Digital Projection M-Vision 930 3D Series User manual

Rev C February 2015
M-Vision 930 3D Series
High Brightness Digital Video Projector
4INSTALLATION AND QUICK-START GUIDE
4CONNECTION GUIDE
4OPERATING GUIDE
4REFERENCE GUIDE
115-072C

page i
Digital Projection M-Vision 930 Series
Rev C February 2015
About This Document
Follow the instructions in this manual carefully to ensure safe and long-lasting use of the projector.
Symbols used in this manual
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless
the instructions are closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely
followed.
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features
without prior notice.
Legal notice
Trademarks and trade names mentioned in this document remain the property of their respective owners.
Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.
Copyright © 2015 Digital Projection Ltd. All rights reserved.
Notes

page ii
Digital Projection M-Vision 930 Series
Rev C February 2015
Introduction
Congratulations on your purchase of this Digital Projection product.
Your projector has the following key features:
• Support for most 3D formats.
• HDBaseT® for transmission of uncompressed High Denition Video up to 100 m from the source.
• Edge Blend.
• Blanking control for custom input window sizing.
• Cornerstone, Vertical & Horizontal Keystone, Pincushion & Barrel, and Image Rotation.
• Control via LAN and RS232.
• Motorised lens mount.
A serial number is located on the product label. Record it here:
Notes

page iii
Digital Projection M-Vision 930 Series
Rev C February 2015
CONTENTS
INSTALLATION AND QUICK-START GUIDE ..............................1
WHAT’S IN THE BOX? ................................................................... 3
CONNECTING THE POWER SUPPLY ............................................. 4
PROJECTOR OVERVIEW ............................................................... 5
Front and rear views ............................................................................. 5
Control panel indicators ........................................................................ 6
REMOTE CONTROL....................................................................... 7
Infrared reception.................................................................................. 9
Remote control troubleshooting .......................................................... 10
POSITIONING THE SCREEN AND PROJECTOR........................... 11
CHANGING THE LENS................................................................. 12
Inserting a new lens ............................................................................ 12
Removing the lens .............................................................................. 13
CHANGING THE FILTERS ............................................................ 14
CHANGING THE LAMPS .............................................................. 16
OPERATING THE PROJECTOR.................................................... 18
Switching the projector on................................................................... 18
Switching the projector off................................................................... 18
Selecting an input signal or test pattern.............................................. 19
Input signal ........................................................................................ 19
Test pattern ........................................................................................ 19
Adjusting the lens................................................................................ 20
Adjusting the image............................................................................. 21
Orientation ......................................................................................... 21
Keystone ........................................................................................... 21
Picture .............................................................................................. 21
CONNECTION GUIDE ............................................................................23
SIGNAL INPUTS .......................................................................... 25
Digital inputs and outputs.................................................................... 25
Analog inputs ...................................................................................... 26
EDID on the DVI and VGA inputs........................................................ 27
Using HDMI/DVI switchers with the projector ..................................... 27
3D connections ................................................................................... 28
3D sources up to 60Hz requiring frame doubling and left/right interleaving.......... 28
Frame sequential 3D sources up to 120Hz ................................................. 28
Dual Pipe 3D ...................................................................................... 28
3D Sync............................................................................................... 29
3D Sync in ......................................................................................... 29
3D Sync out ....................................................................................... 29
CONTROL CONNECTIONS........................................................... 30
LAN connection examples .................................................................. 31
RS232 connection example ................................................................ 32

page iv
Digital Projection M-Vision 930 Series
Rev C February 2015
OPERATING GUIDE ................................................................................33
USING THE MENUS ..................................................................... 35
Opening the OSD................................................................................ 35
Opening a menu.................................................................................. 35
Exiting menus and closing the OSD.................................................... 35
Inside a menu...................................................................................... 36
Accessing sub-menus........................................................................... 36
Executing commands............................................................................ 36
Editing projector settings..................................................................... 37
Choosing a value from a list ................................................................... 37
Changing the value without viewing the list................................................. 37
Using a slider to set a value.................................................................... 37
USING THE PROJECTOR............................................................. 38
Main menu .......................................................................................... 38
Lens menu .......................................................................................... 39
Lens Control....................................................................................... 39
Lens Center ....................................................................................... 39
Image menu ........................................................................................ 40
Picture Mode ...................................................................................... 40
Brightness and Contrast ........................................................................ 40
Gamma............................................................................................. 41
Dynamic Black .................................................................................... 41
Adaptive Contrast ................................................................................ 41
Saturation, Hue, Sharpness and Noise Reduction ........................................ 41
Position and Phase .............................................................................. 42
Resync ............................................................................................. 42
Color menu.......................................................................................... 43
Color Space ....................................................................................... 43
Color Temperature ............................................................................... 44
Gamut .............................................................................................. 45
RGB Lift and Gain................................................................................ 45
Geometry menu .................................................................................. 46
Aspect Ratio....................................................................................... 46
Overscan........................................................................................... 47
Keystone ........................................................................................... 48
Rotation ............................................................................................ 50
Pincushion / Barrel............................................................................... 51
Corners............................................................................................. 52
Reset................................................................................................ 53
Blanking ............................................................................................ 54
Edge Blend menu................................................................................ 55
Blend Width........................................................................................ 56
Black Level Uplift ................................................................................. 57
Possible Geometry and Edge Blend combinations............................. 58
3D menu.............................................................................................. 59
3D types............................................................................................ 60
Some 3D settings explained ................................................................... 61
Frame rate multiplication in 3D images ...................................................... 62
Lamps menu ....................................................................................... 63
Setup menu......................................................................................... 64
Network ............................................................................................ 65
On Screen Display ............................................................................... 66
Presets ............................................................................................. 67
CONTENTS (continued)

page v
Digital Projection M-Vision 930 Series
Rev C February 2015
Information menu ................................................................................ 68
Factory Reset ..................................................................................... 68
REFERENCE GUIDE................................................................................69
THE DMD™.................................................................................. 72
CHOOSING A LENS ..................................................................... 74
Basic calculation ................................................................................. 75
Basic calculation example................................................................... 76
Full lens calculation............................................................................. 77
Introducing TRC .................................................................................. 77
Calculating TRC .................................................................................. 78
Calculating the throw ratio with TRC ......................................................... 79
Full lens calculation example .............................................................. 80
SCREEN REQUIREMENTS........................................................... 81
Fitting the image to the DMD™........................................................... 81
WUXGA images displayed full width ......................................................... 81
WUXGA images displayed with a height of 1080 pixels.................................. 82
WUXGA images displayed full height ........................................................ 83
Diagonal screen sizes......................................................................... 84
Fitting the image to the screen............................................................ 85
Positioning the screen and projector................................................... 86
POSITIONING THE IMAGE........................................................... 87
Maximum offset range......................................................................... 89
ASPECT RATIOS EXPLAINED...................................................... 90
Aspect ratio examples......................................................................... 91
FRAME RATES AND PULLDOWNS EXPLAINED........................... 93
Interlaced and progressive scan ......................................................... 93
Frame rates of image sources ............................................................ 93
Pulldowns - conversion into destination formats................................. 94
2:3 (normal) pulldown ........................................................................... 94
2:3:3:2 (advanced) pulldown................................................................... 95
APPENDIX A: LENS PART NUMBERS.......................................... 96
APPENDIX B: LENS CHARTS ...................................................... 97
How to use the lens charts ..................................................................... 97
TRC values applied in the charts ............................................................. 98
Full DMD™ width images....................................................................... 99
1.25:1 images ................................................................................... 100
1.33:1 images ................................................................................... 101
APPENDIX C: SUPPORTED SIGNAL INPUT MODES .................. 102
2D input modes................................................................................. 102
3D input modes................................................................................. 104
APPENDIX D: MENU MAP.......................................................... 105
CONTENTS (continued)

page vi
Digital Projection M-Vision 930 Series
Rev C February 2015
APPENDIX E: WIRING DETAILS..................................................111
Signal inputs and outputs...................................................................111
VGA ................................................................................................111
HDMI 1 and 2 ................................................................................... 112
DVI ................................................................................................ 113
Component 2.................................................................................... 114
Control connections .......................................................................... 115
LAN ............................................................................................... 115
RS232 ............................................................................................ 115
Trigger 1 & Trigger 2 ........................................................................... 116
IR input ........................................................................................... 116
3.5 mm mini jack ............................................................................... 116
USB ............................................................................................... 116
3D Sync IN and 3D Sync OUT .............................................................. 116
APPENDIX F: GLOSSARY OF TERMS.........................................117
TECHNICAL SPECIFICATIONS .................................................. 128
Models............................................................................................... 128
Inputs and outputs............................................................................. 129
Bandwidth ......................................................................................... 129
Remote control and keypad .............................................................. 129
Automation control ............................................................................ 129
Color temperature ............................................................................. 129
Lenses............................................................................................... 130
Lens mount ....................................................................................... 130
Mechanical mounting ........................................................................ 130
Orientation......................................................................................... 130
Electrical and physical specications................................................ 131
Safety & EMC regulations................................................................. 131
CONTENTS (continued)

Digital Projection M-Vision 930 Series
This page is intentionally left blank.

Rev C February 2015
M-Vision 930 Series
High Brightness Digital Video Projector
INSTALLATION AND QUICK-START GUIDE
4

Digital Projection M-Vision 930 Series
Installation and Quick-Start Guide
IN THIS GUIDE
Rev C February 2015
IN THIS GUIDE
What’s In The Box?............................................................................................. 3
Connecting The Power Supply........................................................................ 4
Projector Overview............................................................................................. 5
Front and rear views ...................................................................................................5
Control panel indicators.............................................................................................6
Remote Control.................................................................................................... 7
Infrared reception........................................................................................................9
Remote control troubleshooting .............................................................................10
Positioning The Screen And Projector....................................................... 11
Changing The Lens........................................................................................... 12
Inserting a new lens..................................................................................................12
Removing the lens ....................................................................................................13
Changing The Filters........................................................................................ 14
Changing The Lamps ....................................................................................... 16
Operating The Projector................................................................................. 18
Switching the projector on.......................................................................................18
Switching the projector off.......................................................................................18
Selecting an input signal or test pattern.................................................................19
Input signal......................................................................................................................19
Test pattern .....................................................................................................................19
Adjusting the lens .....................................................................................................20
Adjusting the image..................................................................................................21
Orientation ......................................................................................................................21
Keystone .........................................................................................................................21
Picture.............................................................................................................................21

page 3
Digital Projection M-Vision 930 Series
Installation and Quick-Start Guide
WHAT’S IN THE BOX?
Rev C February 2015
What’s In The Box? Notes
Make sure your box contains
everything listed. If any pieces are
missing, contact your dealer.
You should save the original box
and packing materials, in case you
ever need to ship your projector.
The projector is shipped without a
lens.
Only one power cable - dependent
on the destination territory - will be
supplied with the projector.
Remote control
(115-758)
2x AA batteries
User Manual on disc
(115-759)
Important Information (115-073)
Power cable, Europe
(112-001)
Power cable, North America
(112-002)
Projector (114-259)
Power cable, United Kingdom
(112-000)
2
PIC
MUTE
4
B
SHARP
O-SCAN NR
GAMMA
C-TEMP TEST
LENS
3D
SWAP
3D
FORMAT
2D/3D
ENTER
SOURCE
3
5
1
ASPECT
RATIO
MENU
USER MEMORY
C
A
|
ON POWER OFF
HDMI cable

page 4
Digital Projection M-Vision 930 Series
Installation and Quick-Start Guide
CONNECTING THE POWER SUPPLY
Rev C February 2015
Connecting The Power Supply
1. Make sure the voltage switch is
set to the correct voltage.
2. Make sure the mains power
button is in the OFF position.
3. Lift the cable lock up, push the
mains connector in rmly and push
the lock down to secure the cable.
4. Switch the mains power button
ON.
Notes
Use only the power cable
provided.
Ensure that the power outlet
includes a ground connection as
this equipment MUST be earthed.
Handle the power cable carefully
and avoid sharp bends. Do not
use a damaged power cable.
31 2
1Voltage switch
2Mains power button
3AC mains inlet with cable lock

page 5
Digital Projection M-Vision 930 Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev C February 2015
Projector Overview
Front and rear views
1Air inlet
2Lens
3Front infrared window
4Air inlet
5Connection panel
6Control panel
7Rear infrared window
8Lamp enclosures with air outlets
9Mains inlet with power button and voltage switch
10 Air outlet
11 Adjustable feet
12 Air inlet
Notes
Front view
2
3
1
11
4
Rear view
8
7
6
5
9
12
10

page 6
Digital Projection M-Vision 930 Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev C February 2015
Control panel indicators
During power on, all LED indicators become lit while the projector is
running a self test.
At the end of the self test only the STANDBY indicator remains lit.
When the projector goes from STANDBY to ON mode, the STANDBY
indicator is switched off and the ON indicator is lit.
The ON indicator ashes during cool down.
Indicators
1ON
2ERROR
3STANDBY
Error codes
If the projector detects an error, the red ERROR indicator will ash as shown in the chart below.
For example, if the lamp door is left open, the ERROR indicator will ash twice followed by a pause, then the sequence will repeat until the
error condition is corrected.
Condition ERROR indicator behavior
Lamp fail Flashes once, then pauses, then repeats.
Lamp door open Flashes twice, then pauses, then repeats.
Fan failure Flashes three times, then pauses, then repeats.
Over temperature Flashes four times, then pauses, then repeats.
Filter failure Flashes ve times, then pauses, then repeats.
System error On.
ENTER
ON ERROR LED STATUS STANDBY
MENU STBY
INPUT
1 32
Notes
During startup all LEDs light up
at the same time to indicate the
projector is carrying out a self-test.
delay
delay
delay
delay
delay

page 7
Digital Projection M-Vision 930 Series
Installation and Quick-Start Guide
REMOTE CONTROL
Rev C February 2015
Remote Control
1Power ON / OFF
2Transmit Indicator
Flashes when a button is pressed.
2Input selection
Select input source.
3Navigation
Navigate through the menus with the arrows, conrm your choice with ENTER.
4MENU
Access the projector OSD (on-screen display).
5User Memory
Load preset A, B or C.
6CONTRAST
Bring up the Contrast control, then adjust the value with the LEFT and RIGHT
arrow buttons..
7GAMMA
Switch to the next Gamma value:
...1.0, 1.8, 2.0, 2.2, 2.35, 2.5...
8LENS
Adjust lens position, zoom and focus.
92D/3D
Switch between 2D and 3D mode.
10 PIC MUTE
Close and open the shutter.
11 ASPECT RATIO
Switch to the next aspect ratio:
...16:9, TheaterScope, 4:3, 4:3 Narrow, 16:10, 5:4, Source...
continues on next page...
Notes
Input selection buttons:
• 1- HDMI 1
• 2- HDMI 2
• 3- DVI
• 4- HDBaseT
• 5 - VGA
You can create and later recall up
to four presets using the OSD. For
further information, see Presets in
the Operating Guide.
Presets can also be recalled through
protocol. For further information, see
the Protocol Guide.
Remote control
2
PIC
MUTE
4
B
SHARP
O-SCAN NRGAMMA
C-TEMP TESTLENS
3D
SWAP
3D
FORMAT
2D/3D
ENTER
SOURCE
3
5
1
ASPECT
RATIO
MENU
USER MEMORY
CA
|
ON POWER OFF
1
3
5
6
8
10
11
4
12
7
9
2

page 8
Digital Projection M-Vision 930 Series
Installation and Quick-Start Guide
REMOTE CONTROL
Rev C February 2015
Remote control - continued from previous page
13 BRIGHTNESS
Bring up the Brightness control, then adjust the value with the LEFT and
RIGHT arrow buttons.
14 O-SCAN
Switch to Overscan mode:
...Off, Crop, Zoom...
15 C-TEMP
Switch to the next color temperature:
...5400K, 6500K, 7500K, 9300K, Native...
16 3D SWAP
Switch 3D source dominance from left to right eye (left eye signal rst) and vice
versa.
17 SHARP
Bring up the Sharpness control, then adjust the value with the LEFT and
RIGHT arrow buttons.
18 NR
Bring up the Noise Reduction control, then adjust the value with the LEFT and
RIGHT arrow buttons.
19 TEST
Show a test pattern. Press again to show the next test pattern:
...Off, White, Black, Red, Green, Blue, CheckerBoard, CrossHatch, V Burst,
H Burst, ColorBar...
20 3D FORMAT
Switch between 3D formats as follows:
...Off, Auto, Side-by-Side, Top-and-Bottom, Dual Pipe...
Notes
Remote control
2
PIC
MUTE
4
B
SHARP
O-SCAN NRGAMMA
C-TEMP TESTLENS
3D
SWAP
3D
FORMAT
2D/3D
ENTER
SOURCE
3
5
1
ASPECT
RATIO
MENU
USER MEMORY
CA
|
ON POWER OFF
14
16
17
13
15
18
19
20

page 9
Digital Projection M-Vision 930 Series
Installation and Quick-Start Guide
REMOTE CONTROL
Rev C February 2015
Infrared reception
The projector has infrared sensors at the front and back.
The angle of acceptance is 40°. Make sure that the remote control is within the angle of acceptance
when trying to control the projector.
40°
40°
Infrared reception
Notes

page 10
Digital Projection M-Vision 930 Series
Installation and Quick-Start Guide
REMOTE CONTROL
Rev C February 2015
Remote control troubleshooting
The remote control is shipped with no battery tted. Remove the back cover and insert the
supplied cells while observing the correct cell polarity.
If the projector fails to respond to keypress on the remote control, consider the following checks:
• Does the Transmit indicator ash when a button is pressed?
The Transmit indicator 1should be dark when the remote control is not being used and
ash when a button is being pressed. If the Transmit indicator fails to ash when a button
is pressed, it might be time to replace the battery. Use only Alkaline AA (LR6) cells for best
results.
• Is the remote control enabled?
The remote control can be disabled from the menu. Using the control panel:
1. Open the OSD and navigate to the Setup menu.
2. Ensure Infrared Remote is set to On.
• Is the angle of acceptance met?
The projector is equipped with IR sensors at the front and back. If the remote control
transmits from one side, the sensors may not be able to receive the signal. Change your
position so the remote control signal is within the angle of acceptance.
• Is the projector connected to an input source?
Some buttons on the remote control will only work if the projector is connected to an input
source.
Check if an input source is connected. If necessary, connect an input source and try again.
• Is the projector in LENS ADJUSTMENT mode?
LENS ADJUSTMENT mode is actrivated when the LENS button is pressed. In LENS
ADJUSTMENT mode:
• The remote control backlight is on.
• The Lens Control OSD page is displayed on the screen.
• Some remote control buttons are disabled.
To exit LENS ADJUSTMENT mode, either press MENU or wait until LENS ADJUSTMENT
times out.
Notes
For information about the Infrared
Remote setting, see Setup menu in
the Operating Guide.
For information about the angle of
acceptance, see Infrared reception
earlier in this guide.
For information about connecting
the projector to an input source, see:
• Selecting an input signal or
test pattern later in this guide.
• Signal Inputs in the
Connection Guide.
• Main menu in the Operating
Guide.
For information about LENS
ADJUSTMENT mode, see
Adjusting the lens later in this
guide.
Remote control
2
PIC
MUTE
4
B
SHARP
O-SCAN NRGAMMA
C-TEMP TESTLENS
3D
SWAP
3D
FORMAT
2D/3D
ENTER
SOURCE
3
5
1
ASPECT
RATIO
MENU
USER MEMORY
CA
|
ON POWER OFF
1

page 11
Digital Projection M-Vision 930 Series
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Rev C February 2015
Positioning The Screen And Projector
1. Install the screen, ensuring that it is in the best position for viewing by your audience.
2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to ll the screen. Set the adjustable feet so that
the projector is level, and perpendicular to the screen.
The drawing below shows the positions of the feet for table mounting, and the xing holes for ceiling mounting.
1Four adjustable feet
2Six M6 holes for ceiling mount
The screws should not penetrate more than 15 mm into the body of the projector.
Notes
Always allow the projector
to cool for 5 minutes before
disconnecting the power or
moving the projector.
Ensure that there is at least 30
cm (12 in) of space between the
ventilation outlets and any wall,
and 10 cm (4 in) on all other
sides.
Do not stack more than 3
projectors.
Do not tilt the projector more than
±12° from side to side when in
use, as this may cause system
failure.
±12° 360°
1
2
1
1
1
2
2
2
2
2

page 12
Digital Projection M-Vision 930 Series
Installation and Quick-Start Guide
CHANGING THE LENS
Rev C February 2015
Changing The Lens
Inserting a new lens
1. Remove the lens cover.
2. Insert the lens, keeping
the connector in upright
position.
3. Rotate the lens clockwise
until it clicks into place.
Notes
Before changing the lens,
always make sure the projector
is switched off and fully
disconnected from its power
supply.
When changing the lens, avoid
using excessive force as this may
damage the equipment.
Take care to preserve the original
lens packaging and protective caps
for future use.