DMP Electronics 734N Series Installation guide

INSTALLATION AND PROGRAMMING GUIDE
734N Series Access
Control Modules

About the 734N Series .............................. 1
Power Supply ................................................................... 1
Zone Terminals................................................................. 1
Annunciators..................................................................... 1
Indicator LEDs.................................................................. 1
Form C Relay ................................................................... 2
Programming Connection .......................................... 2
Wiegand and OSDP Reader Support..................... 2
Local Event Storage...................................................... 2
PCB Features...............................................3
Install the 734N Series Module.................4
Mount the 734N.............................................................. 4
Wire the Access Control Lock .................................. 5
Isolation Relay (optional)............................................ 8
Install the 333Suppressor.......................................... 9
Wire the Zone Terminals ............................................10
Connect a Wiegand Card Reader...........................12
Connect an OSDP Card Reader ..............................15
Network Connection....................................................19
Set the 734N Address................................................20
Connect the Power Supply ...................................... 22
TABLE OF CONTENTS
Program the Panel....................................23
Device Setup..................................................................23
Device Number .................................................................23
Device Name......................................................................23
Device Type........................................................................24
Communication Type......................................................24
Program the 734N Series Module..........25
734N Menu ...................................................26
Programmer Menu.......................................................26
Initialization Options................................................... 27
Initialize Communication ............................................. 27
Initialize Access ............................................................... 27
Communication Menu ................................................28
734N Device Number .....................................................28
734N DHCP ........................................................................28
734N IP Address...............................................................28
Subnet Mask.......................................................................28
Gateway Address .............................................................29
Panel IP Address...............................................................29
Panel IP Port ......................................................................29
734N Passphrase..............................................................29

Access Options............................................................ 30
Reader Protocol Type.................................................... 30
Activate Zone 2Bypass .................................................32
Activate Zone 3 Request to Exit.................................34
Activate Onboard Speaker ...........................................35
Card Formats.....................................................................35
Require Site Code............................................................38
Number of User Code Digits .......................................39
Card Format Added/Changed (Custom Format)40
No Communication with Panel .................................. 40
Stop ...................................................................................41
Test the 734N Series Module ................. 42
734N Menu ...................................................42
Diagnostics Menu ............................................................42
Zone Status Display ........................................................43
Public Card Formats ............................... 44
734N Series Network Specifications .... 45
Compliance Listing Specifications ........47
UL Access Control .......................................................47
ULC Commercial Burglary (XR150/XR550Series
Panels)..............................................................................49
Certifications............................................ 50
Underwriters Laboratory (UL Listed) ................. 50
Product Specifications ............................ 51
Readers and Credentials .........................53

Digital Monitoring Products, Inc. | 734N Series Installation and Programming Guide 1
Annunciators
An onboard programmable piezo provides
local annunciation at the module. You can
also connect a variety of switched ground
annunciators to the module for remote
annunciation.
Indicator LEDs
734N Series modules provide three
indicator LEDs:
• RELAY (red) turns on for the same
duration as the door strike relay.
• WIEGAND (yellow) turns on for one
second to indicate receipt of valid input.
• DATA (green) indicates that the module
is communicating with the panel.
The 734N and 734N‑POE Access Control Modules allow you to add IP network access
control capability to XR150/XR550Series panels using proximity, credential, or
mag‑stripe card readers. The modules also allow you to use the powerful built‑in access
control capability of DMP Panels.
Power Supply
734N Series modules operate at
12/24VDC from the power supply
supporting a door’s magnetic lock or
door‑strike. The 734N‑POE can also be
powered from POE.
Warning: To avoid the risk of
equipment damage, do not exceed
750mA total output current for
zones connected to the module.
Zone Terminals
Four input zones are provided to allow
connection of nearby burglary devices.
ABOUT THE 734N SERIES

2 734N Series Installation and Programming Guide | Digital Monitoring Products, Inc.
Form C Relay
The 10Amp Form C relay draws up to
35mA of current. Refer to “Wire the
Access Control Lock” and “Isolation Relay
(optional)” in this document for more
information.
Programming Connection
The modules also provide a keypad
programming connection that allows
you to use a standard DMP LCD keypad
for initial setup. Programming can be
completed using a keypad connected to
the module or from XR150/XR550panels.
Wiegand and OSDP Reader
Support
The 734N Series supports both Wiegand
and OSDP card readers. For information
on compatible readers, refer to “Readers
and Credentials”. OSDP support requires
734N/734N‑POE modules with PCB Rev 9
and higher.
Local Event Storage
When communication is lost with the
panel, 734N and 734N‑POE Access
Control Modules store access granted
events locally in module memory. When
communication is reestablished, stored
events are sent and synced with panel
events, then inserted into the event buer
according to the actual time when they
occurred. To enable local event storage,
CARD FORMAT must be set to DMP or
CUSTOM and NO COMM WITH PNL must
be set to SITE or ANY.
Local Event Storage requires 734N/734N‑
POE modules with firmware Version 105
or higher, along with XR Series firmware
Version 202 or higher.

Digital Monitoring Products, Inc. | 734N Series Installation and Programming Guide 3
PCB FEATURES
DC
Input
Reader
Inputs Zones
Piezo
Indicator
LEDs
Door Relay
Network
Connection
Figure 1: PCB Features
Keypad
Programming
Header
Status
Indicator
Outputs
Output 1
Reset Header
Output 2

4 734N Series Installation and Programming Guide | Digital Monitoring Products, Inc.
INSTALL THE 734N SERIES MODULE
Mount the 734N
The module comes in a high‑impact plastic housing that you can mount directly to a
wall, backboard, or other flat surface.
For easy installation, the back and ends of the 734N housing have wire entrances. The
back also contains multiple mounting holes that allow you to mount the module on
a single‑gang switch box. DMP recommends mounting the 734N near the protected
door. Refer to Figure 2for mounting hole locations on the housing base.
1
1. Remove the PCB from the
plastic housing by loosening
the clips on one side and gently
lifting it out of the housing base.
2. Insert the included screws in the
desired mounting hole locations
and tighten them to secure the
housing to the surface.
3. Reinstall the PCB in the housing
base.
Mounting Holes
Figure 2: Mounting Hole Locations

Digital Monitoring Products, Inc. | 734N Series Installation and Programming Guide 5
Wire the Access Control Lock
The module provides a Form C (SPDT) relay for controlling locks and other
electronically‑controlled barriers. The three relay terminals marked NO C NC allow
you to connect the device wiring to the relay for module control.
When the 734N Series module is powered with a 12/24V power supply, the device
can power an electric strike, up to 750mA. See Figure 3 and Figure 4 for typical
magnetic lock and door strike wiring. The 734N‑POE can also be powered with POE.
See Figure 5for POE door strike wiring.
The Form C relay draws up to 35mA of current and contacts are rated for 10Amps
(resistive) at 12/24VDC. When connecting multiple locks to the Form C relay, the
total current for all locks cannot exceed 10Amps. If the total current for all locks
exceeds 10Amps, problems may arise and an isolation relay may be needed. See
“Isolation Relay (optional)” for more information.
2

6 734N Series Installation and Programming Guide | Digital Monitoring Products, Inc.
Model 333
Suppressor
–+
12/24 VDC
Power Supply
734N
Normally Closed
Magnetic Door
Lock
Mag lock positive
to 734N terminal NC
Power supply positive
to 734N terminal C
Mag lock negative to
power supply negative
Figure 3: Typical Magnetic Lock Wiring
Model 333
Suppressor
–+
12/24 VDC
Power Supply
734N
Normally Open
Door strike positive
to 734N terminal NO
Power supply positive
to 734N terminal C
Door strike negative to
power supply negative
DC Door Strike
Figure 4: Typical Door Strike Wiring