Dancover GH140055 User manual

21-04-2021
for
Arched Cover f/Raised Garden Bed
0,75x1,5x0,45m
Manual

1
NOTE: The lower bed is supplied separately, in the photo only an application example.
NOTE: Use protective gloves to assemble the structure!
COVER FOR RAISED GARDEN BED
No.
Pcs
1. 4
2. 2
3. Arches 1230 mm 3
4. 2
5. 4
6. Rear and side reinforcements (folded ends) 4
7. Hinges 50x40 mm 2
8. 4
9. 64
10. 25
11. 93
12. 27
13. 3 m
14. 2
15. 1
16. 1
Corners for connecting the rear and side parts with 4 holes 40x40 mm
Parts list
Side parts 783 mm
Front part 730 mm
Reinforcements between the arches 688 mm
Corners for polycarbonate mounting 40x30 mm
M5x16 mm screws
M5x40 mm screws
M5 nuts
Gaskets plastic, transparent
Tape for sealing sheet ends
PC cover ends
Cover for covering 1400x1610 mm
Handle

2
Installation instruction
1.
2.
3.
4.
5.
6.
2
2
1
1
1
2
1
5
9
2
2
2
1
2
5
9
1
1
6
2
2
1
3
1
3
2
3
1
3
4
4
4
3
Arrange the parts as shown in the figure. 783 mm long parts on the sides (1) and 730 mm long parts on the
ends (2).
Join the corner parts of the structure (1; 2) with the corners for connecting the rear and side
parts (5). Use M5x16 mm bolts (9) with nuts (11). Do the same for all 4 corners.
At the joints of the side parts (1), turn only 2 lower M5x16 mm (9) lower bolts
with nuts (11). Leave the upper holes free. Do the same on both sides.
Fasten the rear and side parts using reinforcements (bent ends) (6) and M5x16 mm
screws (9) and M5 nuts (11). Do the same for all 4 corners.
Fasten the arches to the already assembled structure
using M5x16 mm screws (9) and M5 nuts (11). A total
of 3 arches (3) are fastened: 1 at the ends and 1 in the
middle.
Fasten the fastenings between the arches (4) with screws M5x16 mm (9) and nuts (11) (2 pcs.).

3
7.
8.
9.
10.
11.
8
3
1
3
1
7
3
4
7
9
7
3
14
12
14
12
Fasten the polycarbonate sheets (14) with M5x40 mm screws (10)
with transparent spacers (11) and nuts (11) at the bottom and
M5x16 mm screws (9) with transparent spacers (12) and nuts (11)
through the corners. Do the same on both sides. Important: Peel off
the protective polycarbonate films before placing the sheet on the
structure. Do not mix polycarbonate sides. The UV-resistant side
must face outwards. This is indicated by the marked film.
Place the assembled bed cover on an existing metal bed. Make sure the
cover is in place. Mark the holes for drilling holes in the bed. Using a 6 mm
metal drill (drill not included), drill 4 holes to attach the cover to the structure.
Screw the cover to the structure with M5x16 mm screws (9) with nuts (11)
through the hinges.
Tighten the structure using a screwdriver and 8 mm head.
Fasten the hinges to one of the side parts (1) with M5x16 mm bolts (9) and nuts (11).
Fasten the corners (8) for fixing the polycarbonate to the rear arches with M5x16
mm screws (9) and M5 nuts (11).

4
12.
13.
14.
15.
15
12
15
12
16
16
Fasten the handle (16) using M5x40 mm bolts (10) and M5 nuts (11).
Seal the edges of the polycarbonate with the added aluminum strip (13).
Cover the structure with a transparent tarpaulin (15). Level so that the entire
structure is evenly covered. The awning is attached to the structure with M5x40
mm screws (10) with M5 gaskets (11) and nuts (12). The edges of the sheet must
engage on the sides behind the polycarbonate sheets.
Use a sharp knife to trim the protruding polycarbonate sheets (14) to the structure.

I
For more information
please visit:
www.dancovershop.com
l
l
l
l
l
l
l
l
l
l
l
Dancover A/S
Lyngevej 16A, Nørre Herlev
3400 Hillerød
Denmark
Head office: