EefaCo.Store 88 5536 951 User manual

PART LIST (in this carton)
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Tools Required For Assembly : Phillips screwdriver
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
88 5536 951
HARDWARE LIST
Casual Attire For Today's Home
Kitchen Cart
(Espresso Finish)
L.
Drawer
1 pc.
(
)
Drawer require assembly.
Please refer to the last page
of these assembly instructions.
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
A.
Top
1 pc.
D.
Back Rail
1 pc.
E.
Back Panel
2 pcs.
F.
Front Rail
1 pc.
G.
Shelf
1 pc.
H.
Base
1 pc.
J.
Door
1 pc.
K.
Door
1 pc.
Hex Wrench
1 pc.
Adjustable Pin
4 pcs. (+1 extra)
Caster
two lock
two non-lock
4 pcs.
Head Cap Bolt
8 pcs. (+1 extra)
Small
Hex Wrench
1 pc.
I.
Side Bar
2 pcs.
Machine Screw
4 pcs. (+1 extra)
Wood Screw
6 pcs. (+1 extra)
Wood Screw (Long)
8 pcs. (+1 extra)
Cam Lock Screw
2 pcs.(+1 extra)
Cam Lock
2 pcs.(+1 extra)

Assembly Instructions 2/4
IMPORTANT
Do not tighten screws until each part is properly assembled.
You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
Attach Top (A) to Side Panel (C) with Head Cap Bolts.
Attach Back Rail (D) to unit then slide Back Panels (E) into place.
STEP 2
S
C
SD E
S
E
Head Cap Bolt
A
S
B
C
Cam Lock Screw
Put Cam Lock Screws into the pre-drilled holes of Side Panel (B),(C) and tighten.
STEP 1

Assembly Instructions 3/4
STEP 3
Attach Base (H) to unit with
Head Cap Bolts.
Attach Front Rail (F)
to unit using Cam Lock.
Attach Side Panel (B)
to unit with Head Cap Bolts
and Cam Lock.
Attach the four Castors to
the pre drilled holes of legs
as shown.
BH
F
Locking Caster
STEP 4
Attach Side Bar to unit with
Machine Screws. (see Figure 1)
Attach Door (J) and (K) to
the side panels, by sliding
the door lift hinges into
the side panel hinges
(see Figure 2).
Insert Adjustable Pins
Into both side panels
at the desired level.
Slide Shelf (G) into place.
Slide Drawer (L) into position.
Head Cap Bolt
Adjustable Pin
L
JK
G
Machine Screw
Figure 2
Figure 1
I
I

Assembly Instructions 4/4
Figure 1
Figure 2
MAKE SURE ROLLER
IS ON THE BACK
L2
L2
L2
L3
L3
L3
L4
L4
L4
L5
L5
L1
L1
L1
Drawer (L)
Part List
L1.
Front Part
1 pc.
L5.
Base Part
1 pc.
L2.
Back Part
1 pc.
L3.
Side Part
1 pc.
L4.
Side Part
1 pc.
Attach L1 to L3 and L4, using
a and
wood screws ,
tighten halfway.
Attach L2 to L3 and L4 using
wood screws ,
tighten halfway. (see Figure 1)
Phillips screwdriver
(4X)
(4X)
long
long
Insert wood screws (6X)
into the pre-drilled holes in L5,
tighten screws. (see Figure 3)
short
Slide L5 into the grooves in L3
and L4. Be sure to push L5 all
the way forward so it meets L1.
(see Figure 2)
STEP 1
STEP 2
STEP 3
Tighten all screws used in
drawer assembly.
Figure 3