Deltech Fitness DF908 User manual

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
The DF908 consists of the DF906 Lat
Machine and the DF935 Stack Kit
ASSEMBLY INSTRUCTIONS FOR
THE DF908 STACK LOADED LAT
MACHINE

BOX CONTENTS
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
REAR SUPPORT
QTY 1
A
FRONT SUPPORT
QTY 1
B
BOTTOM FRAME
QTY 1
C
REVOLVING CHROME
ROW BAR
QTY 1
DLAT CABLE
QTY 2
E
FOOT PLATE
QTY 1
C1
FOOT REST
QTY 1
C2

LAT BAR
QTY 1
F
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
BOX CONTENTS
SEAT SUPPORT
QTY 1
J
SEAT BRACKET
QTY 1
I
UPPER PULLEY
FRAME
QTY 1
G
SEAT PAD
QTY 1
H
REAR CROSSMEMBER
QTY 1
N
HOLD-DOWN SUPPORT
QTY 1
M
HOLD-DOWN
TUBE
L
WEIGHT SLIDE
QTY 1
K
ROLLER PAD
QTY 2
P
FLANGE
QTY 2
Q
BOTTOM PULLEY
FRAME
QTY 1
R

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
HARDWARE
S
MUSHROOM CAP
QTY 2 4-1/2” PULLEY
QTY 3
U3-1/2” PULLEY
QTY 3
PULLEY BUSHING
QTY 4 SNAP HOOK QTY 6 CHAIN
QTY 2
M12 x 70MM BOLT
QTY 2
AA
M10 x 45MM BOLT
QTY 4
DD
EE
M10 x 20MM BOLT
QTY 2
FF
M10 x 70MM
FLAT HEAD BOLT
QTY 3
RUBBER SHOE
QTY 2
TV
WXY
M12 x 65MM BOLT
QTY 2
BB
M10 x 70MM BOLT
QTY 2
CC
GG
M10 x 65MM
CARRIAGE BOLT
QTY 9

HARDWARE
KK
M10 LOCKNUT
QTY 19
M12 WASHER
QTY 8
HH
M10 WASHER
QTY 20
I I JJ
M12 LOCKNUT
QTY 4

(SEE INSET) ASSEMBLE THE 4 ½” PULLEY (U) INTO THE BOTTOM PULLEY FRAME
(R) USING THE M10 x 45MM BOLT (DD), M10 WASHERS (II), AND M10 LOCKNUT
(KK).
INSTALL TO BOTTOM FRAME (C) USING THE M10 x 65MM CARRIAGE BOLTS (GG),
M10 WASHERS (II), AND M10 LOCKNUTS (KK).
ATTACH THE REAT CROSSMEMBER (N) TO THE BOTTOM FRAME (C) USING THE
M12 x 70MM BOLTS (AA), M12 WASHERS (HH), AND M12 LOCKNUTS (JJ). INSTALL
THE RUBBER BOOTS (T) OVER THE ENDS OF THE CROSSMEMBER.
ATTACH THE FOOT PLATE (C2) AND FOOT REST (C1) TO THE BOTTOM FRAME (C)
USING M10 x 70 MM FLAT HEAD BOLTS (FF), M10 WASHERS (II), AND M10 LOCK-
NUTS (KK).
BOTTOM FRAME ASSEMBLY
TOOLS REQUIRED:
METRIC WRENCHES OR SOCKET SET
Some components may be pre-installed
from the factory
(NOTE: THE NUTS USED ON THIS
BENCH ARE LOCK NUTS, THIS MEANS
YOU MUST TIGHTEN THEM DOWN
PAST THE PLASTIC INSERT.)
U
DD I I
I I
R
KK
AA
N
HH
HH
T
T
C
I I
KK
JJ
GG
I I
KK
I I
KK
C2
C2
FF

ATTACH THE SEAT PAD (H) TO THE SEAT BRACKET (I) USING THE M10 x 20MM
BOLTS (EE) AND M10 FLAT WASHERS (II). THEN SLIDE THE SEAT BRACKET (I)
INTO THE SEAT SUPPORT (J).
(WAIT TO COMPLETE THE FOLLOWING STEP UNTIL THE CABLES ARE INSTALLED)
INSTALL THE 4 ½” PULLEY (U) INTO THE SEAT SUPPORT TUBE (J) USING THE
M10 x 45MM BOLT (DD) , M10 WASHERS (II), AND M10 LOCK NUT (KK).
SEAT FRAME ASSEMBLY
H
I
EE
I I
J
V
DD I I
I I
KK

SLIDE THE HOLD-DOWN TUBE (L) INTO THE HOLD-DOWN SUPPORT (M) . LOCK
INTO PLACE WITH PULL-PIN.
SLIDE THE ROLLER PADS (P) OVER THE LEG PAD TUBE AND INSERT THE MUSH-
ROOM CAPS (S). TAP INTO PLACE WITH A RUBBER HAMMER.
LEG HOLD DOWN ASSEMBLY
L
M
S
P
S
P

FLOATING PULLEYASSEMBLY
ASSEMBLE THE FLOATING PULLEY ASSEMBLY BY USING 4-1/2” PULLEYS (U),
FLANGES (Q), M10 x 45MM BOLTS (DD), M10 WASHERS (II), AND M10 LOCKNUTS (KK).
I I
I I
KK
Q
EE
U

UPPER PULLEY FRAME ASSEMBLY
INSTALL THE FRONT 3-1/2” PULLY (V) INTO THE UPPER PULLEY FRAME (G) USING THE
M10 x 70MM BOLT (CC), PULLEY BUSHINGS (W), AND M10 LOCKNUT (KK). REPEAT
FOR REAR PULLEY.
KK
W
W
V
CC
G
CC W
W
KK
V

ASSEMBLE THE UPPER PULLEY FRAME ASSEMBLY ONTO THE FRONT AND BACK SUP-
PORTS (A,B) USING THE M12 x 65MM BOLTS(BB), M12 WASHERS (HH), AND M12 LOCK-
NUTS (JJ).
MAIN FRAME ASSEMBLY
B
A
HH JJ
HH
BB
JJ
HH
HH
BB
K

LAY THE BOTTOM FRAME ASSEMBLY ON ITS SIDE. ATTACH THE MAIN FRAME
ASSEMBLY, THE LEG HOLDDOWN ASSEMBLY, AND THE SEAT FRAME ASSEMBLY
USING THE M10 x 65MM CARRIAGE BOLTS (GG), M10 WASHERS (II), AND M10
LOCKNUTS (KK).
FINALASSEMBLY
BOTTOM FRAME ASSY
MAIN FRAME ASSY
LEG HOLDDOWN ASSY
SEAT FRAME ASSY
DD
I I
KK
I I
KK
KK
KK
KK I I
I I
I I
I I
I I
KK
KK

ASSEMBLY INSTRUCTIONS FOR
THE DF935 STACK KIT
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
BOTTOM SUPPORT
QTY 1
A
UPPER SUPPORT
ASSY
QTY 1
B
DF935 WEIGHT STACK
BOX CONTENTS
HARDWARE
PACK
QTY 1
CHROME ROD
QTY 2
C
SELECTOR ROD/ TOP
PLATE ASSEMBLY
(10 LBS.)
QTY 1
D
WEIGHT STACK
(19) 10 LB. PLATES
QTY 1
E

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
RUBBER SHOE
QTY 3
F
DF935 WEIGHT STACK
HARDWARE
M10 x 70MM BOLT
QTY 2
G
WEIGHT STACK
ADJUSTMENT PIN
QTY 1
KRUBBER DOUGHNUTS
QTY 2
L
M10 WASHER
QTY 4
HM10 LOCKNUT
QTY 2
I
3/8” x 1” BOLT
QTY 2
J

LOWER FRAME ASSEMBLY
F
F
B
G
H
H
H
I
I
INSTALL THE RUBBER CAPS (F) ONTO THE BOTTOM SUPPORT (B). ATTACH THE BOTTOM
SUPPORT (B) TO THE LAT MACHINE USING THE M10 x 70MM BOLTS (G), M10 WASHERS, AND
M10 LOCKNUTS (I).

WEIGHT STACK ASSEMBLY
INSTALL THE RUBBER DOUGHNUTS (L) ONTO THE BOTTOM OF THE CHROME RODS (C) ,
LEAVING APPROXIMATELY 2” PROTRUDING. INSERT THE CHROME RODS INTO THE TWO
OUTER HOLES IN THE BOTTOM SUPPORT.
ASSEMBLE THE WEIGHT STACK (E) BY SLIDING EACH PLATE OVER THE CHROME RODS (C)
AND ON TO THE BOTTOM SUPPORT.
SLIDE THE SELECTOR ROD/TOP PLATE ASSEMBLY (D) OVER THE CHROME RODS (C) AND
THROUGH THE WEIGHT STACK (E). INSERT THE WEIGHT STACK ADJUSTMENT PIN (K) INTO
THE WEIGHT STACK (E).
D
E
K
C
L

WEIGHT STACK ASSEMBLY
INSTALL THE UPPER SUPPORT ASSEMBLY (B) TO THE LAT MACHINE USING THE M10 x 25MM
BOLTS AND WASHERS YOU REMOVED IN THE PREVIOUS STEP.
ATTACH THE UPPER SUPPORT FRAME ASSEMBLY TO THE CHROME RODS USING 3/8” x 1”
BOLTS (M).
WEIGHT STACK ASSEMBLY
BM
G
B
REMOVE THE M10 x 25MM BOLTS AND WASHERS FROM THE FRONT AND REAR SUPPORT.
M
G
H

INSTALL UPPER CABLE OVER FRONT PULLEY, BACK TO REAR PULLEY, DOWN
TO TOP PULLEY OF FLOATING PULLEYASSEMBLY, UP TO STACK ASSEMBLY
PULLEYAND DOWN TO SELECTOR ROD ASSEMBLY. ATTACH 8MM SNAP HOOK
TO END OF CABLE AND THEN TO SELECTOR ROD BRACKET.
NOTE: UPPER CABLE IS SHORTER
THAN THE BOTTOM CABLE
UPPER CABLE INSTALLATION
UPPER PULLEY FRAME REMOVED
FOR CLARITY
FLOATING PULLEY
ASSEMBLY

LOWER CABLE INSTALLATION
INSTALL LOWER CABLE UNDER FRONT PULLEY, THROUGH SEAT FRAME, LEG
HOLD DOWN FRAME, FRAME POLE, AND BACK TO REAR PULLEY. CONTINUE
UPAND OVER LOWER PULLEY OF FLOATING PULLEYASSEMBLY. ATTACH SNAP
HOOK TO END OF CABLE AND THEN TO CHAIN. ATTACH SNAP HOOK TO THE
OTHER END OF THE CHAIN AND THEN TO FRAME POLE BRACKET. SNAP HOOK
MAY NEED TO BE MOVED TO A HIGHER LINK ON THE CHAIN TO MAKE SURE
CABLE IS TIGHT. ATTACH LOWER ROW BAR TO THE OTHER END OF THE
CABLE, ORATTACH THE OTHER CHAIN TO EXTEND REACH.
FLOATING PULLEY
ASSEMBLY