Dunlop CBM95 Cry Baby Mini Wah User manual

THE ORIGINAL SINCE 1967.
®

CBM95CRY BABY® MINI WAH
DIAGRAM A
POWER
The Cry Baby®Mini Wah is powered by
one 9-volt battery (accessed via the bottom
of the pedal), an AC adapter such asthe
Dunlop ECB003/ECB003EU, or a DC
Brick™power supply.
SETUP INSTRUCTIONS
• Run a shielded instrument cable
from your guitar to the CBM95’s
INSTRUMENT jack.
• Run another shielded instrument cable
from the CBM95’s AMPLIFIER jack into
your amplifier input.
•Turnon the and begin playing.
•Toturn the pedal on/off, push the toe of
the pedal down until you feel a “click.”
• By rocking your foot back and forth
on the pedal, you can instantaneously
change the effect that the Cry Baby Wah
has on the tone of your instrument.
•Located under the rocker at the heel of
the pedal is an adjustable torque clutch.
Turn clockwise to increase resistance or
counterclockwise to decrease resistance
(Wrench included). See Diagram A
•Internal VOICING switch allows you
to change the frequency range of the
CBM95. To access, remove bottom
plate. Default setting is H—High, for
the standard GCB95 sound. For a more
vintage, midrange-focused sound, set
the switch to M. For a lower frequency
range, select L.
SAMPLE SETTINGS
GCB95
VINTAGE
LOW
SPECIFICATIONS
Impedance
Input 800 kΩ
Output 10 kΩ
Resonant Frequency
Heel Down 350 Hz - 450 Hz
Toe Down 1.5 kHz - 2.5 kHz
Maximum Level
Input -8.0 dBV
Output +10 dBV
Maximum Gain
Heel Down +19.5 dB
Toe Down +19.0 dB
Bypass True Hardwire
Noise Floor*
Heel Down -98 dBV
Toe Down -89 dBV
Current Draw 900 µA
*A-weighted, OdBV = 1VRMS

CBM95CRY BABY® MINI WAH
DIAGRAM A
POWER
The Cry Baby®Mini Wah is powered by
one 9-volt battery (accessed via the bottom
of the pedal), an AC adapter such asthe
Dunlop ECB003/ECB003EU, or a DC
Brick™power supply.
SETUP INSTRUCTIONS
• Run a shielded instrument cable
from your guitar to the CBM95’s
INSTRUMENT jack.
• Run another shielded instrument cable
from the CBM95’s AMPLIFIER jack into
your amplifier input.
•Turnon the and begin playing.
•Toturn the pedal on/off, push the toe of
the pedal down until you feel a “click.”
• By rocking your foot back and forth
on the pedal, you can instantaneously
change the effect that the Cry Baby Wah
has on the tone of your instrument.
•Located under the rocker at the heel of
the pedal is an adjustable torque clutch.
Turn clockwise to increase resistance or
counterclockwise to decrease resistance
(Wrench included). See Diagram A
•Internal VOICING switch allows you
to change the frequency range of the
CBM95. To access, remove bottom
plate. Default setting is H—High, for
the standard GCB95 sound. For a more
vintage, midrange-focused sound, set
the switch to M. For a lower frequency
range, select L.
SAMPLE SETTINGS
GCB95
VINTAGE
LOW
SPECIFICATIONS
Impedance
Input 800 kΩ
Output 10 kΩ
Resonant Frequency
Heel Down 350 Hz - 450 Hz
Toe Down 1.5 kHz - 2.5 kHz
Maximum Level
Input -8.0 dBV
Output +10 dBV
Maximum Gain
Heel Down +19.5 dB
Toe Down +19.0 dB
Bypass True Hardwire
Noise Floor*
Heel Down -98 dBV
Toe Down -89 dBV
Current Draw 900 µA
*A-weighted, OdBV = 1VRMS