Deltech Fitness DF930 User manual

700 LB WEIGHT CAPACITY
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
ASSEMBLY INSTRUCTIONS FOR
THE DF930 LAT. MACHINE
The DF908 consists of the DF906 Lat
Machine and the DF832 Pec Attachment

ASSEMBLY
INSTRUCTIONS
QTY 1
DF906
BOX CONTENTS
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
BACK SUPPORT
QTY 1
A
FRONT SUPPORT
QTY 1
B
BOTTOM FRAME
QTY 1
C
REVOLVING CHROME
ROW BAR
QTY 1
D
REVOLVING CHROME
LAT BAR
QTY 1
F
LAT CABLE
QTY 2
E

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
BOX CONTENTS
SEAT SUPPORT
QTY 1
J
SEAT BRACKET
QTY 1
I
UPPER PULLEY
FRAME
QTY 1
G
SEAT PAD
QTY 1
H
FOOT
QTY 1
N
HOLD-DOWN SUPPORT
QTY 1
M
HOLD-DOWN
TUBE
L
WEIGHT SLIDE
QTY 1
K
ROLLER PAD
QTY 2
P
LEG PAD TUBE
QTY 1
O
HARDWARE PACK
QTY 1
FLANGE
QTY 2
Q
BOTTOM PULLEY
FRAME
QTY 1
R

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
DF906
HARDWARE
2” SQUARE CAP
QTY 1
S
1-3/4” SQUARE
CAP
QTY 1
T U
MUSHROOM CAP
QTY 2
2” x 3” CAP
QTY 2
V
1-3/4” ROUND CAP
QTY 2
W
RUBBER SHOE
QTY 2
X
4-1/2” PULLEY
QTY 4
Y
3-1/2” PULLEY
QTY 3
AA
PULLEY BUSHING
QTY 6
BB
SNAP HOOK
QTY 5
CC

BOLT DIAMETER
M 10 M 12M 8
25 MM
MEASURE BOLT LENGTH HERE
30 MM
75 MM
65 MM
70MM
80MM
55MM
CHAIN
QTY 1
M10 x 67MM
CARRIAGE BOLT
QTY 9
HARDWARE
DD EE
M10 WASHER
QTY 25
I I
RUBBER
BUMPER
QTY 1
KK
REDUCER
QTY 2
LL
M10 x 76MM BOLT
QTY 5
FF
M10 x 43MM BOLT
QTY 4
JJ
M10 LOCKNUT
QTY 16
GG
HH
M10 x 25MM BOLT
QTY 6
OLYMPIC ADAPTER
QTY 2
MM

(SEE INSET) ASSEMBLE THE 4 ½” PULLEY (Y) INTO THE BOTTOM PULLEY FRAME
(R) USING THE M10 x 43 BOLT (GG), M10 WASHERS (II), AND M10 LOCKNUT (JJ).
INSTALL TO BOTTOM FRAME (C) USING THE M10 x 67MM CARRIAGE BOLTS (EE),
M10 WASHERS (II), AND M10 LOCKNUTS (JJ).
ATTACH THE FOOT (N) TO THE BOTTOM FRAME (C) USING THE M10 x 76MM
BOLTS (FF), M10 WASHERS (II), AND M10 LOCKNUTS (JJ). INSTALL THE RUBBER
BOOTS (X) OVER THE ENDS OF THE FOOT. NOW INSERT THE 2” SQ. PLASTIC CAP
(S) AND 1 ¾” ROUND CAPS (W) INTO THE BOTTOM FRAME (C).
BOTTOM FRAME ASSEMBLY
TOOLS REQUIRED:
METRIC WRENCHES OR SOCKET SET
Some components may be pre-installed
from the factory
(NOTE: THE NUTS USED ON THIS
BENCH ARE LOCK NUTS, THIS MEANS
YOU MUST TIGHTEN THEM DOWN
PAST THE PLASTIC INSERT.)
Y
GG I I
I I
R
JJ
FF
N
I I
I I
JJ
X
X
I I
I I
EE
JJ JJ
R
C
W
W
S

ATTACH THE SEAT PAD (H) TO THE SEAT BRACKET (I) USING THE M10 x 25MM
BOLTS (HH) AND THE M10 FLAT WASHERS (II). THEN SLIDE THE SEAT BRACKET
(I) INTO THE SEAT SUPPORT (J).
(WAIT TO COMPLETE THE FOLLOWING STEP UNTIL THE CABLES ARE INSTALLED)
INSTALL THE 4 ½” PULLEY (Y) INTO THE SEAT SUPPORT TUBE (J) USING THE
M10 x 43MM BOLT (GG) , M10 WASHERS (II), AND M10 LOCK NUT (JJ).
SEAT FRAME ASSEMBLY
H
I
HH
I I
J
Y
GG I I
I I
JJ

SLIDE THE HOLD-DOWN TUBE (L) INTO THE HOLD-DOWN SUPPORT (M)
NEXT SLIDE THE LEG PAD TUBE (O) INTO THE HOLD-DOWN TUBE (L).
THEN SLIDE THE ROLLER PADS (P) OVER THE LEG PAD TUBE (O) AND INSERT
THE PLASTIC CAPS (U). INSTALL THE 1¾” SQUARE CAP (T).
LEG HOLD DOWN ASSEMBLY

INSTALL THE REDUCERS (MM) INTO EACH END OF WEIGHT SLIDE (K). SCREW THE
RUBBER BUMPER (MM) INTO BOTTOM FLANGE.
A SPRAY LUBRICANT IS RECOMMENDED FOR THE INNER SURFACE OF THE REDUCERS
TO ENSURE SMOOTH MOVEMENT OF THE WEIGHT SLIDE.
NN
MM
NN
WEIGHT SLIDE ASSEMBLY

FLOATING PULLEYASSEMBLY
ASSEMBLE THE FLOATING PULLEY ASSEMBLY BY USING 4-1/2” PULLEYS (Y),
FLANGES (Q), M10 x 43 BOLTS (GG), M10 WASHERS (II), AND M10 LOCKNUTS (JJ).
I I
I I
JJ
Q
GG
Y