eka ekf 711 p User manual

USE AND INSTRUCTION MANUAL
USE AND INSTRUCTION MANUALUSE AND INSTRUCTION MANUAL
USE AND INSTRUCTION MANUAL
MOD
MODMOD
MODD
DD
D.
..
. E
EE
EKF
KF KF
KF 711
711711
711 P
PP
P –
––
– E
EE
EKF
KF KF
KF 664
664664
664 P
P P
P
rev.
rev.rev.
rev. 0
00
0
TECNOEKA S.r.l.
Via Mar o Polo, n.11 - 35010 Borgori o (Padova) Italy
Tel. [phone] Fax [phone]
www.te noeka. om E-mail: info@te noeka. om

TECNOEKA Srl ______________________________________________________________ use and instru tion manual
page 2 __________________________________________________________________________________________
CE
DECLARATION OF CONFORMITY
Annexed do ument II A, of dire tive 2006/42/EC
Annexed do ument II A, of dire tive 2006/42/ECAnnexed do ument II A, of dire tive 2006/42/EC
Annexed do ument II A, of dire tive 2006/42/EC
Manufa turer’s name TECNOEKA Srl
TECNOEKA SrlTECNOEKA Srl
TECNOEKA Srl
Manufa turer’s address Via
Via Via
Via Mar o Polo
Mar o PoloMar o Polo
Mar o Polo, 1
, 1, 1
, 11
11
1 -
--
- 3501
35013501
35010
00
0 Borgori o
Borgori oBorgori o
Borgori o (PD)
(PD)(PD)
(PD)
Manager’s name of te hni al file Minotto Lorenzo
Minotto LorenzoMinotto Lorenzo
Minotto Lorenzo
Manager’s address of te hni al file Via
Via Via
Via Mar o Polo
Mar o PoloMar o Polo
Mar o Polo, 1
, 1, 1
, 11
11
1 -
--
- 3501
35013501
35010
00
0 Borgori o
Borgori oBorgori o
Borgori o (PD)
(PD)(PD)
(PD)
Type of produ t Ele troni oven
Ele troni ovenEle troni oven
Ele troni oven
Purpose of the produ t Cooking food
Cooking foodCooking food
Cooking food
Model E
EE
EKF
KF KF
KF 7
77
711
11 11
11 P
PP
P –
––
– EKF 664
EKF 664 EKF 664
EKF 664 P
PP
P
TECNOEKA Srl de lares that the mentioned above produ ts meet the following safety
regulations:
Low voltage dire tive 2006/95/CE
Ele tromagneti ompatibility Dire tive 2004/108/CE.
TECNOEKA Srl de lares that the mentioned above produ ts meet the following harmonised
standards:
CEI EN 60335-1 ; CEI EN 60335-2-42
CEI EN 55014-1 ; CEI EN 61000-3-2 ; CEI EN 61000-3-3 ; CEI EN 62233
TECNOEKA Srl de lares that the mentioned above produ ts meet the following dire tives:
Ma hine Dire tive 2006/42/CE;
Dire tive on the general safety of produ ts 2001/95/CE;
Dire tive on the restri tion in the use of dangerous substan es in ele tri al and ele troni
applian es 2011/65/CE;
Dire tive on waste from ele tri al and ele troni applian es 2002/96/CE (RAEE).
TECNOEKA Srl de lares that the mentioned above produ ts meet the
CE 1907/2006 (REACH) Regulation
Borgori o, 26/02/2015. ________________________________
________________________________________________________________
________________________________
Signature of a Representative of the Board of dire tors
(CRISTINA LORA)
X:\Sgq\PRODOTTI\1 - FORNI\FORNO ELETTRICO\LEka\MANUALI D'USO - Forno Elettri o 40 60 90 -
LEka\Lingua Inglese\NUOVA GAMMA EF\Instru tion manual EKF 711 P - EKF 664 P - GB - rev. 0.do

Ele tri Oven rev. 0 _____________________________________________________________EKF 711 P – EKF 664 P
___________________________________________________________________________________________ page 3
Index
IndexIndex
Index
1.
Te hni al servi e
2.
General warnings
3.
Te hni al spe ifi ations
4.
Instru tions for the installer
5.
Use instru tions (for the user)
6.
Residual risks (for the user)
7.
How to use the ontrol panel
8.
Oven ooking
9.
Cleaning
10.
Maintenan e
11.
Te hni al servi e
12.
Information to the onsumers
13.
Wiring layout
14.
The Warranty

TECNOEKA Srl ______________________________________________________________ use and instru tion manual
page 4 __________________________________________________________________________________________
1
11
1.
. .
. Te hni al servi e
Te hni al servi eTe hni al servi e
Te hni al servi e
A te hni al he k-up on e or twi e a year helps prolong the life of the applian e and
guarantees better operation.
Make sure that assistan e is arried out solely and ex lusively by qualified personnel.
For any spare parts orders or for any information about the applian e, always mention the serial
number and model (data indi ated on the "te hni al data" plate at the rear of the oven).
2.
2. 2.
2. General warnings
General warningsGeneral warnings
General warnings
Very important!: keep this instru tion book together with the applian e for future onsultation.
These warnings were drafted for your safety and for that of others. Please read them arefully
before installing or using the applian e:
-If, on re eipt of the goods, the pa kaging
pa kagingpa kaging
pa kaging is damaged, write the following on the delivery
note: “I REVERSE THE RIGHT TO CONTROL THE GOODS
I REVERSE THE RIGHT TO CONTROL THE GOODSI REVERSE THE RIGHT TO CONTROL THE GOODS
I REVERSE THE RIGHT TO CONTROL THE GOODS”, spe ify the damage and get
the driver to sign in a eptan e; send a laim in writing to the seller within 4 alendar
days from the date of re eipt. No laim shall be a epted after su h period.
-The applian e is intended for professional use and must be utilised by qualified personnel
trained to use it.
-Any modifi ation whi h may be ne essary on the ele tri al system to enable installation
of the applian e, must be arried out solely by ompetent personnel.
-It is dangerous to modify or attempt to modify the hara teristi s of this applian e.
-Never lean the applian e with dire t water jets, be ause, if any water enters, it ould
limit the ma hine's safety .
-Before doing any maintenan e or leaning jobs, dis onne t the applian e from the
ele tri al mains and allow it to ool.
-Do not attempt to arry out the periodi ontrols or any repairs by yourself. Conta t the
nearest Servi e Centre and use only original spare parts.
N.B.:
N.B.:N.B.:
N.B.: Improper or in orre t use and failu
Improper or in orre t use and failuImproper or in orre t use and failu
Improper or in orre t use and failure to observe the installation instru tions shall release
re to observe the installation instru tions shall release re to observe the installation instru tions shall release
re to observe the installation instru tions shall release
the manufa ture from all responsibility.
the manufa ture from all responsibility.the manufa ture from all responsibility.
the manufa ture from all responsibility. In this onne tion, the dire tives in the "POSITIONING"
In this onne tion, the dire tives in the "POSITIONING" In this onne tion, the dire tives in the "POSITIONING"
In this onne tion, the dire tives in the "POSITIONING"
paragraph must be stri tly observed.
paragraph must be stri tly observed.paragraph must be stri tly observed.
paragraph must be stri tly observed.
3.
3. 3.
3. Te hni al spe ifi ations
Te hni al spe ifi ationsTe hni al spe ifi ations
Te hni al spe ifi ations
Dimensions of applian e LxDxH (mm)
Dimensions of applian e LxDxH (mm)Dimensions of applian e LxDxH (mm)
Dimensions of applian e LxDxH (mm)
935x930x825
Weight (Kg)
Weight (Kg)Weight (Kg)
Weight (Kg)
96,4
Conve tion heating element (kW)
Conve tion heating element (kW)Conve tion heating element (kW)
Conve tion heating element (kW)
4
(x2)
Max. absorbed power (kW)
Max. absorbed power (kW)Max. absorbed power (kW)
Max. absorbed power (kW)
8,4
Power supply voltage (V)
Power supply voltage (V)Power supply voltage (V)
Power supply voltage (V)
AC 400V 3N (50Hz)
Power able diameter
Power able diameterPower able diameter
Power able diameter
5x2,5 mm
2
Type of able
Type of ableType of able
Type of able
H07RN
-
F
Conne ting ele tri able
Conne ting ele tri ableConne ting ele tri able
Conne ting ele tri able
Tipo Y
Class
ClassClass
Class
I
Degree of
Degree ofDegree of
Degree of
prote tion against humidity
prote tion against humidityprote tion against humidity
prote tion against humidity
IPX3
The noise level of the applian e in operation is below 70 dB (A).
The noise level of the applian e in operation is below 70 dB (A).The noise level of the applian e in operation is below 70 dB (A).
The noise level of the applian e in operation is below 70 dB (A).
The "te hni al data" plate is positioned on the rear panel of the applian e.
The "te hni al data" plate is positioned on the rear panel of the applian e.The "te hni al data" plate is positioned on the rear panel of the applian e.
The "te hni al data" plate is positioned on the rear panel of the applian e.

Ele tri Oven rev. 0 _____________________________________________________________EKF 711 P – EKF 664 P
___________________________________________________________________________________________ page 5
4.
4. 4.
4. Instru tions for the installer
Instru tions for the installerInstru tions for the installer
Instru tions for the installer
The following instru tions are aimed at the qualified installer, to ensure that he arries out the
installation, adjustment and maintenan e operations as orre tly as possible and a ording to
urrent legal regulations. Any operation must be performed with ele tri al power ut to the
applian e. Before using the applian e, arefully remove the spe ial adhesive film prote ting the
parts in stainless steel. Do not leave any glue residues on the surfa es. If ne essary, remove
them at on e, with an appropriate solvent.
Positioning
PositioningPositioning
Positioning - Position the applian e perfe tly horizontally on a table or similar support (the table
or support must be at least 85 m above the floor). Position it at a distan e of not less than 10
m from the side and rear walls, to enable natural ventilating air to ir ulate freely around it.
The applian e is ventilated through spe ifi openings on the metal walls of the outer housing ,
and ensures effi ien y and long-life. For this reason it is stri tly forbidden to obstru t these
ventilation openings, even partially or for short periods. Failure to observe this spe ifi
Failure to observe this spe ifi Failure to observe this spe ifi
Failure to observe this spe ifi
prohibition releases the manufa turer of the applian e from all responsibility and immediately
prohibition releases the manufa turer of the applian e from all responsibility and immediately prohibition releases the manufa turer of the applian e from all responsibility and immediately
prohibition releases the manufa turer of the applian e from all responsibility and immediately
voids any guarantee rights for the said applian e,
voids any guarantee rights for the said applian e,voids any guarantee rights for the said applian e,
voids any guarantee rights for the said applian e, be ause its onstru tive onformity has been
voluntarily ompromised. Furthermore, the applian e is not suitable for embedding and for
grouped positioning with other identi al applian es.
Ele tri al onne tion
Ele tri al onne tionEle tri al onne tion
Ele tri al onne tion - The applian e must be onne ted to the ele tri al mains a ording to
urrent legal regulations. Before making the onne tion, make sure of the following:
-the voltage and frequen y values of the power supply system mat h the values on the
"te hni al data" plate affixed on the applian e;
-the limiting valve and the system are able to support the applian e's load (see the
"te hni al data" plate);
-the power supply system has an adequate earth onne tion a ording to urrent legal
the power supply system has an adequate earth onne tion a ording to urrent legal the power supply system has an adequate earth onne tion a ording to urrent legal
the power supply system has an adequate earth onne tion a ording to urrent legal
regulations;
regulations;regulations;
regulations;
-a omnipolar swit h with minimum between- onta ts aperture of the overvoltage
ategory III (4000 V), sized to the load and onforming to urrent legal regulations, is
fitted between the applian e and the mains in the dire t onne tion to the mains;
-the omnipolar swit h used for onne tion is easy to rea h when the applian e is
installed;
-the yellow/green e
the yellow/green ethe yellow/green e
the yellow/green earth wire is not interrupted by the swit h;
arth wire is not interrupted by the swit h;arth wire is not interrupted by the swit h;
arth wire is not interrupted by the swit h;
-the power supply, when the applian e is operating, must not deviate from the rated
voltage value by ±10%.
-make sure that after inserting the power supply ord into the terminal blo k it does not
ome into onta t with any of the ooking range's hot parts.
-if the supply able is damaged then it must be repla ed by the manufa turer or by your
if the supply able is damaged then it must be repla ed by the manufa turer or by your if the supply able is damaged then it must be repla ed by the manufa turer or by your
if the supply able is damaged then it must be repla ed by the manufa turer or by your
te hni al support or by a qualified person to avoid any risk
te hni al support or by a qualified person to avoid any riskte hni al support or by a qualified person to avoid any risk
te hni al support or by a qualified person to avoid any risk
Conne ting the power able
Conne ting the power ableConne ting the power able
Conne ting the power able - To rea h the power terminal board remove the left side of the
applian e. Loosen the able- lamp on the ba k (at the bottom) of the applian e and pass the
able through up to near to the terminal board. Lo ate the leads against the terminal board so
that the earth lead is the last to deta h from its terminal in the event of reverse pulling. Conne t
the 3 phase
phase phase
phase leads to the terminals marked “1” “2”
“1” “2”“1” “2”
“1” “2” and “3”
“3”“3”
“3”, the neutral
neutral neutral
neutral lead to the terminal
marked “4”
“4”“4”
“4” or “5”
“5”“5”
“5” and the earth
earth earth
earth lead to the terminal marked as shown in the following
layout:

TECNOEKA Srl ______________________________________________________________ use and instru tion manual
page 6 __________________________________________________________________________________________
(this ele tri al onne tion lay-out is lo ated near the power supply terminal board ). Tighten the
able gripper and re-fit the left side-panel of the applian e.
The applian e must be onne ted to an equipotential system
equipotential systemequipotential system
equipotential system whose effi ien y must first be
he ked a ording to urrent legal regulations.
This onne tion must be made between different applian es by using the appropriate terminal
marked with the symbol . The equipotential ondu tor must have a minimum diameter of 2,5
mm
2
The equipotential terminal is at the rear of the applian e.
Safety thermal breaker
Safety thermal breakerSafety thermal breaker
Safety thermal breaker - The applian e has a manually reset safety thermal breaker. It prote ts
against ex essive dangerous over-temperatures whi h ould be a identally generated inside the
applian e. If the devi e is tripped, it interrupts ele tri al power to the applian e and thus
prevents it from operating. To a ess this devi e, remove the left side-panel of the applian e.
5.
5. 5.
5. Use instru tions (for the user)
Use instru tions (for the user)Use instru tions (for the user)
Use instru tions (for the user)
This applian e is not intended for use by persons (in luding hildren) with redu ed phy al,
sensory or mental apabilities, or la k of experien e and knowledge. Unless they have
beengiven supervision or instru tion on erning use of applian e by a person responsible for
their safety. Children should be supervised to ensure that they do not play with the applian e.
For first use, we advise you to let the applian e to run load-free at maximum temperature for
about one hour. In this way, any unpleasant smells due to thermal insulation and residual work
grease are eliminated. This applian e must be used solely for the purpose for whi h it was
expressly designed, i.e. ooking foods in the oven. Any other use is onsidered unsuitable.
The applian e an be used: for all oven ooking of deserts, pizzas, meat, fish, vegetables, as
well as for gratinating, and for re- onditioning ooled and frozen foods. When pla ing food in
the ooking ompartment, leave a spa e of at least 40 mm between pans in order not to over-
obstru t air ir ulation. Do not use pans with higher than ne essary edges: edges are barriers
whi h prevent the ir ulation of hot air. Warm up the oven before every ooking operation to
obtain maximum uniformity. Do not salt foods in the ooking ompartment.
6.
6. 6.
6. Residual risks (for the
Residual risks (for the Residual risks (for the
Residual risks (for the user)
user)user)
user)
After a ooking operation, open the door autiously, to avoid a violent outflow of heat whi h
ould ause burns. While the oven is in operation, pay attention to the hot zones (marked on
the applian e) of its external surfa es. Pla e the ma hine on a ben h or similar support, at a
height of at least 85 m from the floor. The ben h or support must be able to support the
weight of the ma hine and house it orre tly. The applian e ontains ele tri al parts and must
never be washed with a jet of water or steam. The applian e is ele tri ally onne ted: before
attempting any leaning operation, ut power to the applian e. To prevent in orre t onne tion
of the applian e, the relevant ele tri al and water onne tions are marked by identifi ation
plates. If the internal glass panel of the door has to be leaned, it must be dismantled with the
help of a se ond operator: one operator supports the glass panel, while the other uns rews its
se uring s rews.

Ele tri Oven rev. 0 _____________________________________________________________EKF 711 P – EKF 664 P
___________________________________________________________________________________________ page 7
7.
7. 7.
7. How to use the ontrol panel
How to use the ontrol panelHow to use the ontrol panel
How to use the ontrol panel
1. "End of ooking" programming knob
2. Control thermostat knob
3. "End of ooking" programmer indi ator
light
4. Control thermostat indi ator light
1
2
3
4

TECNOEKA Srl ______________________________________________________________ use and instru tion manual
page 8 __________________________________________________________________________________________
Fig. 1 Fig. 2
Programming ooking time
Programming ooking timeProgramming ooking time
Programming ooking time - To run the oven, turn the programmer knob (Fig. 1) in line with
symbol ( ontinuous operation) or in line with the sele ted ooking time (up to 120 minutes).
In the se ond ase, end of ooking is signalled by the oven swit hing OFF automati ally.
Programming ooking temperature
Programming ooking temperatureProgramming ooking temperature
Programming ooking temperature - Turn the knob of the adjustment thermostat (Fig. 2) in line
with the temperature sele ted for ooking.
"End of ooking" programmer indi ator light
"End of ooking" programmer indi ator light"End of ooking" programmer indi ator light
"End of ooking" programmer indi ator light - The programmer green indi ator light indi ate
that the oven is operating and that ooking time is a tive.
Control thermostat indi ator ligh
Control thermostat indi ator lighControl thermostat indi ator ligh
Control thermostat indi ator light
tt
t - The ontrol thermostat orange indi ator light goes OFF
whenever the programmed temperature is rea hed inside the ooking ompartment. It lights up
again when the thermostat is tripped to re-establish this temperature.
Oven internal light
Oven internal lightOven internal light
Oven internal light - The light is always on when the oven is operating.
To swit h off the oven
To swit h off the ovenTo swit h off the oven
To swit h off the oven - Turn OFF the knobs of the "end of ooking" programmer and of the
thermostat. When you have finished using the oven, ut out ele tri power.
8.
8. 8.
8. Oven ooking
Oven ookingOven ooking
Oven ooking
For ooking, before putting food in, warm up the oven to the required temperature. When the
oven rea hes the temperature, put the food in and he k ooking time. Swit h off the oven 5
minutes before the theoreti al time in order to re over stored heat.
Conve tion ooking (dry heat)
Conve tion ooking (dry heat)Conve tion ooking (dry heat)
Conve tion ooking (dry heat) - Operate the oven and turn the thermo state knob to the
desired temperature.
De freezing
De freezingDe freezing
De freezing - Operate the oven and turn the thermo state knob and the humidifier knob in
orresponden e of position OFF (•).
9.
9. 9.
9. Cleaning (WARNING:
Cleaning (WARNING:Cleaning (WARNING:
Cleaning (WARNING: Cut power to the applian e before ev
Cut power to the applian e before evCut power to the applian e before ev
Cut power to the applian e before every operation)
ery operation)ery operation)
ery operation)
General leaning
General leaningGeneral leaning
General leaning - Clean the oven when it is old. Wash enamelled parts with lukewarm water
and soap, do not use abrasive produ ts, steel wool, or a ids, whi h ould ruin them. To lean
the steel parts, do not use produ ts ontaining hlorine (sodium hypo hlorite, hydro hlori a id,
et ) even if diluted. Use spe ifi off-the-shelf produ ts or a little hot vinegar. Rinse thoroughly
with water and dry with a soft loth. Clean the glass door of the oven with hot water only, and
do not use rough loths. Do not allow foods (espe ially a id foods su h as salt, vinegar, lemon,
et ) to stagnate on the stainless steel parts, be ause they ould deteriorate. Do not wash the
applian e with dire t jets of water, be ause if water enters, this ould limit the applian e's
safety. Do not use orrosive substan es (e.g. hydro hlori a id) to lean the oven' s support
ben h.
Cleaning the oven
Cleaning the ovenCleaning the oven
Cleaning the oven - It is good pra ti e to lean the oven interior at the end of every day of duty.
In this way it will be easier to remove ooking residues, preventing them from burning when the
oven is next used. Clean it a urately with hot water and soap or with the appropriate off-the-
shelf produ ts.

Ele tri Oven rev. 0 _____________________________________________________________EKF 711 P – EKF 664 P
___________________________________________________________________________________________ page 9
Cleaning the door
Cleaning the doorCleaning the door
Cleaning the door - The glass panel of the door fa ing inwards toward ooking ompartment
an be leaned with the same type of degreasing produ t used to lean the ompartment.
Otherwise, you an use normal glass leaning produ t (non toxi ). A ommon glass detergent
an be used also to lean the glass panel of the door fa ing outward. In all ases, you may just
use tepid soapy water. After rinsing, thoroughly dry the glass surfa e with a soft loth. If
opaque se tions form between the two glass panels of the door, they an be eliminated after
dismantling the internal glass panel.
Cleanin
CleaninCleanin
Cleaning the fans
g the fansg the fans
g the fans - The fans must be periodi ally leaned with spe ifi anti-lime s ale produ ts.
All the parts must be arefully leaned, removing all lime s ale deposits. To have a ess to the
fans remove the fan asing after removing the s rews that fix it to the ooking hamber. When
leaning is omplete, repla e the asing and s rews.
Cleaning the door seal
Cleaning the door sealCleaning the door seal
Cleaning the door seal - For hygiene and good operations, it is good pra ti e to lean the door
seal at the end of ea h day’s work. It should be arefully washed with warm soapy water, rinsed
and dried with a soft loth. Any in rustations or food deposits must be arefully removed,
without using sharp metal tools whi h ould irreparably damage the seal.
10.
10. 10.
10. Maintenan e
Maintenan eMaintenan e
Maintenan e
General information
General informationGeneral information
General information - A periodi ontrol (at least on e a year) of the applian e aids to guarantee
long life and orre t operations. Any sort of maintenan e work on the applian e must be done
ex lusively by te hni ally qualified operators who have been trained in the maintenan e work
on this applian e. Before beginning any sort of maintenan e work on the applian e, turn the
power supply off (at the magnetothermal safety swit h upstream from the applian e) and let it
ool down. A ess is gained to the inside omponents that ould require maintenan e work by
removing the left side of the applian e.
Changing the lighting lamp in the ooking hamber
Changing the lighting lamp in the ooking hamberChanging the lighting lamp in the ooking hamber
Changing the lighting lamp in the ooking hamber - The lamp is housed between the two
door glasses; to repla e it remove the internal glass as des ribed in the paragraph: “Cleaning
the door”. After removing the internal glass, repla e the lamp with another with the same
spe ifi ations: 12V 35W 300°C (this is a halogen lamp and should not be tou hed with your
bare hands).
Changing the door seal
Changing the door sealChanging the door seal
Changing the door seal - The door seal has a rigid profile with 3 fixing tabs. The profile must be
fitted into the guide on the fa e of the ooking hamber. The re tangular seal fits perfe tly into
the frame of the guide and, therefore, the seal profile fits perfe tly onto the fa e of the ooking
hamber. To hange the seal, remove the old one from the guide by pulling hard at the four
orners. Clean any dirt from the guide and introdu e the new seal (to make this operation
easier, we advise dampening the seal profile with soapy water).
Resetting the thermal breaker safety devi e
Resetting the thermal breaker safety devi eResetting the thermal breaker safety devi e
Resetting the thermal breaker safety devi e - This devi e is rea hed by removing the left side of
the applian e and an be reset by pressing the red key right down (whi h is marked by a spe ial
adhesive label), whi h is inside the ele tri omponents ompartment.

TECNOEKA Srl ______________________________________________________________ use and instru tion manual
page 10 __________________________________________________________________________________________
Possible faults
Possible faultsPossible faults
Possible faults
Type of fault
Type of faultType of fault
Type of fault
Cause
CauseCause
Cause
Corre tive a t
Corre tive a tCorre tive a t
Corre tive a t
ion
ionion
ion
Control panel
ompletely off (the oven
does not work)
-
In orre t ele tri onne tions to the
mains -Che k the mains onne tion
-
No mains voltage
-
Restore mains voltage
-Thermal break safety devi e tripped
-
Reset the thermal break safety
devi e
Cooking y le set: the
oven does not work
-Door open or ajar - Close the door
-Damaged magneti sensor
-
Conta t a qualified te hni ian to
repair the sensor
Door losed: steam
omes out of the seal
-
Seal not fitted orre tly
-
Che k the seal fitting
-Damaged seal
-
Conta
t a qualified te hni ian to
repair the seal
-Handle prong loosened
-
Conta t a qualified te hni ian to
repair the prong
The oven does not ook
evenly
-
One of the motors is blo ked or turns
slowly
-
Conta t a qualified te hni ian to
repair the motor
-The motors do not go into reverse
-
Conta t a qualified te hni ian to
repair the motor
-
Heating element not powered or is
damaged
-
Conta t a qualified te hni ian to
repair the element
Lighting lamp in the
ooking hamber does
not work
-
Damaged lamp
-
Change the lamp
-Damaged lamp feeder -
Conta t a qualified te hni ian to
repair the feeder
The thermo safety
devi e turns on in
ontinuous
-Devi e damaged
-
Conta t a qualified te hni ian to
repair the feeder
-Regulating thermo state damaged
-
Conta t a qualified te hni ian
to
repair the feeder
11. Te hni al servi e
11. Te hni al servi e11. Te hni al servi e
11. Te hni al servi e
Before leaving the fa tory, the applian e was ompletely regulated and tested by expert
spe ialised personnel to guarantee the best operating results.
All repairs and settings must be performed with utmost are and attention, respe ting national
safety regulations in for e. Always onta t your retailer or our nearest Servi e Centre, giving
details of the problem, the applian e model and the serial number (on the rating plate on the
rear panel). For any maintenan e the user an onta t Te noeka by alling the telephone
numbers on the over or going to www.te noeka. om
www.te noeka. omwww.te noeka. om
www.te noeka. om.
12.
12.12.
12. Informations to the onsumers
Informations to the onsumersInformations to the onsumers
Informations to the onsumers
Further to Dire tive 2002/96/EC, the symbol of the rossed rubbish skip on
the applian e means that at the end of its life, the produ t must be disposed
of separately from the other rubbish. The user must hand the applian e to a
spe ialised waste olle tion entre for ele tri and ele troni equipment.
The separate oll
e tion of the rubbish and subsequent treatment, re overy and disposal help to
produ e other equipment using re y led materials, redu ing the negative effe ts on the
environment and publi health, whi h would be aused by in orre t management of the
rubbish. Should the user dispose of the produ t abusively, administrative san tions would be
applied.

Ele tri Oven rev. 0 _____________________________________________________________EKF 711 P – EKF 664 P
___________________________________________________________________________________________ page 11
13.
13. 13.
13.
Wiring layout
Wiring layoutWiring layout
Wiring layout
Key
KeyKey
Key
M
Power terminal board
Pr "End of ooking" programmer
T1 Safety thermostat
T2 Oven thermostat
S1 Programmer indi ator light
S2 Thermostat indi ator light
IM Operating dire tion reversing element
C1-C2 Capa itors
MI
Door mi roswit h
B1-B2-B3-B4 Conta tor oil
B-R Conta tor Relais
T Transformer for oven lamp
L Oven lighting lamp
V1-V2 Radial motoventilators
V3 Tangential motorised ventilator
R1-R2 Cir ular heating elements

TECNOEKA Srl ______________________________________________________________ use and instru tion manual
page 12 __________________________________________________________________________________________
14.
14. 14.
14. The Warranty
The WarrantyThe Warranty
The Warranty
Your applian e is overed by warranty. The seller will repla e or repair (and his de ision will be final), free
of harge for the ustomer, only those parts that are defe tive due to a manufa turing fault on ondition
that, under penalty of forfeiture:
−for domesti equipment, the ustomer notifies the fault within two months from the date when
he/she dis overed it and anyway within 2 years form the date of pur hase;
−for professional equipment, the ustomer notifies the fault within 8 days from the date when
he/she dis overed it and anyway within 12 months from the date of pur hase,
by registered letter with a knowledgement of re eipt and en losing the invoi e or re eipt proving the
pur hase.
Apart from the ase when the ustomer annot produ e the invoi e or re eipt proving the pur hase or
when the above-mentioned terms are not omplied with, the warranty is expressly ex luded
warranty is expressly ex luded warranty is expressly ex luded
warranty is expressly ex luded in the
following ases:
1) faults or breakage aused by the transport;
2) wrong or in orre t installation of the produ t (for instan e be ause of insuffi ient draught of the
flue or exhausts) in light of the instru tions given in the user’s handbook supplied with the
produ t;
3) inadequate or abnormal ele tri al, hydrauli and/or gas supplies;
4) arelessness, negligen e or in ompeten e in using the produ t in light of the instru tions given in
the user’s handbook supplied with the produ t;
5) use of the produ t for uses different from the one for whi h it was built or anyway in a manner
not ompliant with the instru tions given in the user’s handbook supplied with the produ t;
6) tampering with the produ t;
7) adjustments and/or maintenan e and/or repairs arried out by unauthorised personnel and/or
with non original spare parts;
8) inadequate or areless maintenan e of the produ t in ontrast with the user’s handbook supplied
with the produ t;
9) damages aused by fire, natural disasters and a ident as well as by any ause not attributable to
TECNOEKA SRL.
The warranty expli itly ex ludes
The warranty expli itly ex ludesThe warranty expli itly ex ludes
The warranty expli itly ex ludes: varnished or enamelled parts, knobs, handles, movable or removable
plasti parts, bulbs, glass parts, refra tories and any a essories.
TECNOEKA SRL annot be held responsible for any damages, either dire t or indire t, aused by the
produ t breaking down or following its non-use.
Any repairs arried out during the warranty do not ause said warranty to be extended or renewed.
Nobody is authorised to modify the terms and onditions of the warranty or to issue new verbal or
written warranties.
The warranty is valid only for applian es installed in the European Union.
The warranty is valid only for applian es installed in the European Union.The warranty is valid only for applian es installed in the European Union.
The warranty is valid only for applian es installed in the European Union.
Any dispute shall be settled by the ompetent Court in Padua.
W
WW
Warning for the Buyer:
arning for the Buyer:arning for the Buyer:
arning for the Buyer:
1. the ooking applian e is designed only for ooking purposes while the heating applian e is
designed only for heating domesti environments;
2. TECNOEKA S.r.l. does not install the applian es; the seller shall be responsible for any installation
arried out;
3. TECNOEKA S.r.l. annot be held responsible for any damages, either dire t or indire t, to people,
pets or property aused by the applian e breaking down or following its non-use.
The Manufa turer annot be held responsible for any ina ura ies due to misprints or mistakes in
opying in this handbook. The Manufa turer reserves the right to modify the produ ts as he deems fit,
also in the interest of the user, without affe ting the vital hara teristi s of fun tionality and safety.