Dancover Orangery GH170010 User manual

07-05-2021
for
Orangery
4,45x4,45x2,52m
Manual

Assembly Instructions
—— For Sliding Door
Walk-in Greenhouse
Orangery

2
Statement
Dear Customer!
May we congratulate you on buying new Greenhouse.
We feel sure that by following the detailed assembly instructions, you will find as much
pleasure in actually building the greenhouse as the many hours you will spend on your
greenhouse in the future. The assembly instructions are a combination of text and illustra-
tions and no technical knowledge is required for the erection of the greenhouse. The
frames are numbered and packed separately corresponding to the succession in the as-
sembly instructions
Assemble one section at a time. However, bolts and various fittings for all sections will be
found in pack of instructions.
Each pack is specified in the list of components. All detailed illustrations are marked with a
symbol.
Guarantee
We grant a comprehensive guarantee that covers replacement or repairs of defective parts
due to material or manufacturing fault. The guarantee does not cover transport, assembly,
freight etc. Glass is not covered by the guarantee. The guarantee is invalid if the green-
house is not assembled according to these instructions.
Winter Protection
Our greenhouse is constructed with frame dimensions up to 50% stronger than most of
the competing products. We still recommend you to protect your greenhouse during the
winter.
Supporting the roof ridge at the centre of the greenhouse.
Removing greater snow loads.
Taking precautions against snow falling down from, for instance a roof.
Preventing the wind from damage the greenhouse door and windows.
Foundation
The base is maintenance free and, of course, all fittings are included. Remember to order
concrete pipes and concrete at you local dealer, as these are not included in the delivery.
Maintenance
Complaints
Grease doors, hinges and door track
Clean the gutter for leaves etc
Adjustment of windows
Replacement of broken glass
Clean the greenhouse with disinfectant before and after the growing season
We put severe demands on quality to secure that you get faultless products.
However, should a complaint occur, we kindly ask you to contact the dealer, from whom
you have bought the greenhouse, To secure a quick service you should specify the extent
of the defect by means of the list components in the assembly instructions.

3
Tips
The base has to be fastened in a non-freezing depth <80cm>.
The greenhouse is to be fastened to the base.
The base has to be 100% level and square. The easiest way to ensure this is
that the two diagonal measurements are identical.
We recommend greasing the screws for the doors for an easier assembly.
Glazing should only be carried out in fairly calm weather.
Make sure that the greenhouse is square before starting to glaze.
We recommend the frames to be degreased with acetone before glazing.
We recommend using working gloves while glazing.
An assistant make the job easier.
Tools
The greenhouse is assembled by means of the following tools:
Spirit level
Spanner/socket spanner 8 and 10 mm
Screw driver
Silicone pistol
Acetone for degreasing the frames
Please put on gloves avoid of slitting your hands.
Avoid of crashing the material, results in un-
shapes, it is not fits in fixture.
Avoid of materials cuts the polycarbonates
sheets.
Cautions

4
Base
Base Base Base Base Anchor
legs Corner- ite Fixing tabs M6x10 M6 M6x10 Crop Washer
GTA10 1x4392 3x2958 2x747 2x1464 9619 58 77 19 13
1
2
3
123

5
Base
# m5
GTA10 24
IMPORTANT Before assembling aluminium base, the end trough centers of seven legs
should match both end trough centers of side sills and front & rear sills at the same time.
side sills
front & rear sills
Please match seven cor-
ner troughs together at
the same time

6
# 7001 7002 7003 7206 7268 7009 7211 7212 7015 7020 7021
Size 1600 2043 2043 446 2896 733 1656 1656 1712 1456 2856
QTY 21111411211
# a1 a2 a3 G-m1 G-m2 a20G-p1
Size M6x10 M6 M6x15 ----
QTY 30 34 412341
1
7268
Front Gable
2
345
5
6
7
8
9
7001 70017002 7003
7206
7009 7009
7009
7211 7212
7015 7015
7020
7021

7
Front Gable
2
7268
7002
7015
a3
34
5
6
7001
7009
a1 7009
7015
a1
a17009
7002
7001
7211
a1
7009
G-m2
7015
1
7001
7268
a3
89
7206
7020 a1/a2
7211 7212
G-m1
7206
77211
7002
7020
a1/a2
7020
7021
Section View
7020
7021
a1/a2

8
Rear Gable
# 7001 7002 7003 7207 7024 7210 7213 7214 7015
Size 1600 2043 2043 2436 2896 2884 1656 1656 1712
QTY 211112112
# a1 a2 a3 G-m1 G-m2 a20G-p1
Size M6x10 M6 M6x15 ----
QTY 25 30 512301
1
7024
2
456
6
7
8
9
7001 70017002 70037207
7210
7210
7213 7214
7015 7015
3

9
Rear Gable
4
5
7001
7210
a1
7210
7015
a1
7
7001
7213
a1
7210
G-m2
7015
87213
7002
a1/a2
9
a1/a2
7207
7213 7214
G-m1
12
3
6
7210
7002
a1
7001
7024
a3
7024
7002
7015
a3
7207
7024
a3

10
a3
7034
7026
7036 7036 7036 7036 7036
7029 7029
1
2
34
7036
7036
7029
7036
7029
a3
Note: Please add extra bolt into channel for eave
cantilever use in advance.
Side wall
# a1 a2 a3 a20
Size M6x10 M6 M6x15 -
QTY 38 55 17 55
# 7026 7029 7034 7036 7401 7402 7403 7404 7405 7406 7407 7408 7409
Size 4330 1732 4353 1600 1600 1433 716 1433 716 1458 741 1458 741
QTY 1617211111111
7026
7034
7026
13
42
7034

11
5
6
a3/a2
7401
7404
7405
7408
7409
Side wall 5
6
7
8
9
10
11
12

12
Side wall
789
10 11 12
7409
7409 7408
7401
7408
7405 7405 7404
7401
7404
a3/a2
a3/a2 a3/a2
7036
7029
7029
13
15
17
14
16
13
14
15 16 17
7409
7029
7029
7405 7404
7408
7036
7404
7036 7029
a3/a2
7408
7029
Note: Bolts
need to be
slid into cor-
ner bars for
eave canti-
lever brac-
ing use
later.
Note: Bolts need to be slid into glazing
bars for eave cantilever bracing use later.

13
Roof
# 7037 7251 a1 a2 a20 m3
Size 468 616 M6x10 M6 --
QTY 11 7117 117 117 8
# 7412 7413 7420 7421 7422 7423 7244 7045 7046 7049 7252 74277415
Size 4353 2882 1602 1602 774 774 1656 1449 2166 4317 1781 17692222
QTY 1122227221422
VERY IMPORTANT:
1. Before attaching roof bars to structure, bolts will need to be slid into each roof bar for the ridge cantilever,
two more for hanging basket rail, one more for the eave cantilever bracing between the roof and the side,
one more for the vent slam bar attaching (If vent position to be decided).
2. Prior to tightening the roof bars to structure. Please ensure that the roof bar is pushed up hard against
the ridge and the gutter bar.
3. In order to avoid the result in a slight outside bow of the gutters and a slight downward dip to the ridge.
Please support the ridge at the center of greenhouse firstly, and then tightening the nuts of ridge cantile-
ver and eave cantilever bracing bars.
7412
7413
7415
1
2
3
321
7412
74137415
7415
7409 7408

14
Roof
4
5
6
7
89
10
11
7412
7413
7422 7420 7423
7421
7422
7420
7423
7421
7244 7244
72447244724472447244
7049
7045
7046 7046
7045
7252 7252
7252 7252
7427 7427
7415 7415

15
Roof
45
67
89
7244
7036
7252 7427
7252
7244
7036
7244
7244 7420
7412
7034
7412
7034
7049 7049
10 11
7415
7422 7423
7045 7046
m3
7415
7420 7421
7427
m3

16
Roof
12
13
7251
7037
7244 7244
7244
7036
14
12
14
13
7037 7037
74157420 7421

17
Vent
4
7054
7056
7056
47054 7056
a2
a1
# 7053 7054 7055 7056 7057 7067 a1 a2 a4 a7 a10 p3 a20
Size 739 718 701 593 300 -M6x10 M6 Φ3.9x8 M4x8 M4 --
QTY 1112128826628
11
11
1
7053
7244 7244
23
2
3
7244
7053
7053
7067
a7
a10

18
Vent
7055
7055
7057
5
6
5
6
7
7055
7057
a7
a10
7055
7056
8
p3/a4
9

19
Door
# 7058 7059 7060 7061 7062 7063 7065 a1 a2 a5 G-p5
FLUFF
7064 m10a15 a16 a20
Size 1938 1938 1938 715 715 715 - M6x10 M6
Φ3.5x19
-1938350 - M6x12 Φ6 -
QTY 211222212 13 28 22241112
7059 7058
7063
7061
7062
1
2
3
123
7058
7063
7061
7058
7058
7062
7061
7062
7058 705870597060
7063 7063