Deltech Fitness DF4900 User manual

ASSEMBLY INSTRUCTIONS FOR
THE DF4900 LINEAR BEARING
SMITH MACHINE
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]

DF4900
BOX CONTENTS
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
A
LH UPRIGHT
QTY 1
B
RH UPRIGHT
QTY 1
D
RH REAR SUPPORT
QTY 1
C
LH REAR SUPPORT
QTY 1
E
LH FOOT
QTY 1
F
RH FOOT
QTY 1
G
CROSSMEMBER
QTY 1
H
TOP FRAME
QTY 1
PULL-UP BAR
QTY 1
I

M
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
DF4900
BOX CONTENTS
SMITH BAR
QTY 1
JGUIDE ROD
QTY 2
KWEIGHT SLEEVE
QTY 2
RH & LH SAFETY
CATCH
QTY 1 EACH
L
RH & LH SMITH BAR COLLAR
QTY 1 EACH
N
LH & RH GUIDE ROD COLLAR
QTY 1 EACH
O

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
DF4900
HARDWARE
RUBBER SHOE
QTY 4 2” SQUARE CAP QTY 2
(factory installed)
P1-3/4” ROUND CAP
QTY 4
(factory installed)
QRUBBER DONUT
QTY 2
R
PULL-UP BAR BOLT
QTY 2
S
M12 x 90MM BOLT
QTY 20
U
M12 LOCKNUT
QTY 20
M12 WASHER
QTY 40
CHROME SPRING
QTY 2
AA
M10 LOCKNUT
QTY 8
M10 WASHER
QTY 16
TWEIGHT SLEEVE
BOLT
QTY 2
M10 x 25MM BOLT
QTY 8
VW
XYZ
HEX WRENCH
QTY 1 CORNER FLANGE
QTY 2
BB CC DD

(NOTE: THE NUTS USED ON
THIS PRODUCT ARE LOCK
NUTS, THIS MEANS YOU
MUST TIGHTEN THEM DOWN
PAST THE PLASTIC INSERT)
FRAME ASSEMBLY
V
X
A
XZ
XZ
E
C
VX
VX
P
X
G
Z
ZX
P
ZX
F
XV
D
P
XV
B
XZ
V
X
ASSEMBLE THE LH FOOT (E), RH FOOT (F), CROSS MEMBER (G), AND THE LEFT AND RIGHT REAR
SUPPORTS (C) AND (D), USING THE M12 x 90MM BOLTS (V), M12 WASHERS (X), AND M12 LOCK-
NUTS (Z). (LEAVE THE BOLTS HAND TIGHTENED AT THIS TIME)
SLIDE THE RUBBER SHOES (P) ONTO THE RH AND LH FEET (E) & (F).
ASSEMBLE THE RH AND LH UPRIGHTS (A) & (B) TO THE LH AND RH FEET (E) & (F) USING THE
M12 x 90MM BOLTS (V), M12 WASHERS (X), AND M12 LOCKNUTS (Z).
ASSEMBLE THE RH AND LH UPRIGHTS (A) & (B) TO THE REAR SUPPORTS (C) & (D) USING THE
M12 x 90MM BOLTS (V), M12 WASHERS (X), AND M12 LOCKNUTS (Z).

SMITH BAR ASSEMBLY
SLIDE THE ASSEMBLY ONTO THE SMITH BAR (J). REPEAT FOR RH ASSEMBLY.
ASSEMBLE RH SMITH BAR COLLAR (M) AND GUIDE ROD COLLAR (N) USING THE M10 x 25MM
BOLTS (W), M10 WASHERS (Y), AND M10 LOCKNUTS (AA). REPEAT FOR RH ASSEMBLY.
W
YMN
YAA
RIGHT SIDE ASSEMBLY HAS STOP PIN
J

GUIDE BAR INSTALLATION
INSERT THE GUIDE RODS (K) INTO THE RETAINERS AT THE BOTTOM. SLIDE THE RUBBER DONUTS (S)
ONTO THE GUIDE RODS AND MOVE TO THE BOTTOM. INSTALL THE RH AND LH SAFETY CATCHES (O)
AND HOOK ONTO ONE OF THE CATCH PINS TO SUPPORT THE GUIDE RODS. SLIDE THE CHROME
SPRINGS (BB) ONTO THE GUIDE RODS (K).
K
SMITH BAR ASSEMBLY
MAKING SURE THAT THE HOOKS ARE FACING TOWARDS THE BACK, INSTALL THE SMITH BAR
ASSEMBLY ONTO THE GUIDE BARS AND LOWER UNTIL IT RESTS ON THE SAFETY CATCHES. LIFT
SMITH BAR, ROTATE BACKWARDS AND HOOK ONTO ONE OF THE BAR CATCH PINS.
K
S
S
O
O
BB
BB

INSTALL WEIGHT SLEEVE (L) WITH WEIGHT SLEEVE BOLT (U) ONTO SMITH BAR (J) AND TIGHTEN
WITH SUPPLIED HEX WRENCH. REPEAT FOR OPPOSITE SIDE.
U
L
J
TOP FRAME INSTALLATION
INSTALL THE TOP FRAME (H) ONTO THE UPRIGHTS AND GUIDE RODS.
H
SMITH BAR ASSEMBLY

ATTACH THE TOP FRAME TO THE UPRIGHTS USING THE M12 x 90MM BOLTS (V), M12 WASHERS (X),
CORNER FLANGES (DD), AND M12 LOCKNUTS (Z). REPEAT FOR OPPOSITE SIDE.
V
X
XZ
DD
TOP FRAME INSTALLATION
TOP FRAME INSTALLATION
ATTACH THE PULL-UP BAR (I) TO THE TOP FRAME USING THE PULL-UP BAR BOLTS (T), AND M12
WASHERS (X).
MAKE SURE ALL THE BOLTS ARE TIGHT BEFORE USING. CHECK THEM PERIODICALLY TO
ENSURE THE BOLTS STAY TIGHT. HAVE A GOOD WORKOUT!
I
T
X

GUIDE BAR ADJUSTMENT
THE GUIDE BAR RETAINERS ARE SLOTTED TO ALLOW FOR ADJUSTMENT. USING THE SUPPLIED
HEX WRENCH, TIGHTEN THE SET SCREWS ON BOTH SIDES OF THE BOTTOM RETAINER. HOLD A
LEVEL AGAINST THE GUIDE ROD TO ENSURE IT IS LEVEL. IF NECESSARY ADJUST THE SET
SCREWS ON THE UPPER RETAINER. REPEAT FOR OPPOSITE SIDE. ( ADJUSTING THE DISTANCE
BETWEEN THE GUIDE RODS IS NOT NECESSARY AS THE SMITH BAR HAS A FLOATING SYSTEM
TO ALLOW FOR VARIANCES )

WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY
EXERCISING ON THIS EQUIPMENT. THE POSSIBILITY OF RISK CAN BE REDUCED BY ALWAYS
FOLLOWING THESE SIMPLE RULES:
1) BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL
EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU.
2) STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM, PROPER STRETCHING WILL PREPARE YOUR
JOINTS AND MUSCLES FOR EXERCISE AND HELP AVOID INJURIES.
3) IF AT ANY TIME YOU SHOULD FEEL FAINT OR DIZZY, NAUSEOUS OR EXPERIENCE ANY OTHER
ABNORMAL SYMPTOMS OR DISCOMFORT, DISCONTINUE USE AND CONSULT YOUR DOCTOR.
4) DO NOT USE THIS EQUIPMENT WITHOUT QUALIFIED SUPERVISION AND PROPER TRAINING NEVER
WORK OUT ALONE ALWAYS HAVE A PARTNER.
5) SECURELY TIGHTEN ALL BOLTS AND REGULARLY CHECK TO ENSURE ALL BOLTS HAVE NOT
LOOSENED.
6) WEAR GOOD RUBBER SOLE SHOES ONLY DO NOT USE BARE FOOTED OR WITH SOCKS ONLY.
7) DO NOT WEAR LOOSE CLOTHES SUCH AS ROBES, GOWNS, PANTS, LONG SHIRTS OR JEWELRY WITCH
COULD BECOME ENTANGLED IN MOVING PARTS.
8) DO NOT STAND OR KNEEL ON SEAT ALWAYS SIT OR LAY SQUARELY CENTERED.
9) KEEP HEAD, LIMBS AND BODY PARTS CLEAR OF MOVING PARTS AND WEIGHT PLATES.
10) CHILDREN SHOULD NOT USE EXERCISE EQUIPMENT WITHOUT SUPERVISION BECAUSE OF
POSSIBILITY OF INJURY FROM IMPROPER USAGE. THIS EQUIPMENT IS INTENDED FOR HOME USE ONLY.
11) REPLACEMENT OR WORN OR DEFECTIVE PARTS MUST BE REPLACE WITH FACTORY AUTHORIZED
PARTS. IF OTHER THAN FACTORY AUTHORIZED PARTS OR ASSESSORS ARE USED ALL WARRANTIES
AND LIABILITIES BECOME VOID.
SAFETY NOTICE
1) SET THE SPOTTERS (9) TO THE DESIRED HEIGHT FOR A SAFE WORK OUT.
2) RAISE THE BAR AND ROTATE IT OUT UNTIL THE HOOK CLEARS THE PEGS.
3) DO EXERCISES AS DESIRED.
4) WHEN FINISHED WITH THE SET, ROTATE THE BAR BACK AND SET ON PEGS. MAKE
SURE THE BAR IS SECURE BEFORE LETTING GO.
5) IF YOU DO INLINCE PRESS EXERCISES, LIFT TOWARD THE BACK OF THE MACHINE OR
PUT AT LEAST 90 LBS. ON THE WEIGHT HOLDERS TO AVOID A POSSIBLE TIPPING
HAZARD.
6) WHEN DOING CHIN-UPS, LOWER THE WEIGHT BAR SO THE MACHINE IS NOT TOP
HEAVY.
USE INSTRUCTIONS