad LINE
CONTROL
Flashing
Flashing
KEYPAD MEDICAL Medical Alarm at Keypad LINE
BYPASS
Flashing
Flashing
ARMED Area "A" Armed "A" On Steady
ARMED Area "B" Armed "B" On Steady
ARMED Area "C" Armed “C” On Steady
STAY MODE ON Area "A" in Stay Mode "A" Flashing
STAY MODE ON Area "B" in Stay Mode "B" Flashing
STAY MODE ON Area "C" in Stay Mode “C” Flashing
TELEPHONE LINE FAIL Panel Dialler LINE On Steady
EXCESSIVE RE-TRIES Panel Dialler LINE
LED 1
On Steady
On Steady
FAILURE TO GET A KISSOFF Panel Dialler LINE
LED 2
On Steady
On Steady
WALKTEST MODE Manual Walk-test Mode MAINS
BATTERY
LINE
LED’s 1-16
On Steady
On Steady
On Steady
On Steady

Page 15
OPTIONAL ACCESSORIES
INSTALLATION OF RX-16 RECEIVER
The Elite V6 has a high level interface with the RX-16 radio receiver. The addition of this receiver will add wireless
capability to your system in the form of wireless PIR detectors, Wireless Radio-key transmitters and wireless reed
switch transmitters. The RX-16 receiver connects to the same communications port as the keypads and can be
installed , either inside the cabinet, or if preferred, may be installed at a remote location. The RX-16 is available in 2
frequencies, 303.875mhz or 433.92mhz. Multiple RX-16 receivers may be connected to the panel to increase the
effective range if required.
The RX-16 receiver requires 4 cores and can successfully be connected via 0.2mm² unscreened cable over a
distance of up to 100metres. Like the keypads the RX-16 has 12v and 0v terminals for connection to the 12v supply
and CLK and DATA terminals for connection to the communications bus.
The green LED fitted to the RX-16 receiver will indicate when the unit is in "Learn" mode (LED Flashing) or when it is
receiving an actual radio transmission (On Steady)
INSTALLATION OF VOICE or DTMF BOARD
The Elite V6 can also be fitted with a 90 second Voice Board or DTMF module. The Voice board stores either alarm
event messages for Voice dial monitoring and /or status messages for use with Command Control. The DTMF board
provides decoding of keypad numeric entries from a remote telephone. The Elite V6 Voice or DTMF Boards are
installed directly onto the motherboard via the "SERIAL" socket.
Installation procedure for the Voice or DTMF Board module is as follows.
1 Power-down the Elite fully before starting the installation procedure.
2 Carefully plug the Voice or DTMF Board into the SERIAL socket.
3 Power-up the Elite.
Once you have installed the Voice Board you can record your personalised speech messages into the module with
the speech programmer. The programmer plugs onto the 10 way strip connector on the voice board.
To record your messages once the programmer is installed, first press the reset button on the side of the Voice
Board, then hold the programmer about 10 cm away from the mouth and speak clearly at normal level into the
microphone while holding down the "REC" button. When you reach the end of your message release the REC
button. (NOTE: Each individual message must be longer that 2 seconds duration). When recording your voice alarm
message, you must ensure that you clearly identify the origin of the call. You can play the message back through the
programmer by first pressing the reset button then by pressing the "PLAY" button momentarily. Because the Elite V6
can address many individual voice messages you must store individual messages at what is known as recording
slots within the Voice Board. These recording slots are recorded sequentially, one message starting where the other
finishes. Every time you press and release the REC button on the programmer, you create an end of message
marker. These markers are used to define the recording slots within the Voice Board and can be of varying length
according to each message duration.
To re-record your messages you must first press the "RESET" button on the speech module to get back to recording
slot #1. Once you are at slot #1 you can re-record your messages in order as required.
NOTE: When recording multiple messages you only press the “RESET” button once at the beginning then record all
messages sequentially as stated above. When you have finished recording all of your messages you can then press
the “RESET” button to allow play-back of the recording messages for verification purposes.
When you have finished recording your alarm messages, unplug the programmer and the process is complete.

Page 16
ACCESSING PROGRAM MODE FOR THE FIRST TIME
GENERAL INFORMATION
There are two program modes in the Elite panel. The first is the “Client” Program Mode to allow a system User to
Add, Change or Delete User Codes.
The second mode is the “Installer” Program Mode. The Installer Program Mode allows ALL programmed data to
be changed. Access to both Modes is described below.
ACCESS TO INSTALLER PROGRAMMING ON POWER UP
When power is applied to the controller for the first time, with the panel tamper input open and none of the
Areas either fully Armed or in Stay mode, the panel will inhibit tamper alarms and ready the panel to enter
INSTALLATION PROGRAM Mode (unless the Installer Lock-out option P310E7E has previously been enabled). At
this point you can go to any keypad which is connected to the panel and;
Press –”PROGRAM”-”ENTER”
which will automatically put that keypad into Installation Program mode, Program LED Flashing. (NOTE: Only one
keypad can be in Program mode at any time)
ACCESS TO PROGRAM MODES FROM RUN MODE
Before you can enter program mode from the normal Run Mode, the panel must be disarmed and not in stay mode.
Then;
Press <PROGRAM> - <Code 1 (or Master Code)> - <ENTER>
Program light steady
Note: Default Master Code (Code 1) is 1,2,3
You are now in Client Program Mode. When you are in Client programming mode you have access to program
addresses P1E to P50E (user code programming). To Enter Installer Program Mode from Client Program Mode;
Press <PROGRAM> - <Install Code> - <ENTER>
Program light flashing
Note: Default Installer Code (P249E) is 0,0,0,0,0,0
By default the installer can go directly to Installer Program Mode from Normal Run mode provided No Areas are
Armed or in Stay Mode. The Installer Mode direct option can be disabled at address P310E Option 6.
HOW TO PROGRAM YOUR ELITE
The programming sequence always follows this pattern once you have accessed one of the Program Modes;
<PROGRAM> - <1,2,3 or 4 digit address> - <ENTER>
3 short beeps if OK - 1 long beep if error
The LED’s will display current value or status
Enter the new value or option
<New Value> - <ENTER>
3 short beeps if OK - 1 long beep if error
An example of programming is shown below. Here we are programming User Code 23 (P23E) with the code
number of 2580.
P 23 E 2,5,8,0 E
In this example the <P> represents the PROGRAM key, <23> represents the actual program address, 2580 is the
data and <E> represents the ENTER key.
TO CLEAR PROGRAM INFORMATION (From Installation Mode Only)
There are multiple options available for clearing program information (Reset to
defaults). These are detailed on page 41.

Page 17
e.g. To reset User Codes 1-50 (P 840E)
Press <PROGRAM> - 840 - <ENTER>
3 beeps - Program light flashing
After resetting the various defaults, all options associated with that function (eg User Code Defaults P840E) will be
set to the default values shown in the Program Summary at the rear of this manual. The default settings have been
chosen to simplify the installation process by minimising the amount of programming necessary to get the system
fully functional.
TO EXIT PROGRAM MODES
To exit program modes when you have finished programming:
Press <PROGRAM> - <ENTER>
Program light goes out
The panel is now back in normal Run Mode, any program changes you have made will have replaced previous
values and be in effect.
Note: During programming Tampers and 24 hour alarms are disabled which allows quiet access to the panel,
detectors and satellite siren units etc. On exiting program mode, all inputs are scanned and if any tampers or 24Hr
alarms are present an activation will occur.
Note: Where there are multiple options at one address, the numbers “0” & “9” have been reserved. Entering
a “0” at the address will turn all options OFF at that address whereas entering a “9” will turn all options ON
at that address.
USER CODE PROGRAMMING
USER CODES - (P1E to P50E) & INSTALLER CODE - (P249E)
There are 51 codes available in the Elite, 50 user codes and 1 installer code. The user codes are located at
addresses 1-50. By default, Code 1 is the Master Code because it has full access to enter program mode. Other
user codes can be programmed as master codes also if required. The Installer code is stored at address 249 and is
used to move from Client Program mode up to Installer Program mode.
Codes 1-50 may be varied in length from 1 to 6 digits. Code 249 must be 3-6 digits.
To program a User Code you must first be in client or installer program mode, then select the address from 1-
50. (If there is already a code programmed at this address, it will be flashed back to you)
NOTE: Not all User Codes may have the ability to access Client Program Mode. The installer can restrict access to
Users so that they have no access to Client Mode or they can have access to change only their code or they may
have access to change all User codes as defined at addresses P101-P150.
To change User code 1 from the default setting of 1,2,3 to 9,8,7,6 you would enter the following data at the keypad.
P 1 E
(Old code is flashed back at the keypad, in this case it will be 1,2,3)
Then 9876 E
3 beeps - program light On or Flashing
The new code will now be displayed back using the keypad LED’s
To program a new user code for User 5 you would enter the following;
P 5 E
(If a code was there it would be displayed if not the display will be blank )
Then 567 E
3 beeps - program light On or Flashing
The new code will now be displayed back using the keypad LED’s
To replace a code simply enter the new code in the same address as the old code. This will overwrite the previous
code but maintain the user permissions as mapped to that user number.

Page 18
To clear or delete a code simply press the BYPASS button at the address where the old code is stored.
e.g. P 3 E <BYPASS> E
3 beeps - Program light On or Flashing
When flashing back codes and values Zone indicators 1-8 are used to indicate digits 1-8. The digit 0 is indicated by
the "A" LED and 9 is indicated by the "B" LED
USER CODE OPTIONS
STANDARD USER CODE OPTIONS - P51E-P100E
Option 1 - Code is assigned to Area A
Option 2 - Code is assigned to Area B
Option 3 - Code is assigned to Area C
Option 4 - Code can Arm Area
Option 5 - Code can Disarm Area
Option 6 - Code can turn on Stay Mode
Option 7 - Code can turn off Stay Mode
Option 8 - Code can Operate Control Functions.
NOTE: Options 1, 2 & 3 set the Area/s the code is assigned to whereby options 4, 5, 6, 7 & 8 determine the
functions the code can operate for the Area/s it has been assigned.
EXTENDED USER CODE OPTIONS - P101E-P150E
Option 1 - Code can override DOTL timer
Option 2 - Code can change dialler telephone numbers
Option 3 - Code can alter the real time clock
Option 4 - User can start a print-out of the event buffer
Option 5 - User can answer an incoming call and start up/down load
Option 6 - User can enter Client Program and change their code only
Option 7 - User can enter Client Program and change all codes
Option 8 - User can allow access to Installer Program mode from Client Mode
Option 1 - Code can override DOTL timer-The user can inhibit the door open too long function of the
access control feature (Control) while in Client Mode. Refer to user manual for details.
Option 2 - Code can change dialler telephone numbers -The User can change telephone numbers
from Client Mode.
Option 3 - Code can alter the real time clock -The User can adjust the Day ,Date & Time of the
Panel Clock from Client Mode.
Option 4 - User can start a print-out of the event buffer -The User can cause a printout of the 255
event buffer to a serial printer from Client Mode.
Option 5 - User can answer an incoming call and start up/down load -The User can cause the
panel to answer an in-coming call for upload/download from Client Mode. See P835E on Page 53.
Option 6 - User can enter Client Program and change their code only -The User can change
their own code only from Client Mode.
Option 7 - User can enter Client Program and change all codes -The User can change any of the
24 User codes from Client Mode.
Option 8 - User can allow access to Installer Program mode from Client Mode – Access to
Installer Mode can be granted by this user from Client Mode.
NOTE: If a user has option 7 or 8 assigned to their code then they can also initiate Walk-test Mode
(P836E) from Client Program Mode.
USER CODE TIME ZONES - P151E-P200E
Users codes may have Time Zones assigned to control their operation. These Time Zones determine when a

Page 19
particular user code will work. Addresses P151E - P200E are used to map the user code to the required Time
Zones. The actual Time Zone parameters are defined at addresses P791E - P814E.
More than one time zone can be assigned to a code. The time zones are numbered 1-8 and are selected by the
numeric buttons 1-8 on the keypad. A value of zero (0) entered at any of these addresses is fixed as 24 hour seven
day access and is the default time zone for all 50 user codes.
P151E TZ E Where TZ represents any Time Zone from 1-8 valid for User Code #1
P200E TZ E Where TZ represents any Time Zone from 1-8 valid for User Code #50
NOTE: The ability to assign more than one Time Zone to each user allows for different time based controls
for different days of the week.
INSTALLER CODE - P249E
This code is used to enter full Installer Program mode (Program light flashing) from Client Program mode (Program
light steady) The default installer code is 000000. To change this code you Must first be in Installer Program Mode
then enter your new installer code at address P249E. The new code will be flashed back to you automatically. The
Installer Code may vary from 3-6 digits in length.
If the alarm is Disarmed then the Installer Code can gain access directly to Installer Program Mode provided Option 6
at address P310E is on.
DURESS DIGIT - P350E
P350E 0-9 Duress Digit (Default 0) - A Duress Alarm is activated only when the "Duress Digit" defined at
this address is prefixed to a valid user code. The resulting Duress Alarm will disarm the Area in
the normal way, operate an output if one is defined and report a duress event via the dialler if
programmed to do so. Values of 0-9 may be entered at this address where 0 = option disabled
and 1-9 represent a valid Duress digit from 1-9.
OUTPUT PROGRAM OPTIONS
PRIMARY OUTPUT OPTIONS - P201E-P208E
This block of addresses (P201E - P208E) is used to map output modifiers to each of the 8 outputs available on the
Elite. The optional 4 way relay output board (OUTPUTX4) can be configured to follow the program options for any of
the 8 outputs, the 4 relays can be assigned as output 1 or 5, 2 or 6, 3 or 7 & 4 or 8.
P201E 1E = Invert output #1 - Default off
2E = Flash output #1 - Default off
3E = Single pulse to output #1 - Default off
4E = Lockout output #1 once reset - Default off
5E = Output mapped to Remote Command Control - Default off
6E = Output mapped to local Command Control - Default off
7E = Day zones linked to pulse timer - Default off
8E = Output pulses on a 24 hour zone alarm - Default off
Option 1 Invert Output - This option is used to invert the normal state of the output. The Elite uses open
collector type transistor switches and the default state of all outputs is off or high. When in alarm the
transistor switch is turned on and the output is switched low. The invert option reverses this function.
Option 2 Flash Output - This option causes the output to switch on and off at a rate set by the pulse timer for the
output when in alarm and is normally used to flash a lamp during an activation.
Option 3 Single Pulse to Output - This option, when applied, produces a single pulse set by the pulse timer at
the output during an alarm.
Option 4 Lockout Once Reset - This option is used to limit the output to one operation per arming period.
Option 5 Output mapped to Remote Command Control - This option is used to map an output to the remote
command control function whereby the output can be controlled via the telephone (this requires the
optional VOICE or DTMF board to be fitted)

Page 20
Option 6 Output mapped to Local Command Control - This option is used to map an output to the local
command control feature whereby the output can be controlled directly from the keypad. The DTMF
command control code at address P371 is used for this local control function.
Option 7 Day Zones Linked to Pulse Timer - Day Zones programmed to operate this output will pulse the output
at the rate programmed for the pulse timer (e.g. if it is output #1 then the timer at P571E applies).
Option 8 Pulsed 24 hour alarm - If a 24 hour zone activates the alarm this option will cause the output to pulse at
a rate equal to the value set for the pulse timer for this output. This feature is provided to differentiate
between a burglar and fire alarm using the same siren.
P202E - P208E As per P201E above for Outputs 2-8
SPECIAL ALARMS TO OUTPUT OPTIONS - P211E - P218E
In this block of addresses P211E relates to output #1, P212E relates to output #2 etc
P211E 1E = Keypad Panic Alarm to Output #1
2E = Keypad Fire Alarm to Output #1
3E = Keypad Medical Alarm to Output #1
4E = Duress Alarm to Output #1
5E = Wrong Code Tamper Alarm to Output #1
6E = Radio Key Panic Alarm to Output #1
7E = 24 Hour Zone Alarm to Output #1
8E = 24 Hour Fire Zone Alarm to Output #1
Option 1 Keypad Panic to Output - This option is used to map the operation of the keypad panic button to an
output i.e. when the Panic button (or 1 & 3) on a keypad is pressed any output with this option enabled
will turn on.
Option 2 Keypad Fire Alarm to Output - This option is used to map the operation of the keypad Fire Alarm
(buttons 4 & 6) to an output i.e. when the Fire Alarm (4 & 6) on a keypad is pressed any output with this
option enabled will turn on.
Option 3 Keypad Medical Alarm to Output - This option is used to map the operation of the keypad Medical
Alarm (buttons 7 & 9) to an output i.e. when the Medical Alarm (7 & 9) on a keypad is pressed any
output with this option enabled will turn on.
Option 4 Duress Alarm to Output - This option is used to map a Duress Alarm to an output. A Duress Alarm is
generated when the alarm is unset by a valid user that adds the duress digit to the beginning of their
code.
Option 5 Wrong Code Tamper Alarm to Output - This option is used to map the Wrong Code Tamper Alarm to
an output. A Wrong Code Tamper Alarm is generated if an invalid code is entered more than 4 times at
a keypad. This option will cause the output to turn on when this alarm condition is present.
Option 6 Radio Key Panic Alarm to Output - This option is used to map the operation of the Radio Key Panic
Alarm to an output i.e. when the Radio Panic is generated any output with this option enabled will turn
on.
Option 7 24 Hour Zone Alarm to Output - This option is used to map 24 Hour Zone Alarms to an output i.e.
when the 24 Hour Zone Alarm is generated any output with this option enabled will turn on.
Option 8 24 Hour Fire Zone Alarm to Output - This option is used to map 24 Hour Fire Alarm to an output.
When the 24 Hour Fire Alarm is generated this will cause the output to flash at a rate set by the pulse
timer for this output to identify the difference between a fire alarm and normal burglar alarm.
SECONDARY SPECIAL ALARMS TO OUTPUT OPTIONS - P221E - P228E
In this block of addresses P221E relates to output #1, P222E relates to output #2 etc
P221E 1E = Zone Tamper Alarm to Output #1
2E = System Tamper Alarm to Output #1
3E = Mains Failure to Output #1
4E = Panel Battery Low to Output #1