Deltech Fitness DF406 User manual

DF406
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
45 DEGREE
HYPEREXTENSION BENCH
Assembly Manual

ROLLER PAD
TUBE
QTY 1
H
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
BOX CONTENTS
BOTTOM FRAME
QTY 1
AADJUSTMENT ARM
QTY 1
BPAD FRAME
QTY 1
CPAD
QTY 2
D
FRONT FOOT
QTY 1
E
UPPER FRAME
QTY 1
FTUBE FRAME
QTY 1
G
ROLLER PAD
QTY 2
I

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
HARDWARE
SQUARE CAP
QTY 3
L
ROUND CAP
QTY 2
K
SQUARE CAP
QTY 2
JHAND GRIP
QTY 2
M
10MM LOCKNUT
QTY 6
S10MM WASHER
QTY 6
T8MM WASHER
QTY 4
U
MUSHROOM CAP
QTY 2
V
PULL-PIN
QTY 2
OM10 x 75MM
BOLT
QTY 6
PM10 x 65MM
BOLT
QTY 2
Q
M8 x 25MM BOLT
QTY 4
R
REDUCER
QTY 2
N

BOTTOM FRAME ASSEMBLY
TOOLS REQUIRED:
ADJUSTABLE WRENCHES OR SOCKET SET
INSTALL THE BOTTOM FRAME (A) TO THE FRONT FOOT (E) , ALIGNING THE HOLES IN THE FRONT
FLANGE WITH THE HOLES IN THE FOOT.
ASSEMBLE THE BOTTOM FRAME TO THE FRONT FOOT USING THE M10 x 75MM BOLTS (P), M10
WASHERS (T) AND M10 LOCKNUT (S). INSTALL THE 2” ROUND RUBBER CAPS (K) ON THE BOTTOM
FRAME AND THE 2” SQUARE RUBBER CAPS (J) ON THE FRONT FOOT.
A
E
J
J
P
TT
S
K
K

UPPER FRAME ASSEMBLY
ASSEMBLE THE UPPER FRAME (F) TO THE BOTTOM FRAME ASSEMBLY USING THE M10 x 75MM
BOLTS (P), M10 WASHERS (T) AND M10 LOCKNUT (S). INSTALL THE PULL-PINS (0).
T
PF
TS
PS
T
T
N
O
O

PAD FRAME ASSEMBLY
ASSEMBLE THE ADJUSTMENT ARM (B) TO THE PAD FRAME (C) USING THE M10 x 65MM BOLTS
(Q), M10 WASHERS (T) AND M10 LOCKNUT (S). THEN INSTALL THE 2” CAPS (L) .

PAD FRAME ASSEMBLY
ASSEMBLE THE HANDGRIPS (M) TO THE HANDLES.
ASSEMBLE THE PADS (D) TO THE PAD FRAME USING THE M8 x 25MM BOLTS (R) AND M8 WASHERS

INSTALL SQUARE CAP (L) INTO END OF TUBE FRAME (G). INSERT THE ROLLER TUBE (H) TUBE INTO
THE TUBE FRAME (G). INSTALL THE ROLLER PADS (I) ONTO THE TUBE AND INSERT MUSHROOM
CAPS (V) INTO END OF ROLLER TUBE.
LEG HOLD-DOWN ASSEMBLY

INSERT THE PAD FRAME ASSEMBLY AND LEG HOLD-DOWN ASSEMBLY INTO THE UPPER FRAME.
ADJUST AS NECESSARY AND TIGHTEN PULL-PIN KNOBS.
FINALASSEMBLY

WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY
EXERCISING ON THIS EQUIPMENT. THE POSSIBILITY OF RISK CAN BE REDUCED BY ALWAYS
FOLLOWING THESE SIMPLE RULES:
1) BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL
EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU.
2) STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM, PROPER STRETCHING WILL PREPARE YOUR
JOINTS AND MUSCLES FOR EXERCISE AND HELP AVOID INJURIES.
3) IF AT ANY TIME YOU SHOULD FEEL FAINT OR DIZZY, NAUSEOUS OR EXPERIENCE ANY OTHER
ABNORMAL SYMPTOMS OR DISCOMFORT, DISCONTINUE USE AND CONSULT YOUR DOCTOR.
4) DO NOT USE THIS EQUIPMENT WITHOUT QUALIFIED SUPERVISION AND PROPER TRAINING NEVER
WORK OUT ALONE ALWAYS HAVE A PARTNER.
5) SECURELY TIGHTEN ALL BOLTS AND REGULARLY CHECK TO ENSURE ALL BOLTS HAVE NOT
LOOSENED.
6) WEAR GOOD RUBBER SOLE SHOES ONLY DO NOT USE BARE FOOTED OR WITH SOCKS ONLY.
7) DO NOT WEAR LOOSE CLOTHES SUCH AS ROBES, GOWNS, PANTS, LONG SHIRTS OR JEWELRY WITCH
COULD BECOME ENTANGLED IN MOVING PARTS.
8) DO NOT STAND OR KNEEL ON SEAT ALWAYS SIT OR LAY SQUARELY CENTERED.
9) KEEP HEAD, LIMBS AND BODY PARTS CLEAR OF MOVING PARTS AND WEIGHT PLATES.
10) CHILDREN SHOULD NOT USE EXERCISE EQUIPMENT WITHOUT SUPERVISION BECAUSE OF
POSSIBILITY OF INJURY FROM IMPROPER USAGE. THIS EQUIPMENT IS INTENDED FOR HOME USE ONLY.
11) REPLACEMENT OR WORN OR DEFECTIVE PARTS MUST BE REPLACE WITH FACTORY AUTHORIZED
PARTS. IF OTHER THAN FACTORY AUTHORIZED PARTS OR ASSESSORS ARE USED ALL WARRANTIES
AND LIABILITIES BECOME VOID.
SAFETY NOTICE