Deltech Fitness DF4900 User manual

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
DF4900
LINEAR BEARING
SMITH MACHINE
Assembly Manual

DF4900
BOX CONTENTS
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
A
LH UPRIGHT
QTY 1
B
RH UPRIGHT
QTY 1
D
RH REAR SUPPORT
QTY 1
C
LH REAR SUPPORT
QTY 1
E
LH FOOT
QTY 1
F
RH FOOT
QTY 1
G
CROSSMEMBER
QTY 1
H
TOP FRAME
QTY 1
WEIGHT PLATE HOLDER
QTY 4
I

M
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
DF4900
BOX CONTENTS
SMITH BAR
QTY 1
JGUIDE ROD
QTY 2
KWEIGHT SLEEVE
QTY 2
LH & RH SAFETY CATCH
QTY 1 EACH
L
SMITH BAR COLLARS
QTY 2
N
LH & RH GUIDE ROD COLLAR
QTY 1 EACH
O
RH COLLAR
WITH STOP PIN
LH COLLAR
WITHOUT STOP PIN

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
DF4900
HARDWARE
RUBBER SHOE
QTY 4 RUBBER SPACER QTY 4
P Q RUBBER DONUT
QTY 2
R
HOOK CATCH ROD
ASSEMBLY
QTY 22
S
M12 x 90MM BOLT
QTY 12
U
M12 LOCKNUT
QTY 20
M12 WASHER
QTY 40
CHROME SPRING
QTY 2
AA
M10 LOCKNUT
QTY 8
M10 WASHER
QTY 16
TWEIGHT SLEEVE
BOLT
QTY 2
M10 x 25MM BOLT
QTY 8
VW
XYZ
HEX WRENCH
QTY 2
BB CC
CORNER FLANGE
QTY 2
DD
MOUNTING FLANGE
QTY 4
EE
M12 x 70MM BOLT
QTY 8

(NOTE: THE NUTS USED ON
THIS PRODUCT ARE LOCK
NUTS, THIS MEANS YOU
MUST TIGHTEN THEM DOWN
PAST THE PLASTIC INSERT)
X
Z
E
C
VXP
G
Z
X
P
F
X
V
D
P
ASSEMBLE THE LH FOOT (E), RH FOOT (F), CROSS MEMBER (G), AND THE LEFT AND RIGHT REAR
SUPPORTS (C) AND (D), USING THE M12 x 90MM BOLTS (V), M12 WASHERS (X), AND M12 LOCK-
NUTS (Z). (LEAVE THE BOLTS HAND TIGHTENED AT THIS TIME)
SLIDE THE RUBBER SHOES (P) ONTO THE LH AND RH FEET (E) & (F).
TOOLS REQUIRED:
WRENCHES OR METRIC SOCKET SET
HEX WRENCHES (INCLUDED)
ASSEMBLY REQUIRES 2 PEOPLE
MAKE SURE GUIDE BAR RETAINERS
ARE TOWARDS THE OUTSIDE
P
FRAME ASSEMBLY

V
ASSEMBLE THE LH AND RH UPRIGHTS (A) & (B) TO THE LH AND RH FEET USING THE M12 x 90MM
BOLTS (V), M12 WASHERS (X), AND M12 LOCKNUTS (Z).
A
X
XZZX
XV
B
FRAME ASSEMBLY

V
ASSEMBLE THE REAR SUPPORTS TO THE UPRIGHTS USING THE M12 x 90MM BOLTS (V), M12
WASHERS (X), AND M12 LOCKNUTS (Z).
X
X
Z
FRAME ASSEMBLY

INSTALL HOOK CATCH RODS INTO UPRIGHTS USING BOLT, WASHER, AND LOCK WASHER.
SMITH BAR CATCH ROD ASSEMBLY
?
AA

INSTALL WEIGHT PLATE HOLDERS (I) USING M10 x 70MM BOLTS(R), M10 WASHERS (Y), FLANGE
(EE), AND M10 LOCKNUT (AA). SLIDE RUBBER SPACERS (Q) ONTO WEIGHT PLATE SUPPORTS.
REAR WEIGHT HOLDER ASSEMBLY
RYEE
IY
AA
Q

GUIDE ROD INSTALLATION
INSERT THE GUIDE RODS (K) INTO THE RETAINERS AT THE BOTTOM. SLIDE THE RUBBER DONUTS (S)
ONTO THE GUIDE RODS AND MOVE TO THE BOTTOM. INSTALL THE RH AND LH SAFETY CATCHES (O)
AND HOOK ONTO ONE OF THE CATCH PINS TO SUPPORT THE GUIDE RODS. SLIDE THE CHROME
SPRINGS (BB) ONTO THE GUIDE RODS (K).
O
BB
S
K
BB
O
S
K