DMP Electronics Wiegand 734N Installation guide

INSTALLATION AND PROGRAMMING GUIDE
734N Wiegand
Interface Module

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide a
Table of Contents .......................................a
About the 734N .......................................... 1
Power Supply......................................................... 1
Zone Terminals ...................................................... 1
Annunciators.......................................................... 1
Indicator LEDs ....................................................... 1
Form C Relay......................................................... 2
Programming Connection................................ 2
Keypad In and Out Connections ................... 2
PCB Features...............................................3
Install the 734N...........................................4
Mount the 734N ................................................... 4
Wire the Electronic Lock.................................. 5
Isolation Relay ...................................................... 6
Install the 333 Suppressor ............................... 7
Wire the Zone Terminals................................... 8
Connect a Card Reader....................................10
Set the 734N’s Address....................................12
TABLE OF CONTENTS
Program the 734N.................................... 15
Program Start Display ...................................... 15
Initialization Option ...........................................15
Initialize Confirm Option .................................16
Activate Zone 2 Bypass...................................16
zone 2 Bypass Time...........................................17
Relock on zone 2 Change ...............................17
Activate zone 3 Request to Exit...................18
Zone 3 REX Strike Time...................................19
Activate On-board Speaker ...........................19
Card Options........................................................19
Custom Card Definitions ......................... 21
Wiegand Code Length..................................... 21
Site Code Position and Length .....................21
User Code Position and Length................... 22
Require Site Code .............................................22
Site Code Display ..............................................22
Enter Site Code .................................................23
Number of User Code Digits.........................23

b 734 Installation and Programming Guide | Digital Monitoring Products, Inc.
No Communication with Panel ....................24
Remove Keypad.................................................25
Keypad Bus Wiring Specifications........ 26
Compliance Listing Specifications ........27
UL Commercial Fire.......................................... 27
UL Access Control............................................. 27
ULC Commercial Burglary (XR150/XR550
Series Panels)...................................................... 27
Certifications.............................................28
Underwriters Laboratory (UL Listed)........28
International Certifications.................... 29
Intertek (ETL) Listed........................................29
Product Specifications ........................... 30
Accessories................................................ 31
Proximity Readers..............................................31
Proximity Credentials........................................31

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide 1
ANNUNCIATORS
An on-board programmable piezo provides local
annunciation at the 734N. You can also connect
a variety of switched ground annunciators to the
734N for remote annunciation.
INDICATOR LEDS
The 734N provides three indicator LEDs. The
red LED turns on for the same duration as the
door strike relay. The yellow LED turns on for one
second to indicate receipt of a valid Wiegand
input. The green LED indicates that data is being
sent to the panel.
The 734N Wiegand Interface Module allows you to add IP network access control capability to
XR150/XR550 Series and XR150INT/XR550INT Series panels using proximity credential or mag-stripe
card readers. It also allows you to use the powerful built-in access control capability of DMP Panels.
DMP panels provide access control, arming, and disarming using proximity, mag-stripe, biometric or
other Wiegand-output authentication devices.
Connect a 734N to a DMP panel’s keypad bus or AX-Bus™to use the powerful built-in access control
capability of DMP panels. The 734N includes the following features:
POWER SUPPLY
The 734N operates at 12/24VDC from the power
supply supporting a door’s magnetic lock or
door-strike. It also provides a 10 Amp Form C
relay contact for lock control.
ZONE TERMINALS
Zones 1, 2, and 3 on the 734N can be
programmed for a variety of burglary or access
control applications. Zone 4 is a class B, style A
circuit that may be programmed as a fire zone.
ABOUT THE 734N

2 734 Installation and Programming Guide | Digital Monitoring Products, Inc.
FORM C RELAY
The 734N’s Form C relay draws up to 35mA of
current. Refer to the NC/C/NO (Dry Contact
Relay) and the Isolation Relay sections in this
document for more information.
PROGRAMMING CONNECTION
The 734N also provides a keypad programming
connection that allows you to use a standard
DMP LCD keypad for initial setup. Programming
can be completed using a keypad connected to
the 734N, or from XR150/XR550 or XR150INT/
XR550INT Series panels.
KEYPAD IN AND OUT
CONNECTIONS
The keypad in (KYPD IN) connection receives
and transmits data to the panel keypad bus or
AX-Bus™.
The keypad out (KYPD OUT) connection receives
and transmits data out to other keypad(s) or
module(s). Install a dual connector four-position
harness to allow daisy chain connection to other
devices, up to the maximum number of devices
supported. XR150 Series panels support up to 8
devices. XR550 Series panels support up to 16
devices.
When the 734N is powered from 24VDC,
do not connect devices to KYPD OUT
header.

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide 3
PCB FEATURES
DC INPUT
WIEGAND
INPUTS ZONES
PIEZO
INDICATOR
LEDS
DOOR RELAY
NETWORK
CONNECTION

4 734 Installation and Programming Guide | Digital Monitoring Products, Inc.
INSTALL THE 734N
The 734N comes in a high-impact plastic housing that you can mount directly to a wall,
backboard, or other flat surface.
For easy installation, the back and ends of the 734N housing have wire entrances. The back also
contains multiple screw holes that allow you to mount the 734N on a single-gang switch box. DMP
recommends mounting the 734N near the protected door.
You can also mount the 734N in a panel enclosure by following these steps:
1. Remove the 734N PCB from the plastic housing.
2. Mount the plastic standos to the panel enclosure by pressing them into place.
3. Snap the 734N onto the standos.
1MOUNT THE 734N

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide 5
The 734N provides a Form C (SPDT) relay for controlling locks and other electronically-
controlled barriers. The three relay terminals marked NO C NC allow you to connect the device
wiring to the relay for module control.
Use an additional power supply to power magnetic locks and door strikes. See Figures 2 and 3
for typical magnetic lock and door strike wiring.
The Form C relay draws up to 35mA of current and contacts are rated for 10 Amps (resistive)
at 12/24VDC. When connecting multiple locks to the Form C relay, the total current for all locks
cannot exceed 10 Amps. If the total current for all locks exceeds 10 Amps, problems may arise
and an isolation relay may be needed. See the Isolation Relay section for information.
2WIRE THE ELECTRONIC LOCK
PROG
J2
RED RED
KYPD IN
J4
J1
DATA
XMT LED
WIEGAND
READ LED
RELAY
ON
NCCNO
GRNYELRED
Model 333
Supressor
Normally Closed
–
+
Magnetic Door Lock
12/24VDC
Power Supply
Figure 2: Typical Magnetic
Lock Wiring
PROG
J2
RED
J1
DATA
XMT LED
WIEGAND
READ LED
RELAY
ON
NCCNO
GRNYELRED
Model 333
Supressor
Normally Open
–+
DC Door Strike
12/24VDC
Power Supply
Figure 3: Typical Door
Strike Wiring

6 734 Installation and Programming Guide | Digital Monitoring Products, Inc.
The Form C relay can control a device that draws less than 10 Amps of current. If a device draws
more than 10 Amp of current, or the sum of all devices controlled by the Form C relay exceeds
10 Amps, an isolation relay must be used. Refer to Figures 5 and 6 for isolation relay wiring.
3ISOLATION RELAY
Figure 4: Magnetic Lock with
an Isolation Relay
Figure 5: Door Strike with an
Isolation Relay
(optional)
Normally
Closed
Magnetic Lock Model 333
Supressor
–+
12/24VDC
Power
Supply
734N
Interface
Module
DC Input
Model 333
Supressor
Normally
Open
–+
DC Door Strike
12/24VDC
Power
Supply
734N
Interface
Module
DC Input