Draper AeroLift 35 Programming manual

Overiew - Components
Contents
Overiew - Components...............................................................................................1
Overview - Planning ....................................................................................................1
Please Read: Warnings and Safety Information ...........................................................2
Section 1 - Hanging Unit .............................................................................................2
Section 2 - Installing Optional Environmental Air Space Housing ..................................3
Section 3 - Installing Projector .....................................................................................3
Section 4 - Electrical Connections...............................................................................4
Section 5 - Wiring Diagrams........................................................................................4
Section 6 - Operation..................................................................................................5
Section 7 - Testing Safety Limit Switches ....................................................................5
Section 8 - Adjustments .............................................................................................6
Section 9 - Installing Ceiling Closure............................................................................7
Installing Optional Ceiling Trim Kit.................................................................................7
Section 10 -Dimensions ..............................................................................................8
Overview - Planning
1 Based on screen location and projector
specifications, determine proper position for projector
installation.
2 Confirm that there is adequate space for installation
and operation. Minimum clearance above ceiling
level varies according to height of projector, optional
projector mounting bracket, optional ceiling closure
and optional Environmental Housing.
3 Arrange to provide service access to the unit.
4 When installed with Environmental Air Space Housing
unit is suitable for use in an environmental air space in
accordance with in accordance with Section 300.22(C)
of the National Electrical Code, and Section 2-128, 12-
010(3) and 12-100 of the Canadian Electrical Code, Part 1,
CSA C22.1.
5 Total capacity of lift is 35 lbs, including closure, projector
and bracket.
As Soon As AeroLift 35 Arrives
1 Open carton and inspect for damage.
2 Locate the following parts:
A. The unit itself
B. Controls
C. Any optional equipment
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
If you have any difficulties installing or servicing your
AeroLift 35, call your dealer or Draper, Inc.
1 Optional closure panel with
threaded rods to attach to
bottom/travelling pan of lift
2 Mounting Brackets
3 Travelling Pan
4 Electrical Junction Box
Please Note: Projector not
included
PROJECTOR
NOT INCLUDED
PROJECTOR
NOT INCLUDED
1
2
3
4
2
2
2
Projector mount optional
Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385
draperinc.com | 765.987.7999 | 800.238.7999
© 2019 All Rights Reserved | FORM: AeroLift35_Inst19
AeroLift 35®
INSTRUCTIONS
INSTALLATION & OPER ATION

Section 1 - Hanging Unit
The AeroLift 35 is provided with four (4) mounting angles for suspending or direct
mounting the unit from above or direct mounting from the sides. These angles provide
up to 1½" of adjustment (front to back). The AeroLift 35 is designed to fit between joists
spaced 16" apart on center (assuming 2" joists), and to close to aproximately 4", not
including the projector, bracket or closure. The unit should be guy wired or blocked to
prevent swinging. All installations should observe the following guidelines:
1 Installer must ensure that all fasteners and supports are of adequate strength
to securely support AeroLift 35 and projector. It is recommended that hardware
structure be able to hold at least four times the combined weight of the lift, projector,
housing, closure and ceiling material attached to closure.
Caution: DO NOT hang from, "ride" or pull down on the unit. This could create a
failure and cause damage and/or injury.
2 Fastening methods must be suitable for mounting surface, and securely anchored so
that vibration or abusive pulling on unit will not weaken installation.
3 Bottom of unit must be unobstructed after installation. Sufficient clearance must be
allowed below projector or optional ceiling closure.
4 Do not use unit to support adjacent ceiling, light fixtures, etc.
5 Do not complete the ceiling below unit until electrical connections have been
completed and unit has been operated successfully.
6 Use slots on the projector plate and on the closure to adjust the unit to ensure proper
alignment of ceiling closure relative to ceiling opening.
WARNING
When using an electrical mounting system, basic precautions should always be followed,
including the following:
Please read the following installation guidelines thoroughly before using this mounting system.
Failure to do so may cause product to fall or otherwise fail, and could result in serious injury.
DANGER – To reduce the risk of electric shock:
1. Remove power before cleaning.
WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons.
2. Remove power before putting on or taking off parts.
3. Use this mounting system only for its intended use as described in these instructions.
Do not use attachments not recommended by the manufacturer.
4. If AeroLift mounting system is not working properly, call your dealer or Draper, Inc., [phone].
5. Never operate the mounting system with the air openings blocked.
6. Never drop or insert any object into any opening.
7. Do not use outdoors.
8. Installation and calibration of the unit should only be performed by an authorized, qualified,
and experienced professional. In particular, electrical work and wiring [indicated in diagram by
dashed lines] must be completed only by a qualified professional electrician who has read this
manual completely and is familiar with the construction and operation of this equipment and the
hazards involved.
9. Do not affix the unit to walls or ceilings that have inadequate strength to permanently hold the
unit during use. It is the owner’s and installer’s responsibility to confirm the wall or ceiling to
which the unit attaches is sufficient to permanently hold the weight and stress loads of the
unit at all times. Draper, Inc., is not responsible for improper installation, application, testing or
workmanship related to the product at place of installation.
10. It is the installer’s responsibility to make sure appropriate fasteners are used for mounting.
11. All hardware must be installed level. Unit must be level and square.
12. Never leave the area while operating the unit during installation, maintenance, or normal
operation, unless it is secure and safe.
13. Before testing or operation, carefully inspect the entire area and path (especially underneath) of
unit to be sure no persons or objects are in the area.
14. Turn off power and any nearby equipment or cables carrying electricity before connecting
switches, wires, controls, or electrical components.
15. Make sure the limit switches are pointed down or accessible when placing the motor in brackets.
16. All motors should be tested and limits set using test cord before unit is wired.
17. Do not wire motors in parallel without written permission from Draper, Inc.
18. During testing or operation, carefully watch the surrounding area for any potential safety
concerns including nearby persons or objects.
19. After installation, the entire system, including all sensors, should be carefully tested to ensure
safe and normal operation. Extreme care should be taken during testing to remain clear of
moving parts to avoid possible injury.
20. Operation of unit should be performed only by authorized and qualified personnel, who have
been trained in its safe and effective operation and understand its safety features.
21. The safety features of the unit should never be disabled, bypassed or overridden. The system
should not be operated until all safety features are properly and completely installed, calibrated
and tested.
22. Unit may need to comply with local, state or district rules and regulations, in particular when
installed in schools. All applicable rules and regulations should be reviewed before installation
and use.
23. Failure to precisely follow installation guidelines invalidates all warranties.
24. Custom products/installations may not be reflected in this manual. Call Draper, Inc., if you have
questions about the installation of custom products or any questions about your installation.
Before Beginning Installation
1. Look for any job site conditions that could interfere with installation or operation of the system.
2. Read carefully and be sure to understand all installation instructions and all related operations
manuals. These instructions are intended to serve as a guide for the installer and owner. They
should be followed closely and combined with the expertise of experienced qualified installers.
Draper, Inc., is not responsible for improper installation, application, testing or workmanship
related to the product at place of installation. Please retain all instructions for future use.
3. Open cartons lengthwise.
4. Locate and lay out all pieces.
5. Inspect all boxes to make sure you have received the proper unit and parts. Controls may be
shipped separately, or in same carton as unit .
6. If you have any difficulties with installing, servicing or operating your unit , call your dealer or
Draper, Inc., [phone].
Please Note: An appropriate disconnect device shall be provided as part of the building installation.
Aerolift must be installed in accordance with the requirements of Local Building Codes, Canadian Electrical Code (CEC), CAN/CSA C22.1 and National Electric Code (NEC), NFPA 70.
Improper installation and use of the AeroLift 35 Projector Lift can result in serious injury or death. Primarily, injuries can occur if the unit falls due to imprecise installation,
mishandling of the unit during installation or installation on an insufficient wall or ceiling structure. Please use extreme care.
101/8"
to
115/8"
193/8"
187/8"
11/4"
3
/4"
221/4"
121/2"
to
14"
Top ViewSide View
AeroLift 35
Relevant Mounting
Dimensions
page 2 of 8
AeroLift 35®

Section 2 - Installing Optional Environmental Air Space Housing
The Environmental Air Space Housing is shipped pre-assembled in its shortest position. Adjust height of housing by moving screws to different mounting holes in side panels.
Incremental adjustment for top screw and bottom screw is ½"; incremental adjustment for other screws is 1". Install the housing in a pre-assembled state or as separate components
(Requires housing be completely disassembled prior to installation).
Please note: If Environmental Air Space Housing is to be installed in a space with no access from above housing, it is recommended that the AeroLift 35 be installed
to upper section prior to installing housing. An access panel should then be installed.
1 Install top section using outer four holes
located on top of upper section. If installing
large housing, make sure to orient properly to
allow correct placement of lift within housing.
2 If installing large closure, attach brackets to
bottom of projector plate.
3 Attach AeroLift 35 to upper section of housing
through inner four holes in upper section with
provided
5
/ 16 " –18 x
7
/ 8 " hex head screws,
5
/ 16 "
flat washers and lock nuts. Lock nuts should be
used above housing (one per screw).
4 Attach the two flat panels of middle section
across from each other with the clinch nuts to
the outside of housing.
5 Attach the two middle section panels with
formed ends across from one another.
6 Attach lower section of housing.
Section 3 - Installing Projector
Draper’s optional Universal Projector Mount will hold up to
26 lbs.
See Installation Instructions included with Universal Pojector
Mount.
If not using Draper’s Universal Projector
Mount, generally the video projector
should be suspended from the bottom pan according to
projector manufacturer’s instructions.
If installing with a small closure, maximum projector size
is 18" x 8¾" (width x length x Environmental Air Space
Housing height).
If installing with a large closure, maximum projector size is
18" x 18" (width x length x Housing height).
The projector plate is not pre-drilled.
When drilling inital holes for mounting projector, or if for any
reason the hole placement must be changed, completely
lower AeroLift before attempting to drill holes. When
attaching projector bracket to plate, make sure screws are
short enough that they do not touch the motor/roller above
the plate when lift is closed.
Unit and projection system should be operated, checked
and adjusted as necessary at this time (see p. 5 for limit
adjustment procedures).
Warning: Keep fingers & other objects away from
ceiling closure when unit is operating. Serious injury
or damage can result.
10" (254mm)
5½"
(140mm)
10" (254mm)
5½"
(140mm)
7"
(178mm)
2½"
(64mm)
10" (254mm)
12" (305mm)
12" (305mm)
5½"
(140mm)
10" (254mm)
5½"
(140mm)
10" (254mm)
5½"
(140mm)
7"
(178mm)
2½"
(64mm)
10" (254mm)
12" (305mm)
12" (305mm)
5½"
(140mm)
A - Upper Section
B - Middle Section (Inside View)
C - Lower Section (Ceiling Trim Ring)
Environmental Air Space
Housing (collapsed)
page 3 of 8
AeroLift 35®

Section 5 - Wiring Diagrams
Section 4 - Electrical Connections
Unit operates on 110-120V AC, 60 Hz. current.
The AeroLift 35 ships closed, with a temporary field connection provided in the form of a pigtail temporarily wired to unit.
After hanging unit, make sure power is off, remove Jbox cover and temporarily connect the unit to power and to a switch, so unit can be lowered to allow access inside.
AeroLift must be installed in accordance with requirements of Local Building Codes, the Canadian Electrical Code (CEC), CAN/CSA C22.1 and the National Electric Code (NEC),
NFPA 70. All operating switches should be “off” before power is connected.
Please Note: Make sure electrical supply has been disconnected before attempting to connect AeroLift 35 to electricity.
Terminal strip for field connections is located inside a junction box on the end of the unit. Unit ships with internal lift wiring complete to terminal strip. Use switch to lower lift and
remove packing. Remove temporary wiring and complete permanent wiring to electricity and to switches. Wire to connect unit to power supply and to switches should be furnished by
installer. Connections should be made in accordance with wiring diagram. AeroLift 35 should be operated and checked prior to installing projector and/or optional ceiling closure.
Multi Station Control
BK
BL
LS2
LS1
LS2
LS1
BK
WH
BL
BK
OR
RD
12345 678TB
BK RD RD
BK
BL
RD
RD
BK
BK BK WH WH
GN/YL 14 AW
G
GN
RD 14 AWG
BK 14 AWG
WH 14 AWG
GN14 AW
G
BK 14 AWG
RD
PROJECTOR
OUTLET
MOTOR
BK
WH
L1 NGRD
BL
14 AWG
BL
BL
Location of key
operated On-off
switch if furnished.
Dashed Wiring
By electrician.
To 110-120 Vac Line
RD
COM
DOWNUP
COM
DOWNUP
COM
DOWNUP
IR Eye Input
Low Voltage
Tr igger
4-28 VDC
RS232/485
Inputs/Outputs
Receiver
Button 3 Button Wall Switch
DOWN - Black
COM - White
UP - Red
W
all Switch
Electrically Straight
Data Cable to more
LVC-IV modules*
*A maximum of six (6)
LVC-IV modules can
be linked together.
FUSE - 3.15 AMP
250 VAC 5x20mm
Dashed wiring by electrician
Low voltage wiring by others
Green/Yellow (Ground)
White -Common to Lift &
110V-120V AC Neutral
Yellow-to 110V-120V AC-Hot
Black-to 110V-120V AC-Hot
Brown-to LIFT(DOWN)
Red-to LIFT (UP)
12345 678L1NGND
To 110 -120V
AC Line
Key Operated On-Off
switch (if furnished).
AeroLift Terminal Block
UP
N N
DN COM
To 110-120 Vac Line
LS2
LS1
LS2
LS1
BK
WH
BL
BK
OR
RD
12345 678TB
BK RD RD BK BK WH WH
GN/YL 14 AWG
GN
RD 14 AWG
BK 14 AWG
WH 14 AWG
GN14 AW
G
BK 14 AWG
RD
PROJECTOR
OUTLET
MOTOR
BK
WH
L1 NGRD
UP DOWN
COMMON
SWITCH
BL
14 AWG
BL
Dashed Wiring
By electrician.
Single Station Control
Lift LVC - AeroLift Wiring Diagram
page 4 of 8
AeroLift 35®

Section 6 - Operation
When unit is first operated, be cautious! If unit fails to operate when the switch is flipped “down”, return switch to “off” and recheck electrical connections before proceeding. Cycle
unit down and up several times to confirm satisfactory operation.
Please Note: Optional 24V Control, Infrared or Radio Frequency Control, and RS 232/ ethernet require LVC-IV. (LVC-IV is optional, and does not come standard.)
Section 7 - Testing Safety Limit Switches
The AeroLift 35 is equipped with two Safety Limit Switches (see "Adjustments"). This switch may be damaged during shipping or by rough handling on the job site.
Once the AeroLift 35 has been installed in the ceiling, but before the projector and closure are attached, the Safety Limit must be tested. Use a screwdriver or other
tool to press and hold the switch. While holding down the switch, have someone operate the unit. If the unit works while the switch is depressed, the limit switch is
broken and must be replaced. Operating the unit without a functioning Safety Limit Switch could cause the unit's motor to continue operating after the lift is closed,
leading to a failure and the possibility of damage or injury.
Please Note: As weight is applied to the AeroLift 35, the projector plate may shift slightly. If this occurs, use setscrews on bottom of fabric roller
brackets to compensate for shift and level projector plate.
110-120V Single Station Control — 3-position up-off-down switch permits operation to be stopped at
any point. Factory adjusted limit switches automatically stop AeroLift 35 when fully down or fully up.
Optional 110-120V Multiple Station Control — Switches are similar in appearance to 110-120V Single
Station Control. AeroLift 35 stops when switch is released and may be restarted in either direction.
Factory adjusted limit switches automatically stop AeroLift 35 when up or fully down.
Optional 24V Control — Three-button up-stop-down switches stop at any point desired, operate in any
sequence. Factory adjusted limit switches automatically stop AeroLift 35 when fully up or fully down.
Optional Infrared or Radio Frequency Remote Control — If ordered, a three-button transmitter is
provided, with “up”, “down”, and “stop” buttons. Unit starts up or down when appropriate button
is pressed, and may be stopped by pressing “off” button. Factory set limit switches stop unit
automatically when projector is in “show” position.
Optional RS232/Ethernet— Serial communication and network communication optionally available with
wall switches, RF or IR remote.
Optional Key Operated Switching — Two kinds of key-operated switches available:
1 The key-operated power supply switch controls power to the AeroLift 35 and switches.
When it is “off”, the switches will not operate lift. Key may be removed from the switch
in either “on” or “off” position.
2 A three-position key switch permits the AeroLift 35 to be operated directly by key.
In this case, the screen’s operator must always have a key.
page 5 of 8
AeroLift 35®

Section 8 - Adjustments
CAUTION: Be sure all switches are in “off” position before adjusting limit
switches Always be prepared to shut lift off manually when new adjustment
is being tested.
Limit switches for the AeroLift are preset at the factory. The “Up” (closed) limit
switch is set for fully closed. The “down” (show) limit switch is set for fully lowered.
Once unit is in place, the “down” limit switch may need to be changed to stop the
AeroLift closer to the ceiling (that is, to raise the “down” position). Limit switches
are located on the end of roller, and are accessible by removing the cover of the
junction box at the left end of the unit. To adjust the limit switches, use a
5
/ 32 "
screwdriver/allen wrench.
Caution: It is not uncommon to overheat the motor during initial installation
when setting limits. The motor is thermally protected and will stop working
until it has cooled to a safe temperature before it will start operating again.
DO NOT physically pull the unit down when this occurs.
Adjusting “Down” (SHOW position) — “Down” position may be adjusted by turning
the DOWN limit switch adjustment socket. Turning the socket clockwise will stop
the AeroLift closer to the ceiling. Turning it counter-clockwise will cause the lift to
stop at a lower point.
Adjusting “Up” (CLOSED position) — Because the “up” (“closed”) position is
preset at the factory, Draper does not recommend changing this position
using the limit switch. The “up” position of the closure may be changed by
changing the length of threaded rod. If necessary, however, “up” position may
be adjusted by turning the UP limit switch adjustment socket. Turning the socket
counterclockwise creates a higher, or more fully closed position. Turning it
clockwise creates a lower ‘UP” (closed) position.
Caution: Make sure limit switch is set so that AeroLift motor is NOT still running
after lift is closed. If it continues to cycle once lift is closed, a failure may occur,
making unit descend rapidly and causing damage and/or injury.
Please Note: If load is off-center of pan, it may be necessary to adjust pitch of
fabric rollers. One setscrew is provided on each end of both fabric rollers
(see drawing). Use these to adjust roller pitch to keep entire fabric panel taut,
so load is evenly distributed. Use
1
/ 8 " hex key to adjust.
1
/
8
" Min. clearance
CAUTION: Make
sure there are
no obstructions
to operation
AeroLift Clearance
JUNCTION BOX
DOWN LIMITUP LIMIT
Fabric Roller Adjustment Setscrew
page 6 of 8
AeroLift 35®

If unit is equipped with a ceiling closure system, use either as is, or in conjunction with a piece
of existing ceiling tile.
Please refer to diagrams at right for instructions.
1 If installing with ceiling tile, it may be necessary to cut tile so overall dimensions are same
as (or slightly less than) closure panel. Place tile into trim frame. Lay closure panel on top
(back side) of ceiling tile, and tighten screws to hold in place.
2 If installing large closure, attach brackets to bottom of projector plate.
3 Attach
5
/ 16 " threaded rods to slots in projector plate or brackets.
Caution: Ensure bolts and nuts attaching brackets to AeroLift are
completely tightened.
4 Run unit “up” until bottom pan stops at highest position. Mark position on
5
/ 16 " rods
flush with ceiling level and cut rods to length (removing from pan if convenient).
5 Run unit “down” until bottom pan stops at “show” position.
6 Attach closure to lower end of
5
/ 16 " rods by slipping into four corner slots and secure
with nuts above and below slots.
7 Run unit “up” again to highest position. Measure distance by which panel fails to reach
required “closed” height for surrounding ceiling.
Caution: Make sure nuts are completely tightened.
8 Run unit “down” then re-adjust mounting of
5
/ 16 " rods in traveling grid to raise panel
required distance.
9 Test unit operation to confirm that panel will stop in closed position just before touching
ceiling.
Caution: DO NOT hang from, "ride," or pull down on unit. This could create a failure
and cause damage and/or injury.
PLEASE NOTE: Immediately upon completing surrounding ceiling, operate unit to
confirm that optional ceiling closure panel stops
1
/ 8 " short of ceiling in closed
position. If closure panel touches ceiling, motor may continue operating after lift is
closed. If it continues to cycle once lift is closed, a failure may occur, making unit
descend rapidly and cause damage and / or injury.
Section 9 - Installing Ceiling Closure
Large Closure
Brackets
Installing Optional Ceiling Trim Kit
1 Install AeroLift 35.
2 Install bottom section of housing in
opening by suspending with wire, or by
mounting directly to the ceiling joists (if
space permits).
3 Install projector and attach optional
ceiling closure.
Ceiling tile
(by others)
Lower section of
Environmental Air
Space Housing
Trim Ring
AeroLift 35
Standard Closure
AeroLift 35 with Large
Closure and Brackets
For Additional Safety:
1 Be sure the nuts that attach the threaded rods to the closure panel are tight.
2 Wrap a plastic wire tie around the mounting tab
and the threaded rod at all four corners of the
closure panel.
Please Note: Do NOT use a paper-covered
or similar wire tie—use only plastic
wire ties for maximum safety.
page 7 of 8
AeroLift 35®

Large Environmental Air Space Housing, Lift,
and Closure Dimensions
Small Environmental Air Space Housing, Lift,
and Closure Dimensions
Section 10 -Dimensions
Closure Panel 25"
EASH Mounting Holes 20 5/8"
Ceiling Trim Ring 23 7/8"
Ceiling Trim Ring 23 7/8"
Lipless Closure Dims: 22 1/8" x 22 1/8"
Closure
Panel
25"
Top View
Closure Panel 25"
22 5/8"
EASH 23 ½"
Between Rod
20 11/16"
22 5/8"
EASH 23 ½"
Ceiling Trim Ring 23 7/8"
12 5/8"
to
20 5/8"
EASH
EASH
Between Rod
20 11/16"
Trim
Ring
Closure
Panel
Closure Panel 25"
Ceiling Trim Ring 23 7/8"
Side Vie
wF
ront/Back View
Ø 3/8"
19 3/8"
10 1/8"
Lift
Mounting
Holes
EASH Mounting Holes 20 5/8"
Top View
Closure
Panel
15 5/8"
Ceiling Trim Ring 14
9
/
16
"
Ceiling Trim Ring 23 7/8"
EASH Mounting Holes 21¼"
Lift
Mounting
Holes
Ø 7/16" 4x
Closure Panel 25"
Closure Panel
15
5
/8"
EASH 14 ¼"
Ceiling Trim Ring
14 9/16"
13 3/16"
12 5/8"
to
20 5/8"
Closure Panel 25"
Between
Rod
9
9
/
16
”
Between Rod
20 11/16"
22 5/8"
EASH 23 ½"
Ceiling Trim Ring 23 7/8"
EASH
EASH
Trim
Ring
Closure
Panel
Front/Back ViewSide View
Lipless Closure Dims: 22 1/8" x 12 1/8"
19 3/8"
10 1/8”
EASH Mounting
Holes 8¾"
page 8 of 8
AeroLift 35®