CYCMOTOR PHOTON User manual

photon
user manual

1
SAFETY & PRECAUTION
•General Safety
•Before the Ride
•Installation & Use
•Disclaimer
01
SPECIFICATION
•Description
•Specications
•Parts List
•Dimensions
•Motor Body Dimensions
02

Kindly read through the entire user manual. This manual contains
important information to reduce user risk as well as instructions for this
product’s proper use. Do not discard the manual but keep it for reference.
Note that the user’s personal safety remains the user’s responsibility and
that the user must contact CYCMotor Ltd or their ocial product dealer
directly for any further guidelines or assistance.
Never interfere with the movable parts when the drive unit is connected
to a power supply. This could result in serious injury if the system is
accidently engaged.
This product is a powerful motor system that is dangerous for children
and must be handled by an adult at all times. Small components and
accessories may also present a choking hazard. Keep the motor system
and accessories out of reach from children.
All components and accessories may only be replaced with identical
components directly supplied by CYCMotor Ltd or an ocial product
dealer. CYCMotor Ltd cannot be held liable for any damages as a result of
using unapproved parts.
This product only complies with local, state, and federal regulations if
speed limits are set accordingly. Ensure that you have set up your X1
Stealth kit according to your loca, state, and federal regulations when
using and registering this drive unit on a public road/area.
Ensure that the drive unit chain has the proper tension. Incorrect tension
could cause jamming of the system and result in injury while riding.
Inspect the chain tension regularly.
Ensure that the chains are properly lubricated. Cleaning and lubricating
your chain with regular bicycle chain cleaner, is advised regularly.
When connecting a power supply, make sure that the power supply is
completely connected. Faulty connection could result in a short circuit
and damage the controller or batteries.
Inspect all electrical wires and plugs for damage regularly.
Secure all wires properly. Ensure that no loose wires are dangling from the
bike that could be jammed into any movinf parts.
Before turning on the system, ensure that the throttle can be twisted
freely without friction and that the throttle can return to its original
position withour restriction. This is to prevent any uncontrolled response
of the system.
2

Do not install anything other than the parts and accessories that came
with this drive unit. Doing so could damage the product.
The drive system can be activated and deactivated by holding down the
on/o button the display.
Avoid changing the bke gear (note: this is dierent from the drive unit’s
assist level) while the drive unit is powering the bike. This may lead to
excessive wear on the chain and chain rings or other gear related failture.
When changing gear, use human input only. After the gear is changed,
you may accelerate again with the throttle or continue using the PAS.
Take o with the appropriate assist level & bike gear.
This product is splash proof and rain proof but NOT WATER PROOF. Do not
submerge it underwater.
If you require any more information or have any questions about the user
manual disclaimer, please feel free to contact us via email at
[e-mail] or call [phone].
All the information contained in this user’s manual is published in good
faith and for general informational purposes only. CYC Motor Ltd does
not make any warranties about the completeness of this information and
encourages further inquries as stated above if needed. CYC Motor Ltd will
not be held liable for any losses and/or damages in connection with the
use of this product. The use of this product is at the user’s own risk.
Notice: Please contact CYC Motor Ltd if you are unsure about the
assembly instructions or for any further assistance as CYC Motor Ltd will
be held liable for any losses and/ or damages created by the assembly.
3

36 - 52V
>300 RPM
>90%
1500W (CYC X6)
150 N.m. (CYC X6)
Anodized Black
2.7kg
4.5kg
7075-T6
165mm or 175mm
190mm
FOC
Hall & Temp. Sensor
11/53 option with 32T
11/63 option with 38T
68mm, BB92, BB30/PF30
(compatible with adapter)
4

SW102 or DS103 Display Magnetic Bluetooth
Speed Sensor
Thumb, Half-Twist or Full Throttle
PHOTON assembly
Headlights
(optional)
Controller Extension Wires
(optional)
Magnetic Brake Sensors
(optional)
Bottom Bracket Spacers
(3, 5 & 7mm for BSA version;
2mm (2pcs) for BB92 version)
5

FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection againstharmful interference in a residential installation. This equipment generates,
uses and can radiateradio frequency energy and, if not installed and used in accordance with
the instructions, maycause harmful interference to radio communications. However, there
is no guarantee thatinterference will not occur in a particular installation. If this
equipment does cause harmfulinterference to radio or television reception, which can be
determined by turning the equipmentoff and on, the user is encouraged to try to correct the
interference by one or more of thefollowing measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer
could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.