Delfield N8831 User manual

Short Form
Specifications
Top shall be one-piece 18-gauge
stainless steel, with .60" (1.524cm)
overhang around perimeter and die-
stamped 19.87" x 11.87" (50.5 cm
x 30.2 cm) openings with depressed
edges. Formed well below each
opening shall be 6.25" (15.9 cm)
deep. Each well shall have an
individual infinate temperature control
and 1000 watt heating element
attached to bottom of well. Unit is
equipped with .5" drains, (one per
well located in right rear corner
.5" female N.P.T.) manifold and .5"
ball valve. Exterior housing shall be
20-gauge galvanized steel. Unit shall
be insulated on sides and between
wells with 1.00" (2.5 cm) fiberglass;
bottom shall have 2.00" (5.1 cm)
blanket insulation.
Unit shall have all individual controls
wired to a control panel for mounting
in counter or at a remote location; 4'
(1.2 m) length of wiring and conduit
are provided. Unit shall have a three-
wire electrical junction box to allow
hard-wiring at installation.
Optional Accessories and
Modifications:
• Adapter plates and bars
• Single- or double-service flip-up
sneezeguards
• Telescoping covers
• Omit drains and manifold
Drop-In Individually-Controlled Electric Food Wells
Model N8787-D
N8700-D
MODEL COUNTER CUTOUT CONTROL PANEL # OF VOLTS/HERTZ/ SHIP
NUMBER A DIMENSIONS CUTOUT DIMENSIONS FOOD WELLS PHASE AMPS WEIGHT
N8717-D
17.88” (45.4cm) 16.88” X 25” (37.8cm x 58.4cm) 4.62” x 7” (11.7cm x 17.8cm) 1 115/60/1 8.3 39 lbs/ 17 kg
N8731-D
31.75” (80.6cm) 30.75” x 25” (73cm x 58.4cm) 4.62” x 10.31” (11.7cm x 26.2cm) 2 115/60/1 17.0 119 lbs/ 54 kg
N8745-D
45.63” (115.9cm) 44.63” x 25” (108.3cm x 58.4cm) 4.62” x 14.5” (11.7cm x 36.8cm) 3 208-230/60/1 15.7 150 lbs/ 68 kg
N8759-D
59.5” (151.1cm) 58.5” x 25” (143.5cm x 58.4cm) 4.62” x 18.69” (11.7cm x 47.5cm) 4 208-230/60/1 20.9 170 lbs/ 77 kg
N8773-D
73.38” (186.4cm) 72.38” x 25” (178.8cm x 58.4cm) 4.62” x 22.88” (11.7cm x 58.1cm) 5 208-230/60/1 26.1 196 lbs/ 88 kg
N8787-D
87.25” (221.4cm) 86.25” x 25” (214cm x 58.4cm) 4.62” x 27” (11.7cm x 68.6cm) 6 208-230/60/1 31.3 232 lbs/ 104 kg
Mechanical Data — Standard Unit
The Delfield Company, 980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • [phone] • Fax [phone] • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2002 The Delfield Company. All rights reserved. Printed in U.S.A.
PROJECT _____________________________________
ITEM NUMBER_________________________________
QUANTITY _______________ DATE ________________
APPROVAL____________________________________
NOTE: NOT TO SCALE NOTE: NOT TO SCALE
6.25"
15.9cm
9.12"
23.16cm
19.87"
50.5cm
24.67"
62.66cm
25.87"
66cm
A
A – 1.20"
A – 3.05cm
NOTE: NOT TO SCALE
11.87"
30.2cm
TYPICAL PLAN VIEW
N8700-D MODELS
TYPICAL ELEVATION VIEW
N8700-D MODELS
RIGHT END VIEW
ALL N8700-D MODELS

MODEL COUNTER CUTOUT # OF 12” X 20” VOLTS/HERTZ/ SHIP WEIGHT
NUMBER A B DIMENSIONS PANS HELD PHASE AMPS LBS/KG
N8831
31.75” (80.6cm) 5.91” (15cm) 30.75” X 25” (73cm x 58.4cm) 2 120/60/1 17.0 124/56
N8845
45.63” (115.9cm) 12.84” (32.6cm) 44.63” x 25” (108.3cm x 58.4cm) 3 208-230/60/1 14.4/15.9 150/68
N8859
59.5” (151.1cm) 19.78” (50.2cm) 58.5” x 25” (143.5cm x 58.4cm) 4 208-230/60/1 19.2/21.3 189/85
N8873
73.38” (186.4cm) 26.71” (67.8cm) 72.38” x 25” (183.8cm x 63.5cm) 5 208-230/60/1 24.0/26.6 200/91
N8887
87.25 (221.6cm) 33.65” (85.5cm) 86.25” x 25” (214cm x 58.4cm) 6 208-230/60/1 28.8/31.3 226/102
Short Form
Specifications
Top shall be one-piece 18-gauge stain-
less steel, with .60" (1.524 cm) over-
hang around perimeter. Well shall be
8.00" (20.3 cm) deep, creased to a
1.00" male N.P.T. stainless steel drain.
Unit shall be provided with adapter
bars to allow placement of 12" x 20"
(30.5 cm x 50.8 cm) pans. Unit shall
have the same number of 1000 watt
heating elements as the unit’s 12" x
20" pan capacity, mounted on under-
side of well. Sides shall be insulated
with 1.00" (2.5 cm) fiberglass; bottom
shall have 2.00" (5.1 cm) blanket
insulation. Exterior housing shall be
20-gauge galvanized steel.
Unit shall have a single thermostat
wired to a control panel for mounting
in counter or at a remote location; 2'
(0.6 m) length of wiring and conduit
are provided. Unit shall have a three-
wire electrical junction box to allow
hard-wiring at installation.
Optional Accessories and
Modifications:
• Adapter plates and bars
• Single- or double-service flip-up
sneezeguards
• Telescoping covers
Drop-In Single-Tank Electric Hot Food Wells
Model N8887
Mechanical Data — Standard Unit
19.87"
50.5cm
24.5"
62.23cm
25.87"
65.71cm
A
A – 1.31"
A – 3.33cm
A – 6"
A – 15.2cm
C
L8.00"
20.3 cm
B
NOTE: NOT TO SCALE
NOTE: NOT TO SCALE
8"
20.3cm
11"
27.9cm
NOTE: NOT TO SCALE
CONTROL PANEL CUTOUT DIMENSION:
4.62" x 6.00" (11.7 cm x 15.2 cm)
8"
20.3cm
TYPICAL PLAN VIEW
N8800 MODELS
TYPICAL ELEVATION VIEW
N8800 MODELS
RIGHT END VIEW
ALL N8800 MODELS
The Delfield Company, 980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • [phone] • Fax [phone] • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2002 The Delfield Company. All rights reserved. Printed in U.S.A.
DS87_8800 01/02
N8800
PROJECT _____________________________________
ITEM NUMBER_________________________________
QUANTITY _______________ DATE ________________
APPROVAL____________________________________