Digiplex DGP2-641AC User guide

LCD Keypad & Access Control LCD KeypadLCD Keypad & Access Control LCD Keypad
DGP2-641 / DGP2-641AC
System Manager’s ManualSystem Manager’s Manual
Also includes
Operating Instructions

User’s Manual 3
TABLE OF CONTENTS
INTRODUCTION ........................................................... 4
Legend.......................................................................................... 4
BASIC OPERATION ..................................................... 4
Auditory Feedback (Beep Tones) ................................................ 4
Confidential Mode ....................................................................... 5
Partitioned System ....................................................................... 5
Area Status Display...................................................................... 5
ARMING ........................................................................ 5
Exit Delay Timer.......................................................................... 5
Regular Arming............................................................................ 5
Stay Arming................................................................................. 6
Instant Arming ............................................................................. 6
Force Arming............................................................................... 6
Bypass Programming................................................................... 6
One-Touch Buttons...................................................................... 7
Keyswitch Arming ....................................................................... 7
Auto-Arming................................................................................ 7
DISARMING .................................................................. 7
Entry Delay Timer........................................................................ 7
Disarming an Armed System....................................................... 8
Alarm Memory Display ............................................................... 8
ACCESS CODES .......................................................... 8
System Master Code (Default 123456)........................................ 8
Deleting User Access Codes........................................................ 8
Programming User Access Codes................................................ 9
User Options............................................................................... 11
Access Control User Options..................................................... 11
USING ACCESS CONTROL....................................... 12
Entering & Exiting..................................................................... 12
Arming and Disarming with Card.............................................. 12
How Access Control Works....................................................... 13
TROUBLE DISPLAY................................................... 14
Event Record Display ................................................................ 14
ADDITIONAL FEATURES........................................... 15
Programmable Outputs (PGMs)................................................. 15
Keypad Settings ......................................................................... 15
Set Time & Date......................................................................... 15
Programming Chime Zones ....................................................... 16
Panic Alarms.............................................................................. 16
Quick Function Buttons ............................................................. 16
TESTING AND MAINTENANCE................................. 16
Burglar Alarm Testing ............................................................... 16
Fire Alarm Testing..................................................................... 16
System Maintenance .................................................................. 17
System Test................................................................................ 17
FIRE AND BURGLAR ALARMS................................. 17
Standard Fire Zone..................................................................... 17
Delayed Fire Zone...................................................................... 17
Fire Safety Tips.......................................................................... 18
Minimizing Home Fire Hazards................................................. 18
Home Fire Warning System....................................................... 18
Burglar Alarm............................................................................. 18
VOICE-ASSISTED ARM/DISARM MODULE
INTRODUCTION ......................................................... 19
ACCESS CODES........................................................ 19
HOW DO I USE IT?..................................................... 19
THINGS YOU SHOULD KNOW.................................. 19
When Accessing your InTouch.................................................. 19
When Arming or Disarming....................................................... 19
When Activating or Deactivating a PGM... ............................... 19
When Using your Intouch... ....................................................... 20
TELEPHONE BUTTON FEATURES........................... 20
INTOUCH EXAMPLE.................................................. 20
INTOUCH SYSTEM CHECKLIST............................... 21
INDEX.......................................................................... 23

4 User’s Manual
1.0 INTRODUCTION
Your Digiplex Security System is an advanced technology security system that will provide you with reliable security
protection and powerful features that are easy to use. The elegant and user-friendly LCD keypad will allow you easy
access to your security system's functions and information at the touch of a button. The 32-character LCD screen
will display messages and menus to guide you through the system’s operations. Your Installer can even customize
the messages for your home or business.
Since you will communicate your instructions to your system through the keypad, please read this manual carefully
and have your Installer explain basic system operation.
If you have the InTouch Voice Assisted Arm/Disarm Module (APR3-ADM2) connected to your Digiplex security
system, please refer to page 19 for operating instructions.
1.1 LEGEND
Indicates a warning or an important note.
Indicates useful information or a tip.
[SQUAREBRACKETS]Indicates information that must be entered on the keypad.
2.0 BASIC OPERATION
The following sections will introduce you to the roles of the buttons, lights, and messages on your LCD keypad.
Figure 2.1: Basic Overview
2.1 AUDITORY FEEDBACK (BEEP TONES)
When you enter information on the keypad, the keypad will guide you with beep tones to communicate the
acceptance or rejection of your entries.
Confirmation Beep: When an operation (i.e. arming/disarming) is successfully entered or when the system
switches to a new status/mode, the keypad emits an intermittent beep tone (“BEEP-BEEP-BEEP-BEEP-BEEP”).
Rejection Beep: When the system reverts to a previous status, or when an operation is incorrectly entered, the
keypad emits a continuous beep tone (“BEEEEEEEEEEP”).
The LCD screen will guide you
with detailed messages.
Use the arrow buttons to scroll
through the current menu when
the arrows appear in the LCD
screen.
ACTION BUTTONS:
Each button’s function is explained in the following sections of the manual.
“STATUS” LIGHT:
When Green:
ON = All zones are closed.
OFF = One or more zones are open.
FLASH = Exit Delay
When Red:
ON = Area(s) armed
OFF = Area(s) disarmed
FLASH = System in Alarm
“AC” LIGHT:
ON = AC power
OFF = Power failure
[CLEAR]= Erases current data entry
or reverts to the preceding step. [ENTER]= Saves current data and
exits current menu.

LCD Keypad 5
2.2 CONFIDENTIAL MODE
Your Installer can program keypads to not display the status of your system automatically by changing the LCD
screen to Confidential Mode. In Confidential Mode:
•The zones and status messages will NOT be displayed
•The indicator lights will NOT illuminate
•Depending on how your keypad was programmed by your installer, you must either press a button or enter your User
Access Code to illuminate the indicator lights and activate Normal Mode.
2.3 PARTITIONED SYSTEM
A separated system is called a Partitioned System, which can be useful in situations where shared security systems
are more practical. Your installer can design your system to recognize up to four separate protected areas. For
example, a company that has both an office area and a warehouse area can arm and disarm each area separately
and control the access to each area.
If you have access to more than one area, and you need to select a specific area(s) when prompted by your LCD
keypad, follow either one of the following three methods to make your selection:
•Press the keypad button corresponding to the area you wish to select (i.e. 1, 2,...4).
•Press the [0] button for all areas.
•Use the [pp] and [qq]buttons, and press [ENTER]when the area you want to select appears on the screen.
2.4 AREA STATUS DISPLAY
In Area Status Display mode, the following information will scroll on the LCD screen:
•“ready”: if all zones in the selected area are closed.
•“not ready”: if zones in the selected area are open.
•open zones within that area (i.e. “Front Door Open”).
•“Trouble(s)”: (section 7.0 on page 14) if a trouble has occurred.
•“Alarms in Memory”: (section 4.3 on page 8) if an alarm has occurred.
•“Armed” ; “Force Armed” ; “Instant Armed” ; “Stay Armed”: displays the arming status of the selected area.
3.0 ARMING
When your system is armed, it can respond to any breach in the protected zones by causing an alarm and sending
a report to your Central Monitoring Station.
3.1 EXIT DELAY TIMER
When you arm your system, it will trigger the Exit Delay Timer to provide you with enough time to exit the protected
area before the system is armed.
3.2 REGULAR ARMING
The Area Status Display
allows you to view the status
of the selected areas in a
Partitioned System (Refer to
section 2.3 on page 5).
How do I see the status of the areas?
1) Enter your [ACCESS CODE], then press the [1] button.
2) Press the button corresponding to the area (i.e. 1, 2,...4), or use the [pp] and
[qq]buttons and press [ENTER]when the area you want to view appears on
the screen.
3) Press [CLEAR]to exit.
This method is used for the
everyday arming of your
system. All zones within the
protected area must be
closed to Regular arm the
system.
How do I Regular arm the system?
1) Enter your [ACCESS CODE].
2) Press the [ARM]button.
3) If you have access to more than one area, select the area(s) you wish to
Regular arm (refer to section 2.3 on page 5).

6 User’s Manual
3.3 STAY ARMING
3.4 INSTANT ARMING
3.5 FORCE ARMING
3.6 BYPASS PROGRAMMING
In order to bypass a zone, the following conditions must be met:
- The zone must have the Bypass option programmed by the installer.
- Your User Access Code must be programmed to enable the Bypass option.
- Your User Access Code must have access to the zone’s Area Assignment.
Fire Zones cannot be bypassed.
3.6.1 BYPASS RECALL
Stay arming will partially arm
your system to permit you to
remain in your home or office
by arming the outer zones
(perimeter) of the protected
area (i.e. doors and
windows).
How do I Stay arm?
1) Enter your [ACCESS CODE].
2) Press the [STAY]button.
3) If you have access to more than one area, select the area(s) you wish to
Stay arm (refer to section 2.3 on page 5).
This feature is the same as
Stay arming except that there
is no Entry Delay. Therefore,
any armed zone that is
breached will immediately
generate an alarm.
How do I Instant arm?
1) Enter your [ACCESS CODE].
2) Press the [5] button.
3) If you have access to more than one area, select the area(s) you wish to
Instant arm (refer to section 2.3 on page 5).
Force arming allows you to
quickly arm your system
when zones are open.
However, once the open zone
is closed, your system will
then arm that zone as well.
How do I Force arm?
1) Enter your [ACCESS CODE].
2) Press the [FORCE]button.
3) If you have access to more than one area, select the area(s) you wish to
Force arm (refer to section 2.3 on page 5).
You can bypass certain zones
when you arm the protected
area(s). When a zone is
bypassed, it will be ignored
the next time your system is
armed. Once your area is
disarmed, the system will
unbypass the zone.
How do I Bypass a zone?
1) Enter your [ACCESS CODE].
2) Press the [BYP]button.
3) Enter the zone number (i.e. 01, 02,...48), or use the [pp]and [qq]buttons and
press [BYP] once the zone you want to bypass appears on the screen. If
“bypassed” does not appear on the screen and the keypad emits a Rejection
Beep, you may not have access to bypass that zone.
4) Repeat step 3 until all zones you want to bypass have been selected.
5) Press the [ENTER]button to save and exit.
Bypass Recall reinstates the
zones that were bypassed the
last time your system was
armed.
How do I activate Bypass Recall?
1) Enter your [ACCESS CODE].
2) Press the [BYP] button.
3) Press the [MEM]button.
Zones bypassed the last time your system was armed are bypassed.
4) Press the [ENTER]button to save and exit.

LCD Keypad 7
3.7 ONE-TOUCH BUTTONS
If enabled by your Installer, you can access the following features without using your User Access Code by pressing
and holding the desired One-Touch button.
3.8 KEYSWITCH ARMING
A key can be used to arm and disarm your system using two forms of keyswitches. With a Maintained Keyswitch,
place the key in the “ON” position to arm your system, and place the key in the “OFF” position to disarm your
system. With a Momentary Keyswitch, place the key in the “ON” position briefly then place it back in the “OFF”
position to arm the system. Repeat this process to disarm with a Momentary Keyswitch.
3.9 AUTO-ARMING
If enabled by your Installer, you can set the time that an area will arm itself automatically.
3.9.1 TIMEDAUTO-ARMING
3.9.2 NOMOVEMENTAUTO-ARMING
Your system can be programmed to send a report to your Central Monitoring Station and/or arm the system if there
is no activity in the area during a specified period of time. Your installer can set No Movement Auto-Arming to
function in either Regular or Stay arming mode.
4.0 DISARMING
When your system is disarmed, it deactivates any alarms in progress, and it deactivates the zones so the alarm will
not be triggered if zones are breached.
4.1 ENTRY DELAY TIMER
Your installer will program designated entry points (i.e. the front door) with an Entry Delay Timer. This delay gives
you time to enter the armed premises and enter your code to disarm your system before the alarm is triggered.
BUTTON FEATURE BUTTON FEATURE
[ARM]Regular arm [DISARM]Disarm a Stay/Instant armed area
[STAY]Stay arm [5] Instant arm
[FORCE]Force arm [6] Change display settings
[BYP]Bypass Programming [7] View Event Record display
Your installer can set Timed
Auto-Arming to function in
either Force or Stay arming
mode. A sixty-second Exit
Delay sequence will begin
prior to your system
automatically arming itself at
the programmed time.
How do I set the Auto-Arming timer?
1) Enter your [ACCESS CODE].
2) Press the [0] button.
3) Press the [MEM]button.
4) If you have access to more than one area, press the area’s number, or use
the [pp]and [qq]buttons and press the [ACC]button when the area you want
to program appears on the screen.
5) Enter the time you want the area to be armed according to the 24-hour clock
(i.e. 9 a.m. is 09:00 and 9 p.m. is 21:00).
6) Press the [ENTER]button to save and exit.

8 User’s Manual
4.2 DISARMING AN ARMED SYSTEM
In the case of a burglar alarm, leave the premises and call the Police from a safe place.
4.3 ALARM MEMORY DISPLAY
5.0 ACCESS CODES
Access Codes allow access to the system. Your system supports up to 96 User Access Codes. Codes are given a
User Number between 002 and 096 (User Number 001 is the System Master Code). Your Installer will program
User Access Codes to be four, six, or variables of one to six digits in length. Each digit can be any value between
zero and nine. If your Installer programmed your system to accept a variable code length, you have to press the
[ENTER]button after entering your User Access Code.
5.1 SYSTEM MASTER CODE (Default 123456)
The System Master Code will
give you access to all the
features available on your
system, as well as the ability
to add, modify, or delete any
User Access Codes. We
suggest that you change this
code to prevent others from
accessing and changing
options without authorization. Your Installer can set The System Master Code to be either 4 or 6 digits in length.
The System Master Code has access to all Access Control Doors and all Access Control
features at all times. Only the card’s serial number and the choice of arming method can be
changed. If the other options are manually changed, the System Master Code will immediately
revert to its original programming.
5.2 DELETING USER ACCESS CODES
To delete User Access Codes, follow steps 1 to 5 in Figure 5.1 on page 9, but press the [CLEAR]button in Step 5, 6
and 7. Once the information is erased, press the [ENTER]button to save and exit.
You can only disarm an area
to which your User Access
Code is assigned. User
Access Codes with the “Arm
Only” (section 5.4 on page
11) option enabled cannot
disarm an armed system.
How do I disarm the system?
1) Enter your [ACCESS CODE].
2) Press the [DISARM]button.
If you have access to more than one area, select the area(s) you wish to
disarm (refer to section 2.3 on page 5).
How do I disarm a system in alarm?
1) Enter your [ACCESS CODE].
2) In the case of a false alarm, call your Central Monitoring Station quickly to
advise them of the false alarm.
Your system will record all the
alarms that occurred during
the last armed period. The
zones in alarm will remain in
the Alarm Memory until the
next time that area is armed.
How do I view the list of alarms that occurred?
When an alarm has occurred, the LCD screen will display “Alarms in Memory
[MEM] to View”.
1) Press the [MEM]button. Each zone that was breached while armed will
appear below “Alarm in:”.
2) Press the [CLEAR]button to exit the Alarm Memory Display.
How do I change the System Master Code?
1) Enter the current [SYSTEMMASTERCODE](default: 123456).
2) Press the [0] button.
3) Press the [ACC]button.
4) Enter the number [001].
5) Enter a [NEWCODE].
6) Press the [ENTER]button to save and exit.

LCD Keypad 9
5.3 PROGRAMMING USER ACCESS CODES
The System Master and Users with the Master feature can program User Access Codes with User Options and
Area Assignments. Figure 5.1 on page 9 describes the steps you would follow to program User Access Codes.
If the keypad emits a Rejection Beep at any point during the programming procedure, you may have chosen an
existing User Code or you do not have access to certain User Options (section 5.4) and Area Assignments (step 7
in Figure 5.1 on page 9). User’s with the Master feature can only assign User Options and Area Assignments that
they are assigned to. For example, if a User with the Master feature is assigned User Option 1 and Area 2, they can
only assign Options 1 and Area 2 to a User Access Code.
Figure 5.1: Programming User Access Codes
Enter your [ACCESS CODE](System Master Code or User Access Code with Master
feature).
Press [0] to enter the Programming Menu.
From Programming Menu, press [ACC].
Enter the 3-digit User Number you want to program; press the [qq]button to scroll the
list of codes then press [ACC]once the desired code appears on the screen.
Enter a User Code within the brackets. Press the [pp]button to reach the User Options
screen.
NOTE: The User Code is a Personal Identification Number (P.I.N.).
Program the User Options by pressing the number on your keypad corresponding to the
User Option you wish to enable. The option is considered ON when the number
appears within the brackets. Proceed to step 7 by pressing the [pp]button. For a
detailed description of the User Options refer to section 5.4 on page 11.
Options [1] and [2] : Master Feature
[1] OFF = Master Feature disabled.
[1] ON, [2] OFF = User can only modify User
Access Codes.
[1] ON, [2] ON = User has full Master rights.
User can create, modify, and program User
options, User Access Options and Area
Assignments.
Option [3] : Duress
Option [4] : Bypass
Option [5] : Arm Only
Option [6] : Stay and Instant Arm
Option [7] : Force Arm
Option [8] : Area Access

10 User’s Manual
Users are able to perform actions (arming, disarming, etc.) only in the area(s) they are
assigned. To assign an area(s) to a User Access Code, enter the number
corresponding to the area you wish to assign (i.e. [1] = area 1, ...[4] = area 4).
Press the [qq]button to return to the User Options; press the [pp]button to proceed to
step 8; or press the [ENTER]button to save and exit programming mode.
NOTE: If no area is assigned, and if PGMs are programmed by your Installer, the User
can only control the PGMs. Refer to section 8.1 on page 15 for a more detailed
explanation of PGMs.
A) Enter the 2-digit Access Level (i.e. 00, 01,...15) within the first set of brackets.
An Access Level determines which Access Control Doors a User is allowed to pass
through. There are 16 possible Access Levels which are usually programmed by your
Installer. Access to all Access Control Doors is Access Level 00.
B) Enter the 2-digit Schedule (i.e. 00, 01,...15) in the second set of brackets.
Schedules, programmed by your Installer, determine the hours, days, and holidays that
Users are permitted through Access Control Doors. Each user is assigned a Schedule
through the User Access Code. To provide access at all times, assign Schedule 00.
Program the Access Control User Options by pressing the number on your keypad that
corresponds to the Option you wish to assign. The option is considered ON when the
number appears within the brackets. For a detailed description of the User Access
Control Options, refer to section 5.5 on page 11. Press the [pp]button to proceed to
step 10.
Option [1] : Access Card is Activated
Option [2] : Can Disarm with Access Card
Option [3] : Extended Unlocked Period
Options [4], [5], [6] & [7] : Arming with Card
Option [4] OFF = Disable the Arming with Card feature
Option [4] ON, options [5], [6] & [7] OFF = Regular Arm
Options [4] & [5] ON, options [6] & [7] OFF = Stay Arm
Options [4] & [6] ON, options [5] & [7] OFF = Instant Arm
Options [4] & [7] ON, options [5] & [6] OFF = Force Arm
Option [8] : Access to Armed Access Control Doors
Enter the Access Control Card’s serial number within the brackets on the screen by
either using the keypad buttons, or presenting the card to the keypad’s reader.
Press the [ENTER]button to save and exit.