Draper 220V Signature/Series E Manual

Installation/Operating Instructions
220V Signature/Series E & V Electric Projection Screen
These instructions are meant as a guide only. They do not imply any
responsibility on the part of Draper, Inc. for improper installation or faulty
workmanship at the jobsite.
Adjustments
Screen has been factory set and should not require further adjustment. How-
ever, if you wish to change the “up” and “down” stopping positions, proceed as
follows:
CAUTION: Be sure all switches are in “off” position before adjusting limit
switches. Always be prepared to shut screen off manually when new ad-
justment is being tested. Screen may be severely damaged if viewing surface
is allowed to run too far up or too far down.
Adjusting “Fully Up” Position—“Up” stopping position may be adjusted by
turning the yellow llimit switch adjustment socket. The yellow socket is located
on left end of screen roller and is accessible to a screwdriver/Allen wrench
(4mm or
5
/ 32 ").Turning the socket counterclockwise will allow the viewing sur-
face to retract further into the case. Turning it clockwise will cause the surface
to stop further out of the case. One full revolution of the socket will alter the
stopping position of the viewing surface by approximately 3.8 cm.
Adjusting “Fully Down” Position—“Down” stopping position may be
adjusted by turning the white limit switch adjustment socket. The white socket
is located on the left end of screen roller and is accessible to a small flat
screwdriver/Allen wrench (4mm or
5
/ 32 "). Turning the socket counterclockwise
will allow the viewing surface to run farther down. Turning it clockwise will
shorten the viewing surface, causing it to stop in a less extended position. At
no time should viewing surface be unrolled enough to expose any part of the
screen roller.
Please note: See page 2 for information on adjusting Tab-Tensioning cables
on Signature/Series V screens.
Copyright © 2006 Draper Inc. Form Signature220V_Inst06 Printed in U.S.A.
These Installation/Operating Instructions are available in the official
language of the country where you purchase the product. Please contact your
distributor to request a copy.
Vous pourriez demander les instructions d’installation et d’opération
traduises dans la langue officielle du pays ou vous achetez le produit. Veuillez
demander à votre distributeur.
Die Gebrauchsanweisung für Installation und Konstruktion sind in der
offiziellen Sprache des Landes, indem Sie das Produkt gekauft haben,
vorhanden. Fragen Sie die jeweilige Verkaufs-Abteilung.
Caution
➀Read instructions through completely before proceeding.
➁Follow instructions carefully. Installation contrary to instructions
invalidates warranty.
➂Entire bottom of screen case should be unobstructed to permit proper
operation of automatic trap door, and access to bottom panel for
making electrical connections or servicing.
➃Screen should be installed level (using a carpenter’s level).
➄Nothing should be fastened to screen dowel, viewing surface or
automatic trap door.
➅Operating switch(es) is packed separately in screen carton. Do not
discard with packing material.
➆Screen operates on 220V, 50 Hz. current.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
Hanging Screen
When locating viewing surface and checking clearance for screen’s operation,
remember that the surface is centered in case. Screen is normally recessed
above ceiling and may be installed in a variety of ways. See details on back of
this sheet. Regardless of mounting method used, the following points apply:
➀Screen should be positively and securely supported so that vibration or
even abusive pulling on viewing surface will not weaken installation.
➁Installer must insure that fasteners used are of adequate strength and
suitable for the mounting surface chosen.
➂Entire bottom of case must be readily accessible after installation.
➃The hinge that connects bottom panel and automatic trap door of screen
must be permitted to operate freely. Front and back of case must be
straight—not forced to warp or bow. Hinges must be free from mastic or
paint buildup, and doors must be unobstructed by ceiling tiles.
➄Do not use screen case to support adjacent sections of ceiling.
➅If trim pieces must be attached to case, do not permit screws to protrude
more than 6.35 mm through 3.2 mm wall of case. Do not attach trim pieces
with nails.
➆If case is painted, slots on bottom of case should be shielded to protect
viewing surface from paint splatters or overspray.
➇Do not seal unit in ceiling until electrical connections have been made and
screen has been operated successfully.
Electrical Connections
Screen operates on 220V., 50 Hz., 1 ph. current. Junction box is located just
above the access plate at left end of screen. Access plate is held closed with
flathead screws and may be opened with a Phillips screwdriver. (Automatic
trap door does not need to be opened to make field connections.) Removal
of access plate exposes terminal strip, per wiring diagram on reverse. Screen
is shipped with internal wiring complete and control switch(es) fully boxed.
Operation
CAUTION—Important Instructions—Signature/Series V—The shipping
support brackets must be removed from each end of dowel during initial op-
eration before screen is operated in UP direction. After screen is installed, run
viewing surface DOWN to access screws that hold brackets to dowel. Loosen
hex head screw, remove bracket and retighten screw at each end of dowel.
Signature/Series E—The protective paper wrapping around the viewing sur-
face must be removed before the screen is operated in down direction. Cycle
viewing surface down and up several times to confirm satisfactory operation.
If viewing surface or trap door do not operate properly, turn power off and free
trap door and/or check electrical connections.
220V Single Station Control—3-position UP-OFF-DOWN switch permits
operation to be stopped at any point. Factory set limit switches automatically
stop screen when fully down or fully up.
220V Multiple Station Control (Not CE Approved)—Switches are similar in
appearance to Single Station Control. Screen stops when switch is released
and may be restarted in either direction. Factory set limit switches stop screen
automatically when fully up or fully down.
24V Control—Three-button UP-STOP-DOWN switches stop at any point
desired, operate in any sequence. Factory set limit switches automatically
stop screen when fully up or fully down. Wireless controls—whether infrared
or radio frequency—interface with low voltage control box.
Key Operated Switching (Not CE Approved)—Two kinds of key-operated
switches are optionally available with this unit. ➀ The key-operated power
supply switch controls power to the screen and switches. When it is “off”,
the switches will not operate screen. Key may be removed from the switch in
“on” or “off” position. ➁A three-position key switch permits the screen to be
operated directly by key. In this case, the screen’s operator must have a key.
RS232/Ethernet—Serial communication and network communication
optionally available with wall switches, RF or IR remote.
Wire connecting screen to switch(es) and switch(es) to power supply should
be furnished by installer. Connections should be made in accordance with
attached wiring diagram, and wiring should comply with National and local
electrical codes. All operating switches should be “OFF” before power is
connected.
If you encounter any difficulties installing or servic
ing your
Signature screen, call your dealer or Draper, Inc. Spiceland,
Indiana, U.S.A., [phone], FAX [phone], or e-mail to
[email protected].

220V Signature/Series E & V by Draper
Single Station Control
CE Approved
Terminal strip in
junction box at left
end of screen
Dashed wiring
by electrician
Neutral
L1
230V,
50 Hz.
Terminal strip in
junction box at left
end of screen
Dashed wiring
by electrician
Neutral
Hot
Multiple Station Control
Not CE Approved
Cap off with wire
nut & tape
Red
Red
Red
Blue
Blue
Blue
Black
Black
230V, 50 Hz.
Control
switch
Black
PE
Wiring Diagrams
Case Dimensions and Methods of Installation
Page 2 of 2
Dowel Adjustment
Screw
Tensioning
Cable
Draper’s Tab-Tensioning System is factory-set, and
under normal circumstances will not require field
adjustment. If, however, you notice wrinkles, waves, or
other indications that the tensioning cables need to be
adjusted, follow the procedure below.
➀Determine which side requires adjustment.
➁Secure dowel with one hand.
Caution: Do not touch or bend surface.
➂Using Philips-head screwdriver, depress
spring-loaded adjustment screw (see
Fig. 1) and slowly turn clockwise to tighten
tension, or counterclockwise to loosen tension.
The screw adjusts in ¼ turn increments. Adjust
only one increment (¼ turn).
➃If problem is not corrected, leave screen in position
for 24 hours to allow surface material to stretch into position.
➄If problem still is not corrected, repeat steps 2 and 3.
Tab-Tensioning Cable Adjustment
Figure 1
www.draperinc.com (765) 987-799
9
MC1
See separate Serial Communication-RS232 Instruction sheet for
enabling RS232 with the MC1.
3 Button Wall Switch
DOWN - Black
COM - White
UP - Red
Eye Port for IR Eye, RF Receiver or LED
Switch For more than one of these,
a splitter is required.
Aux Port for connecting additional
LVC-III modules (up to six total-
connect from Aux to Eye).
Red-to screen (directional)
Brown-to screen (directional)
White-Common to screen, 110-120V AC
Black-to 110-120V AC
Yellow-to 110-120V AC
Green-Ground
Dashed wiring by electrician
Low voltage wiring by others
Terminal strip in
junction box at left
end of screen
230V, 50 Hz.
Neutral
Hot
All-Pole Disconnect
by Others
STOP
Control
Switches
24v DC
STOP
RS232 Data FROM Control System
RS232 Data TO Control System
Signal Ground & Manual Switch Common
Manual Switch Down
Manual Switch Up
Red-to Screen (directional)
Black-to Screen (directional)
Blue-Common
Brown-Hot to 230V AC
Green/Yellow-Ground
Fuse
Program LED
Eye Port for IR Eye. For RF Receiver
or LED Wall Switch, a Splitter and a
Power Supply is required. Plug RF
Receiver or LED Wall Switch and
Power Supply into splitter, then run
cable from Splitter to MC1 Eye Port.
Low Voltage Wiring by others
AC Wiring by electrician
MC1
Terminal strip in
junction box at left
end of screen
230V, 50 Hz.
Neutral
Hot
All-Pole Disconnect
by Others
STOP
Control
Switches
24v DC
STOP
Low Voltage & Wireless Control
SCREEN SIZE CASE SIZE
Total Drop < 396 cm or viewing width < 366 cm Small
Total Drop > 396 cm or viewing width > 366 cm Large
NOTE: Viewing surface shown is Series V with tab tensioning.
Series E, without tab tensioning, is also available.
Case length
38 mm Typ
Viewing surface
54 mm
A
Series A
E-small case 81 mm
E-large case 114 mm
V Varies
Ceiling grid
and tile
(by others)
232
cm
152
mm
248
cm Audience
Electrical connection
to internal splice box
on left end of case. 22mm
knockout for 13 mm
conduit. J-Box cover located
under splice box.
Shown with
9.5 mm
threaded rod
(provided
by others).
Ceiling grid and tile
(by others)
Audience
Electrical connection
to internal splice box
on left end of case. 22mm
knockout for 13 mm
conduit. J-Box cover located
under splice box.
Shown with
11 mm
threaded
rod (provided
by others).
Ceiling grid and tile
(by others)
232
cm
152
mm
280
cm
Small Signature Case
Large Signature Case