DREAMS Kyoto TV Bed User manual

Assembly Instruction
Kyoto TV Bed
Min no. of people recommended to assemble this product.
Approx assembly time: 90 min
Helpful Advice
Please do not discard any of the packaging or instruction book until you have checked all the
components and fittings and the furniture is fully assembled. Keep all fittings out of reach of children.
In the unlikely event that this product has missing or damaged parts, please call customer service
on 08442 920000 to request spare or replacement parts.
1 of 6
Assemble all parts loosely until advised to tighten. Depending on use, it may be necessary to tighten the
fittings from time to time, so please save your allen key and spanner that has been provided.
Owing to the size and weight of the Kyoto TV Bed, we recommend that it is assembled by two adults,
on a flat surface, in the room that it is intended for.
Please do not use any tools other than those provided or recommeded in these instructions.

Headboard x 1
A x 18
M8 * 30mm
B x 20 C x 20 D x 4
E x 13 F x 1 G x 10
L x 1
K x 2
J x 6I x 6
H x 13
2 of 6
M5 * 50mm
17 * 8mm M4 * 15mm
M8 16 * 6mm
M6 * 16mm M6 * 45mm
M x 1
M6
O x 8 P x 1 Q x 2
M6 * 15mm
Note: The following fittings will be found in the box which contains the Sprung Slat Frame. Not with the bed frames
Assembly Kit.
1
4
23
7
10
5
8
11
6
9
Footboard x 1 Side Rail (Right) x 1
Side Rail (Left) x 1 Bottom Drawer Panel x 1 Side Drawer Panel (Left) x 1
Back Drawer Panel x 1
Power Lead x 1 Aerial Power x 1
Side Drawer Panel (Right) x 1 Support Drawer Leg x 2
Fittings
Parts
N x 4
M8 * 25mm

Assembly
3 of 6
02
E x 4
H x 4
Important:
Make sure when you fit the nuts
that the hole is in the correct
alignment.
A
23 & 4
FF
CC BB
7
E
7
8
6
H x 9
A
CB
FA
CB
F
13 & 4
C
B
N
C
B
N x 4 and A x 4
A x 8
01 A x 12 B x 16 C x 16 F x 1 N x 4
FF

Assembly
4 of 6
A x 4
B x 4
C x 4
F x 1
03
4
A
CB
F
A
CB
F
04
E
5
A x 2
F x 1
K x 2
E x 9
FF
A
A
K
9K
9

Assembly
5 of 6
10 x 1 11 x 1
D x 4 G x 4
GD
05
11
10
Aerial Socket
Power Socket
2
COMPLETE THE INSTALLATION OF THE TV
1. Connect the power and aerial cables to the socket at the bottom of the footboard, and leads to the wall socket.
10. When you want to watch TV again just press one of the TV lift buttons; your TV will rise from the footboard
and automatically turn back on.
2. Manually open the lid on the top of the footboard and carefully remove any transit packaging.
3. Raise the TV lift bracket by pressing one of the lift buttons located on either of the bed side rails.
4. Carefully unpack your TV.
5. Carefully remove the 4 x "VESA" screws from the back of the TV.
VESA screws are used as standard screws to fit to other type of wall mountings.
6. Connect the TV to the lift mechanism by adjusting the TV bracket located at the top of the TV lift by using the
screws (D) and washers (G) in your fixing back.
7. Connect the power, aerial and audio cables to the TV.
8. The TV can now be operated using the manufacturers instruction manual.
9. To lower your TV just press one of the TV lift buttons located on either of the side rails... your TV will
automatically turn off as it disappears into the footboard.
1. If your TV lift does not operate please check all power connections at the wall socket and into the base of
the footboard.
2. If your TV lift still does not operate please operate both TV lift buttons to see if one is not operating correctly.
If so check and replace the small battery located in the TV lift buttons that is not working. The lift button can
easily be removed from the side rail, and replace the battery located in the back of the button.
Battery type - CR2016
3. If your TV lift still fails to operate, after replacing the batteries, please contact customer service number for
further help and information.
TROUBLESHOOTING

J x 6
G x 6
M x 1
I x 6
Assembly
6 of 6
O x 8 P x 1 Q x 2
J x 4
G x 4 M x 1I x 4
MJ
G
I
x 6
IMPORTANT NOTE:
6(A). SOLID SLATS
6(B). SPRUNG SLAT SYSTEM
a) Your bedstead comes supplied as standard with Solid Wood Slats, or upgrade available to Sprung Slat System
at point of purchase at an additional cost.
b) Please carefully follow the correct assembly instructions for the slat system that you have purchased.
c) You have bought your bed, chosing one of two slat options; either solid or sprung. Although the assembly or
both options are explained here, only one option will apply to you.
MQ
OO
M
P
OO
MJ
G
I
x 4