Dancover GH152100 User manual

for
Greenhouse Lean-to
1,27x3,04x2,12m
Manual
29-11-2019

Assembly Instructions
PRODUCT SIZE(LxWxH):304X127X212CM
PLEASE READ CAREFULLY BEFORE ASSEMBLY

CONTENTS

KEEP WORKING AREA CLEAN AND DRY
A cluttered, damp or wet working area may cause injuries.
Safety Warning & Advice
PREPARE A FLAT AND LEVEL BASE
Make sure your greenhouse is located on a flat and level surface.
Although this greenhouse is designed to withstand greater wind loads than many other
greenhouses, do not install it in on a windy day or in an area which is subject to high winds.
A partially completed greenhouse may be seriously damaged if it is left in this state. It is
your responsibility to safely and securely anchor the greenhouse, having regard to wind
conditions in your area.
DO NOT INSTALL THE GREENHOUSE ON A WINDY DAY OR
IN AN AREA SUBJECT TO HIGH WINDS
POLYCARBONATE SHEET
Remove approximately 2 inches of film from all sheet edges before installing and remove all film
immediately after the construction is completed. Please ensure that the side with the white film
faces outwards.
CHECK PARTS BEFORE ASSEMBLY
All parts have been well labelled. Please sort, separate and identify all components before
construction and check against the parts list in this manual.
WARNING
Do not install this product when you are tired or distracted from the job at hand. We recommend
that you use gloves during assembly.
POWERED SCREWDRIVER RECOMMENDED
This quality greenhouse features self-tapping screws to provide strong joints. As the name
suggests, the screws tap their own thread. Driving in self-tapping screws requires more force
than conventional screws. A powered screwdriver is therefore recommended.

B1
A1
C
C
C
1
C
B1
A1
16*S01
4*S01
C
A1
B1
PART NO QTY
4C
2
A1
2
B1
1
M6X10
S01 16
16
M6
M01
M4.2X16
Z01 28
Base Assembly
Fixing the greenhouse to
the base is recommended.
It is best to do this at
the end, after the
greenhouse has been fully
assembled.

L13
L10
22
L13
2
L13
L13
A1
L10
L10
L10
A1
222
A1
A1 Z01
Z01
2
L08A
C
C
C
22
L08A
2
L08A
L08A
B1 B1 Z01
Use a powered screwdriver to fix the self-tapping screws (Z01) through the cills (L08A, L10 and L13)
and base plinth (A1 and B1). The screws should be evenly spaced to ensure a neat appearance. The
recommended spacing of the screws is 238mm. You can mark the painted surfaces with a pencil.

1
PART NO QTY
PART NO QTY
PART NO QTY
1
L01A
1
L10
1
L04A
1
L05B
1
L11
1
L03B
3
Y2
1
Y1
Y4
Y5
1
1
1
L01B
2
W01
1
L01A
1
L13
1
L04B
1
L05A
3
L03B
1
L01B
PART NO QTY
2
L08A
PART NO QTY
1
L07
4
L02A
L12A 2
1
L06
1
L02D
1
L03B
4
1
Y7
Y9
5
Y6
1
L09
1
1
2
J01R
J02L
J02R
J03
1
L14
3
PART NO QTY
1
W06
1
W08
M6X10
S01 35+2
M6
M01 35+2
M4X10
S02 2
M4.2X16
Z01
M4X10
M02 2
103+5
PART NO QTY PART NO QTY
PC/Glass
2
L19
1
L21
1
L20
1
L15
1
L17
2
L16
2
L18
1
Y10
1
Y11
2
Y12
1
L01C
1
Y8
Y13 1
1
L01D
2
W05
J01L 1
1
L02C
2
L02B

L21
L19
L20
L19
4*Z01
Y10
PART NO QTY
4
M4.2X16
Z01
1
4
Z01
Z01
2
L19
1
L21
1L20
1
W06
Y10
M4X10
S02 2
M4
M02 22*S02
W06
L21
Vent Assembly
Slide 2 bolts (S02) into the bolt channel (L21)
and fix the handle (W06) in the middle

L18
L18
L16
L16
L17
L15
16*Z01
PART NO QTY
16
M4.2X16
Z01
Y12
Y11
Y12
5
Z01
Z01
Z01
Z01
Z01
Z01
Z01
Z01
Z01
Z01
1
L15
1
L17
2
L16
2
L18
1
Y11
2
Y12
Door Assembly

6
L10
PART NO QTY
1
L01A
1
L10 3
M4.2X16
Z01
1
L04A
2
1
1
L10
L10
2
L01C
3
3
L01A
L01C L04A L01A
L10
1
L01C
L04A
L01C L04A L01A
1059MM
1. Lay out the glazing bars (L01A,L01C, and L04A) and
the cill (L10). Ensure that the cill upstand is on the inside
and that L01A&L01C is the correct way round.
2. Make a pencil mark on the glazing bars (L01A, L01C)
at a height of 1059mm from the bottom. This will help
later when fitting part L05B.
3. Fix the glazing bars (L01A,L01C, and L04A) to the cill
(L10) with the self-tapping screws (Z01) using a powered
screwdriver. The inside of the glazing bars feature guide
lines which indicate the correct screw positions (see detail
drawings below). Be careful to ensure that the screws are
in the correct position (see detail drawings below).
Screw
position
Screw
position Screw
position
Screw
position
Screw
position