Dogtra iQ MINI User manual

1
iQ MINI
EXPANDABLE TO 2-DOG SYSTEM
Owner’s Manual
Please read this manual thoroughly before
operating the iQ MINI training e-collar.

6
AT A GLANCE
Optional Accessories
Auto Charger: The auto charger for the iQ MINI has an input of 12-volts to 24-volts and
has an output of 5-volts 1000mAH.
European Charger: designed for use with 230 volt AC electrical outlets in Europe.
To purchase optional accessories, please visit www.dogtra.com or
call our customer service at [phone].
Transmitter Receiver Battery
Charger
Cradle Splitter
Cable
Owner’s Manual

7
MAIN FEATURES
• Easy-to-use, ergonomically fitted
transmitter
• Front-facing Rheostat Dial that allows
for gradual adjustments in stimulation
intensity with no jumps between levels
(0-100)
• Expandable to 2-dogs
• 400-yard range
• Nick/Constant stimulation & Pager
vibration
• 2-hour rapid charge batteries
• 1.3 oz. petite receiver
• Conductive plastic contact points for
sensitive skin
• For dogs as small as 7 pounds

8
OVERVIEW
iQ MINI
Transmitter
Rheostat
Dial
1st Dog/2nd Dog
Toggle Switch
LED Indicator
Light
On/Off Magnetic
Red Dot
Battery Charging
Receptacle &
Rubber Plug
Nick
Constant
Pager
Antenna

9
iQ MINI
Receiver
Collar Strap
LED Indicator
Light
Battery Charging
Receptacle
On/Off Magnetic
Red Dot
Conductive Plastic Contact Points
Conductive
Plastic
Contact
Points

10
To turn the receiver on, place the red dot
on the back of the handheld transmitter
to the red dot on the receiver. Hold the
two red dots together for a moment until
the LED light on the receiver comes on.
To turn the receiver off, repeat the same
procedure holding the two red dots
together momentarily. The LED light will
turn red for a brief moment indicating
that the receiver is now off.
The handheld transmitter does not have
an on/off button and it will only activate
when the buttons are pressed.
UNDERSTANDING YOUR TRAINING SYSTEM
1. Turning the iQ MINI On/Off

11
2. Transmitter Button Function N - Nick Button
When the Nick button is pressed, the
receiver emits a single rapid pulse of
electrical stimulation.
C - Constant Button
Pressing the Constant button gives
continuous stimulation as long as
the button is pushed, for up to 12
seconds. If the button is not released
after 12 seconds, the stimulation will
automatically turn off as a safety feature.
P - Pager Button
Pressing the Pager button will give a
vibration for as long as the button is
pressed, for up to 12 seconds.

12
The 1st Dog/2nd Dog Toggle Switch is
on the left of the Rheostat Dial.
I - 1st Dog
Slide the switch to the left underneath
“I” and press any of the buttons to
operate the first receiver.
II - 2nd Dog
Slide the switch to the right underneath
“II” and press any of the buttons to
operate the second receiver.
1st Dog 2nd Dog
1st Dog/2nd Dog Toggle Switch

13
Proper Fit
The receiver should be fitted so that the
conductive plastic contact points press
firmly against the dog’s skin. You should
be able to fit two fingers underneath the
collar strap. The best location is on either
side of the dog’s windpipe.
Improper Fit
A loose fit can allow the receiver to move
around on the dog’s neck. When this
happens, the contact points may rub
against the skin and cause irritation. If the
receiver is too loose, the contact will not
be consistent and cause the corrections
to be inconsistent.
3. Receiver Fitting

14
Attention!
Leaving the receiver in the same
location on the dog’s neck for an
extended period of time can cause
skin irritation due to the sensitivity
from the contact points. If the dog is
to wear the receiver for long periods,
occasionally reposition the receiver
every few hours so that the contact
points are moved to a different
location on the dog’s neck and remove
the receiver after eight hours of usage.
Make sure you check for skin irritation
each time you use the unit.

15
The iQ MINI has a Rheostat Dial on the
front of the transmitter (0 is the lowest
and 100 is the highest). Remember
that you will need to adjust the setting
(upward or downward) depending on
your dog’s temperament and threshold
for stimulation. Always start at the
lowest level and work your way up. The
appropriate level can be found when the
dog responds to the stimulation with a
mild reaction. Also, as the dog’s attitude
changes, especially during times of
increased excitement or distraction, you
may need to adjust the intensity level.
Note: The stimulation intensity can be
adjusted even when the stimulation is in
use.
4. Finding the Right Stimulation

16
The iQ MINI has a 400-yard range.
Depending on the way you use your
transmitter, the transmitter range may
vary.
Typical range
Maximum range Minimum range
5. Maximizing the Distance
To get the greatest range, hold the
transmitter away from your body and
avoid touching the antenna. Keep your
unit properly charged for maximum
signal strength.

17
The LED indicator flashes every
4 seconds when the receiver is on and
ready for use. The LED indicator will
light up on both the transmitter and the
receiver when the transmitter buttons
are pressed.
6. LED Indicator
The LED color indicates battery life level.
Green = Full charge
Amber = Medium charge
Red = Needs charge
If the unit is used while the LED indicator
is red, it may shut down automatically.

18
The Dogtra iQ MINI uses a lithium
polymer battery. Recharge the unit if the
indicator light is red, the unit does not
turn on, or the system will not stay on
when any button is pressed.
NOTE 1: Only use Dogtra-approved
batteries, chargers, and accessories for
your Dogtra e-collars. This will prevent
any damage that can be incurred from
attempting to use a different charger.
NOTE 2: The unit has a partial charge
when it leaves the Dogtra facility. Upon
receipt of the system, be sure to give
it a full 2-hour initial charge before
the first use away from any flammable
substances.
7. Charging the Battery

19
NOTE 3: When a charger is not in use,
disconnect it from the power source.
Fully charge the batteries if the unit is to
be stored without use for a period of
3 months or more.
Follow the steps below to charge your
system:
1. Open the rubber plug on the battery
charging receptacle on the transmitter
and plug in the charging cable.
To charge the receiver, use the cradle
charger and attach it using the
instructions on the following page.
2. Plug the charger into a 120-volt wall
outlet or, if using the auto charger,
plug into a cigarette lighter only for
lithium polymer batteries (use a 220
volt European charger for Europe).
All indicator lights should glow red
when properly charging and the unit
will automatically shut off during the
charging process. You will need to turn
the unit on again before use once the
unit is fully charged and unplugged
from the battery cable.
3. The lithium polymer battery is fully
charged within 2 hours. The lights will
stay red during the charging process
and turn green once the unit is fully
charged.
4. After charging, cover the battery
charging receptacle on the transmitter
with the rubber plug and detach the
cradle charger from the receiver.

20
Attention! To attach the charger:
1. Align the clear plastic piece on the
charger to the LED screen on the
receiver.
2. Press the charger onto the receiver
until you hear a snap to secure the
placement.
LED Indicator Light

21
To detach the charger:
3. Pull on the tab at the bottom of the charger to remove it from the receiver.

22
8. Code Setting
Coding the 1st Dog Position:
1. Set the Rheostat Dial to 0 and place
the toggle switch in “I” position.
2. With the receiver turned off, place the
red dot on the back of the transmitter
to the red dot on the receiver. Hold
the two red dots together for about
5 seconds until the green LED blinks
rapidly on the receiver.
3. While the green LED is rapidly blinking
on the receiver, separate the two
devices and press the two top buttons
(Nick & Constant) simultaneously on
the transmitter. The LED light on the
receiver will blink every 4 seconds
when coding is complete.
Coding the 2nd Dog Position:
1. Set the Rheostat Dial to 0 and place
the toggle switch in “II” position.
2. With the receiver turned off, place the
red dot on the back of the transmitter
to the red dot on the receiver. Hold
the two red dots together for about
5 seconds until the green LED blinks
rapidly on the receiver.
3. While the green LED is rapidly blinking
on the receiver, separate the two
devices and press the two top buttons
(Nick & Constant) simultaneously on
the transmitter. The LED light on the
receiver will blink every 4 seconds
when coding is complete.

23
GENERAL TRAINING TIPS
Your dog must know some basic
obedience commands before beginning
training with the iQ MINI. A dog learns by
first being shown a command, followed
by lots of repetition over an extended
period. As the dog becomes proficient
at these commands, the trainer can
introduce distractions and different
locations to strengthen them.
Obedience Training on the Leash
Your dog must fully understand the
obedience commands (sit, stay, here,
heel, and kennel) before using the
e-collar for reinforcement of these
commands. A leash attached to a
standard collar is used to "teach" the dog
the basic obedience commands (here,
heel, sit, and stay). A tug on the leash/
collar is used to reinforce the command.
When the dog complies with the
command, use positive reinforcement/
praise. Once the dog understands these
commands, the e-collar can be used to
reinforce them.
Beginning E-Collar Training
When you feel your dog understands
the obedience commands on the leash
we can now start with the e-collar
training. With the dog on the leash and
wearing the e-collar, continue with your
obedience drills. Apply light stimulation

24
(Nick or Constant) when a command is
given; the stimulation can be removed
as the dog complies. Through repetition,
the dog learns to perform the command.
The final step is the avoidance phase in
which the dog learns that he can avoid
the stimulation altogether by performing
your commands. When these training
procedures are complete, the e-collar
is used as a reminder when the dog
does not comply with your commands
at home or in the field. Keep your initial
training sessions short and positive as
dogs have a short attention span.
How Much Stimulation to Use
Always start with low levels of stimulation
and work your way up depending on
the disposition of your dog and the
given situation. By using the correct
amount of stimulation to get your point
across, you will have a more controllable
environment and a dog that is under less
stress. Animals (and humans) perform
better in a less stressful environment.
For more training information, please
visit our website at www.dogtra.com.