Deltech Fitness DF142 User manual

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
ASSEMBLY INSTRUCTIONS FOR
THE DF142 OLYMPIC BENCH
800 LB WEIGHT CAPACITY WEIGHT AND USER IN THE BENCH
PRESS POSITION. 650 LB CAPACITY IN THE INCLINE POSITION
WEIGHT AND USER. 100 LB WEIGHT CAPACITY FOR THE LEG
EXTENSION. 175 LB CAPACITY FOR THE ARM CURL POSITION

TOOLS REQUIRED:
1) 1/2" WRENCH 2) 9/16” WRENCHES
INSTRUCTIONS:
1) FIRST ASSEMBLE THE SEAT SLIDE USING FIGURE “B AND C USING THE
5/16-18 X 1” BOLTS (3). BEFORE INSTALLING ON THE SEAT FRAME.
2) NOW USING FIGURE “A” SLIDE THE FRONT FOOT (7) INTO THE SEAT
FRAME (2) USING THE LOCK PIN (14). NEXT SLIDE THE SEAT ASSEMBLY (3)
ON THE SEAT FRAME (2). INSTALL THE PULL PIN (12) AND THE TIGHTEN
KNOB (13) ON THE SLIDE (3). THEN INSTALL THE PULL PIN (12) ON THE SEAT
FRAME (2).
3) NEXT ATTACH THE MOUNTING FLANGE (6) ONTO THE WEIGHT COLUMN
(1) USING THE 3/8”-16 X 3” BOLTS (8), 3/8” WASHERS, AND 3/8-16 NUTS (9).
NOW ATTACH THE SEAT FRAME ASSEMBLY (2) TO THE WEIGHT COLUMN
(1) USING THE 3/8”-16 X 3” BOLTS (8), 3/8” WASHERS, AND 3/8-16 NUTS (9).
4) INSTALL THE PULL PIN (12) INTO THE WEIGHT COLUMN (1) AND SLIDE
THE WEIGHT BAR HOLDERS (4) INTO THE WEIGHT COLUMN (1). NOW PUSH
THE 1” GRIPS (11) ONTO THE WEIGHT BAR HOLDERS (4) NOTE: THE GRIPS
WILL SLIDE ON EASIER IF YOU MOISTEN THE TUBE WITH A SPONGE
BEFORE INSTALLATION.
5) MAKE SURE ALL THE BOLTS ARE TIGHT BEFORE USE. REMEMBER TO
CHECK THEM PERIODICALLY TO MAKE SURE THEY ALWAYS STAY TIGHT.
FIGURE D
1) ASSEMBLE THE LEG SWING (1) TO THE YOKE POST (2) USING THE 1/2”-13
X 3 1/4” BOLT (5) AND THE 1/2”-13 NUT (6).
2) SLIDE THE PAD TUBES (4) THROUGH THE LEG SWING (1) AND THE YOKE
POST (2). NEXT SLIDE THE PADS (3) ONTO THE LEG PAD TUBES (4). THEN
SECURE THE PADS (3) USING THE MUSHROOM CAP (9).
3) INSTALL THE 1 3/4” SQUARE CAPS (8) INTO THE LEG SWING (1) AND THE
YOKE POST (2). NOW INSTALL THE 1” RD CAP (7) INTO THE LEG SWING (1).
FINALLY INSTALL THE BUMPER (10) ON THE BACK OF THE LEG SWING (1).
FIGURE E
1) ASSEMBLE THE PAD (E) TO THE FRAME (C) USING THE 1/4”-20 X 3/4”
BOLTS (D) AND THE FLAT WASHERS.
2) NEXT SLIDE THE BAR HOLDER (A) ON THE ARM PAD FRAME (C) AND
SCREW IN THE PULL PIN (B).
ASSEMBLY INSTRUCTIONS FOR
THE DF142 OLYMPIC BENCH

WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY EXERCISING ON THIS
EQUIPMENT. THE POSSIBILITY OF RISK CAN BE REDUCED BY ALWAYS FOLLOWING THESE SIMPLE RULES:
1) BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL EXAMINATION
AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU.
2) STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM, PROPER STRETCHING WILL PREPARE YOUR JOINTS AND
MUSCLES FOR EXERCISE AND HELP AVOID INJURIES.
3) IF AT ANY TIME YOU SHOULD FEEL FAINT OR DIZZY, NAUSEOUS OR EXPERIENCE ANY OTHER ABNORMAL SYMP-
TOMS OR DISCOMFORT, DISCONTINUE USE AND CONSULT YOUR DOCTOR.
4) DO NOT USE THIS EQUIPMENT WITHOUT QUALIFIED SUPERVISION AND PROPER TRAINING NEVER WORK OUT ALONE
ALWAYS HAVE A PARTNER.
5) SECURELY TIGHTEN ALL BOLTS AND REGULARLY CHECK TO ENSURE ALL BOLTS HAVE NOT LOOSENED.
6) WEAR GOOD RUBBER SOLE SHOES ONLY DO NOT USE BARE FOOTED OR WITH SOCKS ONLY.
7) DO NOT WEAR LOOSE CLOTHES SUCH AS ROBES, GOWNS, PANTS, LONG SHIRTS OR JEWELRY WITCH COULD BECOME
ENTANGLED IN MOVING PARTS.
8) DO NOT STAND OR KNEEL ON SEAT ALWAYS SIT OR LAY SQUARELY CENTERED.
9) KEEP HEAD, LIMBS AND BODY PARTS CLEAR OF MOVING PARTS AND WEIGHT PLATES.
10) CHILDREN SHOULD NOT USE EXERCISE EQUIPMENT WITHOUT SUPERVISION BECAUSE OF POSSIBILITY OF INJURY
FROM IMPROPER USAGE. THIS EQUIPMENT IS INTENDED FOR HOME USE ONLY.
11) REPLACEMENT OR WORN OR DEFECTIVE PARTS MUST BE REPLACE WITH FACTORY AUTHORIZED PARTS. IF OTHER
THAN FACTORY AUTHORIZED PARTS OR ASSESSORS ARE USED ALL WARRANTIES AND LIABILITIES BECOME VOID.
ADJUSTING THE BACK PAD: RAISE AND LOWER THE BACKREST USING THE
PULL PIN IN THE SEAT SLIDE. MAKE SURE THE PULL PIN IS ENGAGED IN THE
ADJUSTMENT HOLE.
ADJUSTING THE SEAT PAD: RAISE THE SEAT PAD TO THE DESIRED POSITION
BY USING THE PULL PIN THOUGH THE HOLES IN THE BRACKET.
ADJUSTING THE WEIGHT ARMS: RAISE AND LOWER THE WEIGHT ARMS US-
ING THE PULL PIN. MAKE SURE THE PULL PIN IS ENGAGED IN THE ADJUST-
MENT HOLE.
ADJUSTING THE ARM PAD: RAISE AND LOWER THE PAD USING THE PULL PIN.
TURN THE KNOB TO LOOSEN FOR ADJUSTMENT MAKE SURE THE PULL PIN IS
SECURE IN THE ADJUSTMENT HOLE THEN TURN THE KNOB TO TIGHTEN
BEFORE USE.
ADJUSTING THE DECLINE: RAISE AND LOWER THE WEIGHT BENCH USING
THE LOCK PIN IN THE HOLE AT THE DESIRED HEIGHT . MAKE SURE THE LOCK
PIN IS THROUGH BOTH SIDES OF THE TUBE BEFORE USE.
ASSEMBLY INSTRUCTIONS FOR
THE DF142 OLYMPIC BENCH

FIGURE A
(NOTE: THE NUTS USED ON THIS BENCH ARE LOCK
NUTS, THIS MEANS YOU MUST TIGHTEN THEM DOWN
PAST THE PLASTIC INSERT.)
NOTE: #5 INCLINE BAR IS REMOVED FOR THE
FLAT BENCH POSITION
ASSEMBLY INSTRUCTIONS FOR
THE DF142 OLYMPIC BENCH

FIGURE B
FIGURE C
ASSEMBLY INSTRUCTIONS FOR
THE DF142 OLYMPIC BENCH

FIGURE D

FIGURE E
ASSEMBLY INSTRUCTIONS FOR
THE DF142 OLYMPIC BENCH

BOX CONTENTS
PART # DF141-50
BRACKET
QTY 1
PART # DF141-40
FOOT
QTY 1
PART # DF141-70
SLIDE
QTY 1
PART # DF141-30
WEIGHT CRADLE
QTY 2
PART # DF142-10
WEIGHT COLUMN
QTY 1
PART # DF142-60
INCLINE ROD
QTY 1 PART # DF141-20
SEAT FRAME
QTY 1
PART # DF142
HARDWARE PACK
QTY 1
ASSEMBLY INSTRUCTIONS FOR THE
DF141 ULTRA FIT NARROW
PART # DF142
INSTRUCTIONS
QTY 1
PART # COM8014
BACKREST
QTY 1
PART # COM8015
SEAT
QTY 1
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
ASSEMBLY INSTRUCTIONS FOR
THE DF142 OLYMPIC BENCH

BOX CONTENTS
PART # DF105-20
BAR SUPPORT
QTY 1
PART # DF105-10
ARM SUPPORT
QTY 1
PART # COM8016
ARMREST
QTY 1
PART # COM6005
YOKE
QTY 1
4” X 8” ROLLER
PAD
QTY 6
PART # COM7001
LEG PAD TUBE
QTY 3
PART # COM6000
LEG SWING
QTY 1
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
ASSEMBLY INSTRUCTIONS FOR
THE DF142 OLYMPIC BENCH

(2 PCS) 2” SQ. CAP (2 PCS) 3 1/4” LOCK PIN
(6 PCS) 3/8” X 1” TURN KNOB (6 PCS) PULL PIN BALL STYLE
(4 PCS) 1/4” FLAT WASHER (2 PCS) HANDLE GRIP
(1 PCS) 1/2”-13 X 2 3/4” BOLT (12 PCS) 1/2” WASHER
(4 PCS) 5/16” - 18 X 1” BOLT (2 PCS) REDUCERS
(4 PCS) 5/16” WASHER (1 PC) 1” QUICK CLAMP
(6 PCS) 1/2”-13 NUT (3 PCS) 1 3/4” SQ. CAP
(5 PCS) 1/2”-13 X 3” BOLT (1 PC) 1” RD. BUMPER
(6 PCS) MUSHROOM CAP (1 PCS) 1” RD. INSIDE CAP
(4 PCS) 1/4 - 20 X 1” BOLT (1 PC) PULL PIN
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
1/2” 1” 2” 3” 4” 5”1/2” 1/2” 1/2” 1/2”
ASSEMBLY INSTRUCTIONS FOR
THE DF142 OLYMPIC BENCH

SEND TO: DELTECH MANUFACTURING, INC.
3910 OAKLAWN DR.
LOUISVILLE, KY. 40219
ALL ORDERS SHIPPED UPS GROUND.
MAKE CHECK OR MONEY ORDER PAYABLE TO: DELTECH MANUFACTURING
KENTUCKY RESIDENTS ADD 6% SALES TAX. ALLOW 3 WEEKS FOR DELIVERY.
PRICE INCLUDES SHIPPING TO THE CONTIGUOUS UNITED STATES
OR ORDER ONLINE WITH A CREDIT CARD AT WWW.FITNESSDESTINATION.COM
SHIPPING INFORMATION:
QTY SIZE DESCRIPTION COLOR PRICE TOTAL
T - SHIRT WHITE $12.99 EA.
MUSCLE SHIRT BLACK $12.99 EA.
TOTAL
T-SHIRT ORDER FORM
DELTECH FITNESS T - SHIRT
SIZES AVAILABLE ARE M-XXL. THE COLOR
OF THE SHIRTS ARE WHITE. RED AND BLACK
LOGO. ONLY $12.99
DELTECH FITNESS MUSCLE SHIRT
SIZES AVAILABLE M-XXL THE COLOR
AVAILABLE IS BLACK. RED AND WHITE
LOGO. ONLY $12.99