Dancover PH08-SSA User manual

Pyramid Heater
Manual
08-04-2014

1
ASSEMBLY AND OPERATION INSTRUCTIONS
WARNING
Read this instruction before using this appliance. The
appliance must be installed in accordance with the
instructions and local regulations. The use of this
appliance in enclosed areas can be dangerous and is
PROHIBITED.
•Do the leak test after each changing LPG cylinder.
•Never check for leaks with a match or open flame
•Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this appliance.
IF YOU SMELL GAS
•Close the valve of the gas cylinder or regulator.
•Extinguish all naked flames; do not operate any
electrical appliances
•Check for leaks as detailed in this instructions
•If odor persists, contact your dealer or gas supplier
immediately
DO NOT USE THE HEATER WHEN IT IS RAININGAND DO NOT LETANY LIQUID
COME INTO CONTACT WITH THE GLASS TUBE WHEN THE HEATER IS IN USE.
FOR OUTDOOR USE ONLY.
KEEPTHE INSTRUCTIONS FOR FUTURE REFERENCE
PH08-SSA Pyramid Heater

PRECAUTIONS
THIS APPLIANCE OUTDOOR USE ONLY
· Check the hose before each use.
· Disconnect the gas cylinder before moving the heater.
· Do not attempt to alter any parts.
· The appliance should not be used in basements or below ground level.
· It must always be placed on a solid and level surface.
· Only use a regulator that is suitable as provided.
· Do not clean the heater with cleaners that are combustible or corrosive.
· Do not paint protection guard, control box or reflector.
· The LPG gas cylinder valve should be turned off when the heater is not in use.
· Don't not use the heater when it is raining, and do not let any liquid splash to the glass tube when
the heater is working.
· Keep the children away from the heater.
· Do not move the appliance when in operation.
· After a long break of operation, the gas parts in the control box of the heater and the hose should
be inspected for spiders, spider webs or other insects.
· Check the heater immediately if any of the following exists:
1. There is smell of gas.
2. The burner makes popping noise during use (a slight popping noise is normal when the
burner is extinguished after use).
· If you smell gas, turn off the valve immediately. If smell persists, contact the dealer or gas
supplier immediately.
· Children and adults should be aware of the high surface temperature hazard, and should keep a
safe distance away.
· Keep the ventilation opening of the cylinder enclosure free and clear of debris.
· Do not obstruct the ventilation holes of the cylinder housing.
· The tubing or the flexible hose must be changed within the prescribed intervals.
· Use only propane gas
· In case of strong wind, particular attention must be taken against the heater tilting to one side..
APPLIANCE LOCATION
-Always maintain proper clearance from combustible
materials, i.e. top 800mm and sides 650mm minimum.
-THIS APPLIANCE OUTDOOR USE ONLY
2

LEAK TEST
Gas connections on the appliance are leak tested at the factory prior to shipment. Possible
mishandling of the appliance during the shipment might contribute to product integrity as a whole.
A complete gas leakage test must be performed again at the installation site. Please follow the
procedure below for leakage test.
-Make a soap solution of one part liquid detergent and one part water. The soap solution can be
applied with spray bottle, brush or rag. Soap bubbles will appear where a leak is present.
-Make sure the control tap is in the OFF position (full disk = ●) on the control panel.
-Turn on the gas supply and check for bubbles from the hoses and connections. Presents of
bubble means that a leak path is present.
-If a leak is present, turn OFF the gas supply immediately, tighten any leaking fitting carefully,
turn gas again and recheck.
-Never leak test while smoking.
3

PARTS LIST-1
Part NO.
Part Name
QTY
Picture
Remarks
Middle Plate 1
2
Control Box
1
Preassembled in
the Middle plate
3
Bottom Plate
1
4
Lower
Support
4
5
Upper support
4
6
Upper Plate
1
7
Plate cover
1
Preassembled in
the Middle plate
8
Glass tube
1
One more spare
glass tube is
provided
9
Damper
1
Preassembled in
upper plate
10
Reflector
1
1
4

INJECTOR
Part NO.
Part Name
QTY
Picture
Remarks
11
Lower protection
guard
4
12
Fixing
bracket
4
13
Side panel
3
14
Front panel
1
A chain is
preassembled in this
panel
15
Screw M3/16”
66
All preassembled in
relative parts
16
Knob
1
17
Chain
1
Preassembled in the
front panel
18
AA battery
1
Optional part
5
PARTS LIST-2

HEATER ASSEMBLY
Tools Required:
1 Phillips head screwdriver, 1 adjustable spanner
1. Take the control box(2) and the plate
cover(7) out off the middle plate(1) by
unscrewing the screws(15)
2. Connect and fix the 4 lower
supports(4) to bottom plate(3) and
middle plate(1) with the screws(15)
3. Connect the 4 upper supports (5) to the
lower supports (4) and fix with 4
screws(15), then fix the upper plate(6)
to 4 upper supports(5) with screws(15).
4. Fix the plate cover(7) onto the
middle plate(1) with screws(15).
6

5. Install a AA battery(18) into the
control box, then, fix the control
box(2) underneath the middle plate(1)
with screws (15)
6. Carefully put the glass tube(8) up
through the centre hole in the upper
plate(6), Make sure the rubber ring is
attached on the lower end of the glass
tube(8). Move and sit the glass tube(8)
through the hole of the plate cover(7)
on the middle plate(1), check and
ensure that the glass tube(8) cover the
centre hole of the middle plate(1)
7. Fix the reflector (10) onto the damper
(9).
8. Attach the protection guards (11) onto
the frame by placing its hooks into the
holes of the frame. Fix the guards with
the fixing brackets(12)
7

9. Fix 3 side panels (13) with the screws (15).
Note: Do not cover the side where the control knob is.
10. Screw the knob (16) onto the front panel(14), attached the
connector back the front panel, screw them together with
2pcs M4X8 bolts, hook the chain(17) to the hole in control
box, then close the panel to the middle plate ,the panel is
attracted by the magnets.
Tips: the chain can hold the panel while operating the control
Completed
8

OPERATION
Preparation:
You will need to purchase a LPG cylinder.You need a suitable
size LPG cylinder that can be installed to the compartment.
You have to use pressure regulator with an outlet pressure to
comply with the appliance category.
Connect the hose to the hose connector in the control box
Warning:
Never use the heater while it is raining, the glass tube will break.
The glass tube will be extremely hot when it is working, never try to touch it and keep
children away from the heater.
Always ensure the heater is seated firmly, the glass tube may break if the heater falls.
Never use the heater if the glass tube has any crack or damage.
LIGHTING INSTRUCTIONS
1.Ensure that the control knob is OFF. Slowly open the gas
cylinder valve.
2.Press and turn the control knob to LIGHT position, push the
igniter to generate spark while keeping control knob pressed in.
3.Check for the pilot flame through glass tube. If pilot does not
light, turn control knob to ‘OFF’ position, wait two minutes
minimum and try again. Several attempts may be necessary.
4.If the pilots alight, keep the control knob pressed for 15 seconds
then turn the control knob to ‘LOW’.
5.For maximum heat turn control knob to ‘HIGH’.
6.To turn heater off, turn control knob to ‘OFF’.
7.Close the valve of the gas cylinder or the regulator after use.
OFF
LIGHT
LOW
HIGH
9
●
●
●
●
OFF
LO
HI

CLEANING/MAINTENANCE/STORAGE
CLEANINGAND MAINTENANCE:
To enjoy outstanding performance of your heater for years make sure to perform the following
maintenance activities on a regular basis:
●Keep exterior surfaces clean.
-Use warm soapy water for cleaning. Never use flammable, corrosive or abrasive cleaners.
-While washing your unit, be sure to keep the area around the burner and pilot assembly dry at
all times. If the gas control is exposed to water in any way, do NOT try to use it. It must be
replaced.
●After a long break from operation, the unit should be inspected for spiders, spider webs or
other insects.
●Air flow must be unobstructed. Keep controls. Burner and circulating air passageways clean.
Signs of possible blockage include:
-Gas odour with extreme yellow tip to the flame.
-Heater does NOT reach the desired temperature.
-Heater glow is excessively uneven.
-Heater makes popping noises.
●Spider and insects can nest in burner or orifices.
This dangerous condition can damage heater and render it unsafe for use. Clean burner holes by
using a heavy-duty pipe cleaner.
Compressed air may help clear away smaller particles.
●Carbon deposits may create a fire hazard. Clean reflector and glass tube inside with soapy
water if any carbon deposits develop. Always be careful when cleaning the glass tube.
STORAGE:
Between uses:
●Turn the control knob to “ OFF ” position.
●Turn LPG cylinder to“OFF”position.
●Store heater upright in an area sheltered away from weather (such as rain, sleet, hail, snow).
●If possible, cover the heater to protect exterior surfaces and to help prevent dust and debris
collecting in air passages.
During periods of extended inactivity or when transporting:
●Turn the control knob to “ OFF ” position.
●Disconnect LPG Cylinder and move to a secure, well-ventilated location outdoors.
DO NOT store in a location that will exceed 50 degrees C.
WARNING
FOR YOUR SAFETY:
●
DO NOT touch or move heater for at
Least 45 minutes after use.
● Allow all burner elements to cool
before Touching.
NOTE
●In a salt-air environment (such as
near an Ocean) corrosion occurs
more quickly than normal.
●
Frequently check for corroded areas
and Repair them promptly.
●Wait until heater is cool before
covering.
10

Contact information
Head office:
Dancover A/S
Nordre Strandvej 119 G
3150 Hellebæk
Denmark
For more information
please visit:
www.dancovershop.com
National contact
Denmark:
[e-mail]
UK:
[e-mail]
Spain:
[e-mail]
Italy:
[e-mail]
Germany:
[e-mail] Switzerland: [e-mail]
France:
[e-mail] Austria: [e-mail]
Sweden:
[e-mail]
Finland:
[e-mail] Nederland: [e-mail]
Poland:
[e-mail] Ireland: [e-mail]
Luxembourg:
[e-mail] Belgium: [e-mail]
Norway:
[e-mail]