DEMA TITAN II Assembly instructions

ENTER
DEMA Engineering Company
Titan II Installation and
Programming Training

ENTER
Titan II
Premium Warewash Dispenser
•Unique auto switchover mode designed to
reduce service calls
Automatically switches to probeless
mode if the probe fails to function
•Can be set up in 3 different modes -
concentration, probeless or auto
switchover
•Optional items include
Magnetic field sensor
Low level / out of product alarm
•Available for 2 or 3 products
•Easy to add 3rd pump if necessary

ENTER
Titan II
Premium Warewash Dispenser
•Models include
Two product –liquid/liquid or
liquid/dry
Three product –all liquid or
liquid/liquid/dry
•100-260VAC 50/60Hz main power
(constant power)
•24-480VAC trigger signals
•DEMA solenoid for dry detergent
control
•Rinse pump output 0.5 oz./min
(16ml / min)
T.812.DL
T.813.DLL

ENTER
Wall Mounting
•Unpack the Titan
•Remove mounting plate
from Titan
•Attach mounting plate to
wall
•Install Titan on the
mounting plate
•Replace screw
Remove screw and slide
plate down

ENTER
Wall Mounting
•Follow instructions
on Mounting
Bracket

ENTER
Mounting Considerations
•Choose a location for Titan that’s
convenient for operation and chemical
locations
•Distance from electrical connections for
Titan
•Flat vertical surface away from splashing
and steam originating from machine
•Titan should be installed in an easily
observed and serviceable location

ENTER
Electrical Connection
•Connect main power and triggers to the dish
machine following manufacturers
recommendations
•Constant main power should be supplied at
100 -250VAC
•Connect detergent and rinse triggers to dish
machine
24 –480VAC

ENTER
Wiring Configuration
BROWN –Wash Trigger (HOT)
–Wash Trigger (RETURN)
BLACK –Rinse Trigger (HOT)
RED –Rinse Trigger (RETURN)
GREEN –Earth Ground
WHITE
DISH MACHINE ELECTRICAL CONNECTION POINT
WARNING: For safety purposes disconnect main power to
the dish machine. Connect power to the Titan per the dish
machine manufacturer’s recommendations.
UNIT MUST BE GROUNDED (EARTHED).

ENTER
Installation of Bulkhead Fitting
•Install detergent bulkhead fitting
to dish machine wash tank
•Install above the water line in the
tank
•Bulkhead fitting should be
directly above concentration
Probe
•Gasket should be installed
externally to the wash tank

ENTER
Detergent & Plumbing Connections
•Install Viking detergent bowl (see separate
instructions)
•From water supply run ¼” OD copper
tubing to inlet fitting of Titan detergent valve
•From outlet fitting of Titan detergent valve
run ¼” OD copper tubing to inlet of Viking
bowl vacuum breaker
•From outlet of Viking bowl run 9/16” ID
tubing to bulkhead fitting mounted on side
of wash tank

ENTER
Rinse & Sanitizer Connections
•Locate injection points on rinse
manifold of dish machine
•Install supplied check valve for
rinse and sanitizer
Stainless steel check valve for rinse
Kynar (plastic) check valve for sanitizer
•Cut the ¼” OD vinyl tubing to length
required to reach from the rinse
/sanitizer chemicals to the Titan
pumps
•Cut vinyl tubing to length required
to reach from Titan pumps and
rinse/sanitizer check valves

ENTER
Installation of Conductive Probe
•The Probe should be installed on
lower half of the wash tank
•The probe should be installed
directly below chemical injection
when possible
•Remove electrical ring
connectors from probe and crimp
conductors of probe cable
•Re-install ring connectors and
secure excess probe cable

ENTER
Typical Titan II Set Up

ENTER
Titan II Button Functions
LEFT arrow
moves cursor
to the left
DOWN arrow decreases value
or moves cursor down
RIGHT arrow
moves cursor
to the right
UP arrow
increases
value or
moves cursor
up
ENTER button
accepts values
entered

ENTER
Titan II Programming
•Separate sections for
auto switchover,
probeless, and
concentration mode

ENTER
Idle Screen
•Idle / Default screen shown
when unit is not being
programmed
•Press enter to advance to
priming and programming
functions
•Unit will return to this screen
during programming if long
delays are taken during
programming
•Idle screen message can be
changed in programming

ENTER
Language Screen
•Press ENTER to modify
language
•Use UP & DOWN arrows to
select between 4 languages
English, Spanish,
Portuguese and French
•Press ENTER to select
desired language
•Press DOWN arrow to
advance to other screens

ENTER
Detergent Prime
• 1st screen seen after
the language screen
•Press enter to start &
stop pump priming
OR
•Press DOWN arrow to
advance to other
screens

ENTER
Rinse Prime
•Press enter to start &
stop pump priming
OR
•Press DOWN arrow to
advance to other
screens

ENTER
Sanitizer Prime
•Press enter to start &
stop pump priming
OR
•Press DOWN arrow to
advance to other
screens