Deltech Fitness DF908 User manual

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
LAT PULLDOWN MACHINE
WITH 200 LB WEIGHT STACK
Assembly Manual
Assembly Video Available
Simply scan the QR code below
on your phone’s camera to access
the video
[phone]
DF908

LAT MACHINE COMPONENTS
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
REAR SUPPORT
QTY 1
A
FRONT SUPPORT
QTY 1
B
BOTTOM FRAME
QTY 1
C
REVOLVING CHROME
ROW BAR
QTY 1
F
LAT CABLE
QTY 2
G
FOOT PLATE
QTY 1
D
FOOT REST
QTY 1
E

LAT BAR
QTY 1
H
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
SEAT SUPPORT
QTY 1
L
SEAT BRACKET
QTY 1
K
UPPER PULLEY
FRAME
QTY 1
I
SEAT PAD
QTY 1
J
REAR CROSSMEMBER
QTY 1
O
HOLD-DOWN SUPPORT
QTY 1
N
HOLD-DOWN
TUBE
M
ROLLER PAD
QTY 2
P
FLANGE
QTY 2
Q
BOTTOM PULLEY
FRAME
QTY 1
R
LAT MACHINE COMPONENTS

S
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
BOTTOM SUPPORT
QTY 1
UPPER PULLEY
FRAME
QTY 1
WEIGHT STACK COMPONENTS
WEIGHT STACK
RODS
QTY 2
WEIGHT STACK
(19) 10 LB. PLATES
QTY 1
WEIGHT STACK
TOP PLATE
QTY 1
SELECTOR ROD
QTY 1
T U V
W X

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
HARDWARE
MUSHROOM CAP
QTY 2
4-1/2” PULLEY
QTY 3
3-1/2” PULLEY
QTY 3
PULLEY BUSHING
QTY 6
SNAP HOOK
QTY 6
CHAIN
QTY 2
M12 x 70MM BOLT
QTY 4
FF
M10 x 45MM BOLT
QTY 4
HH
I I
M10 x 20MM BOLT
QTY 4
JJ
M10 x 70MM
FLAT HEAD BOLT
QTY 3
RUBBER SHOE
QTY 5
Z
M10 x 70MM BOLT
QTY 3
GG
KK
M10 x 65MM
CARRIAGE BOLT
QTY 9
Y AA BB
CC DD EE

OO
M10 LOCKNUT
QTY 21
M12 WASHER
QTY 8
LL
M10 WASHER
QTY 26
MM NN
M12 LOCKNUT
QTY 4
SPRING PIN
QTY 1
PP
RUBBER DOUGHNUTS
QTY 2
QQ
WEIGHT STACK
ADJUSTMENT PIN
QTY 1
RR
WEIGHT STACK
BOLT
QTY 1
SS
HARDWARE

LAY BOTTOM FRAME (C) ON ITS SIDE ON LEVEL FLOOR. INSTALL FRONT & REAR
SUPPORTS (A), (B) TO BOTTOM FRAME (C) USING THE M10 x 65MM
CARRIAGE BOLTS (KK), M10 WASHERS (MM), AND M10 LOCKNUTS (OO).
INSTALL BOTTOM PULLEY FRAME (R), HOLD-DOWN SUPPORT (M), AND SEAT
SUPPORT (J) TO BOTTOM FRAME (C) USING THE M10 x 65MM CARRIAGE BOLTS
(KK), M10 WASHERS (MM), AND M10 LOCKNUTS (OO).
TOOLS REQUIRED:
METRIC WRENCHES OR SOCKET SET
Some components may be pre-installed
from the factory
(NOTE: THE NUTS USED ON THIS
BENCH ARE LOCK NUTS, THIS MEANS
YOU MUST TIGHTEN THEM DOWN
PAST THE PLASTIC INSERT.)
KK
OO
MM
C
L
N
B
A
R

ROTATE THE ASSEMBLY TO THE UPRIGHT POSITION AND SLIDE THE REAR
CROSSMEMBER (O) INTO PLACE AND INSTALL TO THE BOTTOM FRAME USING
THE M12 x 70MM BOLTS (FF), M12 WASHERS (LL), AND M12 LOCKNUTS (NN).
INSTALL THE RUBBER BOOTS (Z) OVER THE ENDS OF THE CROSSMEMBER.
ATTACH THE FOOT PLATE (D) AND FOOT REST (E) TO THE BOTTOM FRAME
USING M10 x 70 MM FLAT HEAD BOLTS (JJ), M10 WASHERS (MM), AND M10
LOCKNUTS (OO).
FF
Z
Z
O
LL
LL
NN
JJ
D
E
OO
MM

ATTACH THE SEAT PAD (J) TO THE SEAT BRACKET (K) USING THE M10 x 20MM
BOLTS (II) AND M10 FLAT WASHERS (MM). THEN SLIDE THE SEAT BRACKET (K)
INTO THE SEAT SUPPORT (L).
SEAT FRAME ASSEMBLY
J
K
I I
MM
L

SLIDE THE HOLD-DOWN TUBE (M) INTO THE HOLD-DOWN SUPPORT (N) . LOCK
INTO PLACE WITH PULL-PIN.
SLIDE THE ROLLER PADS (P) OVER THE LEG PAD TUBE AND INSERT THE MUSH-
ROOM CAPS (Y). TAP INTO PLACE WITH A RUBBER HAMMER.
LEG HOLD DOWN ASSEMBLY
M
N
Y
P
S
Y

BOTTOM PULLEY FRAME ASSEMBLY
ASSEMBLE THE 4 ½” PULLEY (AA) INTO THE BOTTOM PULLEY FRAME (R) USING
THE M10 x 45MM BOLT (HH), M10 WASHERS (MM), AND M10 LOCKNUT (OO).
R
OO
AA
MM
HH
MM

ASSEMBLE THE UPPER PULLEY FRAME (I) ONTO THE FRONT AND REAR SUPPORTS
USING THE M12 x 70MM BOLTS(FF), AND M12 WASHERS (LL).
DO NOT INSTALL WASHERS AND LOCKNUTS ON BOLTS AT THIS TIME.
LL
LL
FF
FF
I

UPPER PULLEY FRAME INSTALLATION
INSTALL THE UPPER PULLEY ASSEMBLY (T) TO THE FRONT AND REAR SUPPORT USING
M12 WASHERS (LL), AND M12 LOCKNUTS (NN). DO NOT TIGHTEN AT THIS TIME.
T
NN
LL

WEIGHT STACK FRAME ASSEMBLY
INSTALL THE RUBBER SHOES (LL) ON TO THE BOTTOM SUPPORT(S). ATTACH THE BOTTOM
SUPPORT (S) TO THE LAT MACHINE USING THE M10 x 70MM BOLTS (GG) M10 FLAT WASHERS
(MM) AND THE M10 LOCK NUTS (OO).
LL
LL
MM
OO
MM
OO
MM
GG
S

WEIGHT STACK ASSEMBLY
INSTALL THE RUBBER DOUGHNUTS (QQ) ONTO THE BOTTOM OF THE WEIGHT STACK RODS
(U) , LEAVING APPROXIMATELY 2” PROTRUDING. INSERT THE WEIGHT STACK RODS INTO THE
TWO OUTER HOLES IN THE BOTTOM FRAME.
QQ
U

TOP WEIGHT PLATE ASSEMBLY
INSERT SELECTOR ROD (W) INTO CENTER HOLE OF TOP PLATE (X) ALIGNING TOP HOLE OF
SELECTOR ROD WITH SPRING PIN HOLE. INSERT SPRING PIN (PP) AND TAP WITH HAMMER
UNTIL FLUSH WITH SURFACE.
SCREW WEIGHT STACK BOLT (SS) INTO WEIGHT STACK TOP PLATE (X).
PP
X
W
SS

WEIGHT STACK ASSEMBLY
LEAN WEIGHT STACK RODS OUT SLIGHTLY AND BEGIN INSTALLING WEIGHT STACK PLATES
(V), USING TWO OUTER HOLES ON EACH WEIGHT STACK PLATE. SLIDE EACH WEGIHT STACK
DOWN BEFORE INSTALLING THE NEXT. THERE ARE 19 WEIGHT STACK PLATES.
V

WEIGHT STACK ASSEMBLY
INSTALL TOP WEIGHT PLATE ASSEMBLY USING TWO OUTER HOLES OVER WEIGHT STACK
RODS. SLIDE DOWN AND INSERT SELECTOR ROD INTO WEIGHT PLATE STACK.

WEIGHT STACK ASSEMBLY
ROTATE WEIGHT STACK RODS UP TOWARDS THE UPPER PULLEY ASSEMBLY. INSTALL
M10 x 20MM BOLTS (II) INTO TOP OF WEIGHT STACK RODS.
I I

UPPER CABLE INSTALLATION
BOTH CABLES ARE THE SAME LENGTH.
STARTING WITH THE CABLE END WITHOUT THE BALL, INSERT CABLE INTO FRONT
OPENING OF THE UPPER PULLEY FRAME AND FEED IT TOWARDS THE BACK. PULL CABLE
END OUT THROUGH REAR OPENING.