DANLERS WACEPIR Quick start guide

Installation notes
DANLERS Limited, Vincients Road, CHIPPENHAM, Wiltshire, SN14 6NQ, UK.
Telephone: [phone] Fax: [phone]
E-mail: [email protected] Web: www.danlers.co.uk
Company Registered Number 2570169 VAT Registration Number 543 5491 38
Also available from DANLERS
• PIRoccupancyswitches•Daylightlinkeddimmers•Manualhighfrequencydimmers
• Photocells • Radio remote controls • Time lag switches • Outdoor security switches
• Dimmers•Heating,ventilationandair-conditioningcontrols•Bespoke/O.E.M.products
Please call for more information or a free catalogue, or visit our website.
ThisproductconformstoBSEN60669-2-1andBSEN55015.
Pleaseensurethemostrecenteditionoftheappropriatelocalwiringregulationsareobserved
andsuitableprotectionisprovidede.g.a10ampcircuitbreakerandvoltagesurgeprotection.
Pleaseensurethatthisdeviceisdisconnectedfromthesupplyifaninsulationtestismade.
Thisproductiscoveredbyawarrantywhichextendsto5yearsfromthedateofmanufacture.
Precautions and Warranty
Wall or ceiling mounted PIR occupancy switch
WACEPIR
DANLERS3-wirewallorceilingmountedpassiveinfra-redoccupancy
switch (WACEPIR) should be wall mounted at a location where a
neutralconnectionisavailable.
TheWACEPIRincorporatesapassiveinfra-redquadsensortodetect
movementofawarmbodywithinthedetectionzone(diagramBorC)
andaphotocelltomonitortheambientlightlevel.
Upondetectingmovement,iftheambientlightisdarkenough,the
WACEPIR switch willturn theload on.Theambient threshold can
be set by the user to between approximately 30 lux and 1000 lux
and maximum (photocell inactive) at the PIR via the LUX adjuster
(diagram A).
Ifnomoremovementisdetectedwithinapre-selectedtime,then
theWACEPIRswitchwillturntheloadoff.Thistimelagcanbeset
viatheTIMEadjusterto10seconds,20seconds,40seconds,80
seconds, 2 minutes 30 seconds, 5 minutes,10 minutes, 20 minutes
or 40 minutes (diagram A).
The WACEPIR also incorporates a sensitivity adjuster.
Turn fully
clockwiseformaximumrangeandsensitivityofthepersondetector.
SeveralWACEPIRunitscanbewiredinparallel(diagramE).
Loading limits
Theswitchshouldonlybeconnectedtoa230V50HzACsupply.
ThesePIRswitchescanswitchupto:
6amps(1500W)ofresistiveloads.
6amps(1500W)ofuorescentloads.
3amps(750W)ofelectronicandwirewoundtransformerloads.
2amps(500W)ofCFL,2Dlamps,LEDDriversandLEDlamps
andttings.
1amp(250W)offans
Minimumload2Wresistive,suitableformostenergysavinglamps,
LEDsandemergencyttings.
08/04/15 INS948 WACEPIR
Lux and Time set-up
Forconvenience,ensurethattheTIMEissettotheminimumwhen
settinguptheLUXlevel.AfterwardssettheTIMEandSENStovalues
suitablefortheapplication.
TheLUXis bestsetupwhenthelocalambient lightisclosetothe
minimumdesiredlightlevel.WiththeLUXsetfullyclockwisewaitforthe
WACEPIRtoswitchoff.RotatetheLUXadjusterslowlyanticlockwise
(- to +), whilst waving your hand approximately 1m in front of the
WACEPIR,untiltheloadswitcheson.
The load will not switch on:
• TheLUXadjusterissettoolowandisinhibitingtheswitch.
• ThemovingbodyisnotemittingmoreIRthanthebackground.
  (Personwearinginsulatingclothinginawarmenvironment)
• PersonistoofarfromthePIRswitch,seedetectiondiagram.
• Personismovingunusuallyslowly(perhapswhentesting).
The load switches on when nobody is present:
• Heatercausinginfra-redvariationsinasmallcoldroom.
  Reducethesensitivityadjusterorre-sitetheWACEPIR.
• PleasecontactDANLERSforfurthertechnicalsupport.
Fault nding

1.Pleasereadthesenotescarefullybeforecommencingwork.
Incaseofdoubtpleaseconsultaqualiedelectrician.
Makesurethepowerisisolatedfromthecircuit.
2.The switch should be placed facing the area where activity is
expected,ifwallmountedatbetween1mand1.8mhigh(diagram
C).Ifthephotocelloverridefacilityisrequired,theswitchmustbe
sitedinapositionwherethedaylightcangivegreaterillumination
thanthearticiallight.
3.Connect the WACEPIR as:
L Livein
N Neutral in
SL Switchedlineout
 AsshowninthediagramDopposite.
4.A few WACEPIRproducts can bewiredin parallel tocontrol the
same load (diagram E)
5.Therearethreeadjustmentsontheundersideedgeoftheswitch:
TIME,LUXandSENS(sensitivity)(diagramA)
6.Whenthewiringhasbeencompletedandveried,switchonthesupply
and test operation.
WhenthePIRispoweredup,itwillswitchontheloadfor1minute,the
loadwillthenswitchoffandthePIRwillenteritsOperatingMode.Ifa
manualoverride-offswitchispositionedbeforethePIRinthecircuit
(diagramsD&E,note1)itwilldothiseachtimethewallswitchis
switchedon.Alternatively,ifthe wall switch is placed after thePIR
(diagramsD&E,note2)itwillnotenterthestart-upmodeeachtime.
Installation procedure
A: Adjusting time, lux and sensitivity
D: Wiring diagram, single PIR
L
load
Note 1: Optional manual wall switch for overriding off.
Note 2: Alternative position for optional wall switch
N
230 VAC
L
N
SL
load
Note 1: Optional manual wall switch for overriding off
Note 2: Alternative position for optional wall switch.
L N
230 VAC
L
N
SL
L
N
SL
L
N
SL
E: Wiring diagram, multiple PIRs
up to 5m
up to 7m
Strong detection zone i.e. person moving arm or walking towards PIR
Secondary detection zone i.e. person walking perpendicular to PIR
For optimum coverage recommended mounting height: 2.4 to 5m
Up to 5m Up to 10m
WACE PIR
Strong Detection Zone i.e. person walking towards switch
Secondary Detection Zone i.e. person walking perpendicular to switch
60°
120°
Up to 5m Up to 10m
Strong Detection Zone i.e. person walking towards switch
Secondary Detection Zone i.e. person walking perpendicular to switch
45°
90°
WACE PIR
(Spindles
facing
down)
Plan view
Side elevation
B: Detection diagram, Ceiling mounted C: Detection diagram, Wall mounted
TIME
min max
LUX
max min
SENS
min max
Typical settings
30 LUX
1000 LUX
PHOTOCELL
INACTIVE
40m
20m
10m
5m
2.5m
80s
10s
20s
40s
100%
50%