dji MATRICE 600 User manual

I. Checking the Battery
1. EnsurethatyourrmwareandDJIGOappareup-
to-date.LaunchDJIGOapptoconrmthatallthe
batterycellsarefullychargedtothesamevoltage
level.Ifallthecellsareabove3.7Vbutonecelldiffers
by0.2Vormore,contactDJITMforanalysis.Youcan
alsocheckthebatterywarninghistory.Ifanywarning
isreported,contactDJI.
2. Checktheelectrodesinthebatterycompartment.
Return-to-factoryservicewillberequirediftheyappear
severelyburnt.
3. Check the battery compartment’s plastic components
to ensure that they are in good condition and that all
screws are secure. This prevents the battery from
becoming loose during ight.
4. Check the contact pins in the battery compartment
to ensure that they are clear. They should be able to
establish easy contact with the battery and should not
be bent.
5. Check the battery for damage and deformities. If there
are any signs of severe damage to the battery, stop
using it and discharge the battery to 10% or below
for disposal. Do not disassemble the battery for any
reason.
6. Check the battery’s gold ngers besides the battery
port and rub them clean with an eraser if any residue
is observed. This will help to ensure a more reliable
connection.
7. Check the battery port’s metal connectors for damage.
Replace the battery immediately if the connectors
appear severely burnt.
8. For long term storage, refer to the Intelligent Flight
Battery Safety Guidelines and check the battery once
a month to avoid damage to the battery.
II. Checking the Center Frame
1. Check the upper and lower plates of the center frame
for cracks and damage. If wear exists, but you’re not
sure whether it is safe to y, contact DJI Support for
help.
2. Check the red knob for wear, e.g. if the frame arm is
loose after the knob is locked. If it is, replace the knob
with a spare knob that comes with the MATRICETM 600.
3. Turn on the aircraft and listen for any abnormal noise
or vibration from the cooling fan located on the upper
cover of the aircraft. If a loud noise is detected,
replace the fan.
4. Check the damper on the ight controller for wear and
severe deformities.
5. Checkallthecableconnectionsontheightcontroller
andLightbridge2AirSystem.
6. Checkthesquareheadscrewsonthepowercablesof
theframearmatthebottomofthecenterframe.Use
thesquaresocketwrenchthatcomeswiththeMatrice
600totightenthescrewsifloose.
7. Check the screws connected to the expansion mounting
kit and center frame. Apply medium strength threadlocker
and then tighten the screws if loose.
8. Check the screws connected to the retractable
modules and center frame. Apply medium strength
threadlocker and then tighten the screws if loose.
III. Checking the Foldable Frame Arms
1. Check if the frame arm can move freely, e.g. if the
frame arm is loose after the knob is locked. If it is, but
the knob is in good condition, tighten the screw at the
connection point.
To ensure optimal performance and ight safety for your aircraft, comprehensivemaintenanceisrecommended
every50ightsorafteryingforover20hours.This manual is intended to help users maintain their aircraft for
maximum reliability.
Maintenance Manual
MATRICE 600
2016.06
V1.0
1
Screw

2. Check the motor base for cracks and damage. If wear
exists, but you’re not sure whether it is safe to y,
contact DJI Support for help.
3. Check the connection between the motor base and
the arm tube.
4. Check if the propeller ends on two neighboring
frame arms are aligned. If the vertical difference is
over 1 cm, use the arm inclination holder to adjust
the arm inclination.
IV. Checking the Retractable Landing Gear
1. Check the servo cables for wear. Ensure that the
connection points are secure.
2. Check the power cable connector for wear. Replace
the connector or return to factory for repairs.
3. Hold the aircraft body, and then raise and lower the
landing gear to the ground several times to ensure that
the retractable landing gear can move freely.
4. Check if there is any white plastic debris around the
shaft screws of the landing gear. If there are, replace
the washers under the screws.
5. Checkthepropellers.Ifthereisanybending,breakage
orcracksonapropeller,donotuseit.
6. Attachthepropellertothemotor,turnontheaircraft,
andplaceitontheground.Stand3metersaway
fromtheaircraftandobservethespinningpropellers.
Ifyoucanseetwodistinctpropelleroutlinelayers,
whenlookingataspinningpropellerfromtheside,this
propellerisdamaged.Thiswillincreasetheaircraft
vibrationandreduceightsafetyandperformance.
Replacethepropeller.
VI. Checking the IMU
1. Ensure that your rmware and DJI GO app are up-to-
date. Launch DJI GO app to check the condition of the
IMU and perform an advanced IMU calibration. Place
the aircraft in a cool environment and on a at, stable
surface. Do not touch the aircraft during calibration.
VII. Checking the GPS-Compass Pro
1. Checkthemoduletomakesureitissecurelymounted.
Ensurethatthearrowonitpointstothefrontofthe
aircraft.
2. Ensure that your rmware and DJI Assistant 2 are up-
to-date. Launch DJI Assistant 2 to check the mounting
position settings to ensure that they are correct.
VIII. Checking the Control and Video Transmission System
1. Check the two antennas on the landing gear legs to
ensure that they are secure. Check the antenna cables
at the bottom of the center frame or on the Lightbridge
2 Air System for any bending or damage. Ensure that
they are securely connected. (Note: Attach or detach
the cable in the direction aligned to the connector pin
to avoid damage.)
2. Check the remote controller antennas for damage.
5. Check the shaft screws of the landing gear. If they
are loose, apply high strength threadlocker and then
tighten the screws. It is recommended to afx the
screws with 0.45±0.05 N∙m torque.
V. Checking the Propulsion System
1. Checkthemotorrotorbygentlyshakingitupand
down.Ifitisobviouslyloose,butyou’renotsure
whetheritissafetoy,contactDJISupportforhelp.
2. Checkthemotorsfordeformitiesbyconrmingthatthe
gapbetweenthemotorandmotorbaseiseven,and
themotorspinsfreelyandlooksne.Ifnot,replacethe
motors.
3. Removethepropellersandstartthemotors.Carefully
examinetheedgeofthemotorrotorandconrmthat
theshaftisperfectlycenteredonthemotor.Check
foranyabnormalorexcessivevibration.Ifexcessive
vibrationisdetected,replacethemotors.
4. Removethepropellersandstartthemotors.Listen
carefullyforanyabnormalnoise,whichmayindicate
thatthebearingshavewornoutandthemotorsneed
tobereplaced.
Washers ShaftScrews
DJI Support
http://www.dji.com/support
Recommended Server Center
http://www.dji.com/service/repair
Fordetailsonourafter-salespolicy,visit:
http://www.dji.com/service.
Ifyouareunabletoviewthewebpageorwouldliketo
requestahardcopyofourpolicy,pleasecontactyourlocal
DJIbranchofceorauthorizeddealer.
2

MATRICETM is a trademark of DJI.
Copyright © 2016 DJI All Rights Reserved.
Antennas
PropulsionSystem
CenterFrame
GPS-CompassPro
Lightbridge2AirSystem
FlightController(IMUBuilt-in)
IntelligentFlightBatteries
FoldableFrameArms
RetractableLandingGear
The content is subject to change.
Download the latest version from
http://www.dji.com/product/matrice600