DREAMS Charlie bed User manual

C h rl i e b
Two person
assembly
1 hour approx
assembly time
ed
a

Charlie Bed - Assembly Guide - Page 2

Charlie Bed - Assembly Guide - Page 3
Bed Bed Size Min Weight
(kg)
Max Weight
(kg)
Double 20 45
King 45
Superking 30 55
20
Charlie bed
DON' T LIFT WITHOUT MATTRESS ENSURE MATTRESS IS ON
BEFORE LIFTING
IMPORTANT OTTOMAN SAFETY WARNINGS
IMPORTANT – READ CAREFULLY – RETAIN FOR FUTURE REFERENCE
You must ensure that the mattress is on the bed frame before operating the
lift mechanism – Failure to do so could result in injury.
Keep hands clear of the mechanism when opening or closing the ottoman.
Beware ofentrapment – Never reach in through the mechanism to access
the storage area.
Always ensure that the ottoman is FULLY opened before accessing the
storage area.
Do not reach into the storage area through the hinge mechanism.
Do not exceed the maximum weight as specified in the table below:
Use caution when operating, always use the handle when lifting
Note: This bed uses a pressurised mechanism.
To be operated by adults only
Please ensure that children and pets are kept away from the bed when
operating the lift mechanism.
Keep children and pets away from the storage area.
No children or animals are left unattended when the frame is in the ’ up’
position.
Do not overload the internal storage base.
Do not stand inside the internal storage area of the bed
Before removing the mattress secure the frame to ensure it does not open
unexpectedly.
Do not attempt to lie on the mattress when the ottoman is in the raised
position.
When lifting the ottoman remove all bedding except the fitted sheet.
Depending on the weight of the mattress, the rising speed will vary so be
careful until you get used to the speed.
NOTE: When fully assembled and the mattress is in position, please raise and
lower the ottoman 4 / 5 times to ensure the gas pistons are fully lubricated.

Parts list
1. H ead board x 1
. Footboard x 1
. W ing s of head board x
Parts
. Feet x
2
. Right Side Rail x 1
. Left Side Rail x 1
. Support Wood x
. Baseboard x 1
. Centre Supporter x 1
. Slat frame x 1
. Mattress holder x
3
2
4
5
2
6
4
7
8
9
10
12
. Slat frame x 1
11
2
Charlie Bed - Assembly Guide - Page 4

Charlie Bed - Assembly Guide - Page 5
Screws (M x mm)
8 45
Screws (M x mm)
8 38
Washers (M x mm)
8 23 Spring Washers (M )
8Bolts (M x mm)
8 18
Allen Key (for M bolt)
8Bolts (M x mm)
8 60 Bolts (M x mm)
8 45 Bolts (M x mm)
8 25
Bolts (M x mm)
8 80
Felt Pads
Brack ets
Spanner (for M nut)
8
Nuts (M )
8
A x pcs
8B x pcs
34 C x pcs
4D x pcs
12
E x pc
1
M x pc
1
F x pcs
4G x pcs
14 H x pcs
12
K x pcs
4
J x pcs
8
I x pcs
6
N x pcs
4
L x pcs
12
Feet use only

17
A
A
1
Charlie Bed - Assembly Guide - Page 6
Step 2
Step 1Screws x (M x mm)
4 8 45
Attach x feet ( ) to the bottom of headboard (1)
27
with x screws mm (A) by using phillips head screwdriver (not provided).
4 45
A
Screws x (M x mm)
4 8 45
Attach x feet ( ) to the bottom of support wood ( ) with x screws mm (A)
2 7 6 4 45
by using phillips head screwdriver (not provided).
7
6
A

D
D
3
1
Charlie Bed - Assembly Guide - Page 7
Step 4
Step 3
Bolts x (M x mm)
18812
Install x bolts mm (D) to the holes in the headboard (1) and footboard ( ) as shown by hand.
12 18 3
Note: Do not tighten fully but leave mm gap as in the diagram.
10
BC
F
E
Allen Key x 1 (for M bolt)
8
Washers x (M x mm)
4 8 23
Bolts x (M x mm)
6084
Spring Washers x (M )
4 8
Attach x assembled feet ( ) to the footboard ( ) with x bolts mm (F),
2734 60
x washers (B) and x spring washers (C) by using allen k ey (E).
4 4
E
F
C
B
3
3

E
E
1
4
5
145
45 1
Charlie Bed - Assembly Guide - Page 8
Step 6
Step 5
Allen Key x 1 (for M bolt)
8
Attach side rails ( and ) to headboard (1) by Allen k ey (E) as shown.
4 5
BG
E
Allen Key x 1 (for M bolt)
8
Washers x (M x mm)
6 8 23 Bolts x (M x mm)
4586
Attach wings ( ) to the headboard (1)
2
with x washers (B) and x bolts mm (G)
6 6 45
by using allen k ey (E) as shown.
B
G
E
2
12
1
E
GB
1
2
2
4
5

1
3
4
5
3
4 5
3
E
Charlie Bed - Assembly Guide - Page 9
Step 8
Step 7
Allen Key x 1 (for M bolt)
8
Attach side rails ( and ) to footboard ( )
4 5 3
by Allen k ey (E) as shown.
E
4 5
HJI
Bolts x (M x mm)
25812 Brack ets x 6Felt Pad x 6
H
I
J
Attach x brack ets (I) to the headboard (1), side rails ( and ) and footboard ( ) with
64 5 3
x bolts mm (H) by using phillips head screwdriver (not provided).
12 25
Stick the felt pad (J) on each top of brack et (I).
1
3
4
5

Charlie Bed - Assembly Guide - Page 10
Step 10
Step 9
8
34545
3
8
3
4
5
Put the baseboard ( ) inside of bed. Attach the velcro to the four edges of frame.
8
Note: The two wings of baseboard should be attach to the support wood ( ) of footboard.
6
8
Pl eas e do n ot s tore i tems on s i de p an el s