Elko iNels Air AirWD-101 Series User manual

1 / 3
AirWD-101
02-100/2017 Rev.: 0
7
1
4
5
5
3
+
-
2
8
9
6
10
2AirWD-101NB 1
5
Click!
3b
4
+
-
D/WD
ELKO EP, s.r.o.
Palackého 493
769 01 Holešov, Všetuly
Czech Republic
Tel.: [phone]
e-mail: [email protected]
www.elkoep.com
Characteristics Description
EN
General instrucions
Internet of Things (IoT)
• The IOT wireless communications category describes the Low Power Wide Area
(LPWA). This technology is designed to provide full-range coverage both inside and
outside buildings, energy-saving and low-cost operation of individual devices. Indi-
vidual networks - Sigfox, LoRa, NarrowBand - are available to use this standard.
Sigfox network information
• The network supports bidirectional communication but with a limited number of feed-
backs. It uses the free frequency band divided by Radio Frequency Zones (RCZ).
• RCZ1 (868 MHz) Europe, Oman, South Africa
• RCZ2 (902 MHz) North America
• RCZ3 (923 MHz) Japan
• RCZ4 (920 MHz) South America, Australia, New Zealand, Singapore, Taiwan
• Sigfox has more coverage across countries, so it is better suited for long distance moni-
toring.
• For more information on this technology, please visit www.sigfox.com.
LoRa network information
• The network is bidirectional and its communication uses free frequency band.
• 865 - 867 MHz India
• 867 - 869 MHz Europe
• 902 - 928 MHz North America, Japan, Korea
• The advantage of this network is the possibility of freely deploying individual stations
in local locations, thus strengthening their signal. It can therefore be used eciently in
company premises or, for example, in local parts of cities.
• For more information on this technology, please visit www.lora-alliance.org.
Information about the NarrowBand network
• The network provides two-way communication and the only one to use the licensed
LTE band. Our devices allow band 1 (2100MHz), Band 3 (1800MHz), Band 8 (900MHz),
Band 5 (850MHz), Band 20 (800MHz) and Band 28 (700MHz).
• It uses this SIM card technology for each device.
• The advantage of NarrowBand is the use of already built-up grids, which ensures suf-
cient reception outside and inside buildings.
• For more information on this technology, please visit www.vodafone.cz
Caution for proper operation:
• Products are installed according to the wiring diagram given for each product.
• For proper device functionality, it is necessary to have sucient coverage of the se-
lected network at the installation site.
• At the same time, the device must be registered in the network. Successful device reg-
istration on a given network requires a charge for trac.
• Each network oers dierent tari options - it always depends on the number of mes-
sages you want to send from your device. Information on these taris can be found in
the current version of the ELKO EP pricelist.
Magnetic detector (outdoor)
Made in Czech Republic
• The magnetic detector is used to detect motion – it is activated by attaching /
removing the magnet from the sensor.
• The Sigfox, LoRa or NB-IoT network can be used for message transmission.
• Data is sent to the server from which it can be subsequently displayed as a smart-
phone, application, or Cloud notication.
• Battery status information is sent as a message to the server.
• Anti-sabotage (tamper): If the device is tampered with, the message is immedi-
ately sent to the server.
• Power supply: 1x 3.6 V batteries SAFT with approx. 5 years (depending on the fre-
quency of use).
• Protection degree IP65.
Detector
Assembly
1. Using a at-blade screwdriver gradually slide it into one groove and the other in the lid
and swing open the cover.
2. Only with AirWD-101NB: Carefully insert nanoSIM (the device must not be energized
when inserting or replacing nanoSIM!)
3. The product can be attached in two ways:
a) Directly on a at surface by gluing * - apply a suitable adhesive to the bottom of the
base. Place the base in the desired location and let it dry.
b) Using a suitable fastener ** by screwing - drill holes into the base with two holes of
suitable diameter corresponding to the position of the holes in the bottom of the box.
Place the base at the desired location and attach it with suitable bonding material ac-
cording to the substrate.
1. Tamper
2. NanoSIM slot (AirWD-100NB
only)
3. Programming pins
4. Button SET
5. Mounting hole Ø 4.3 mm wall
6. Antenna
7. Magnetic contact
8. Battery
9. LED
10. Magnet
Cloud app assignment
It is done in your Smartphone application. Enter the relevant information on the product
cover into the application.
Function
• When the battery is inserted, the detector sends an initial message, the red LED blinks.
• Activation occurs when the magnet is attaching / removed from the sensor.
• The detector sends a data message every 12 hours. In case of a state change, it
sends the data message immediately.
• In case of an open box, every movement of the magnet in/out is indicated by the blink-
ing of the red LED. In the case of a weak battery when moving in / out of the magnet is
indicated by the LED flash twice.
Detector

2 / 3
AirWD-101S AirWD-101L AirWD-101NB
1 2 3 4 Click!
Recommendations for installation
• For the proper operation of the detector, the correct positioning position must be
maintained so that the sensing distance is maintained when the window or doors are
closed. Therefore, test the position of the detector and the magnetic module before
installation.
• WARNING: The detector has a magnet sensor located only on one side, so pay attention
to the correct position relative to the magnet.
• The detector is suitable for outdoor use. Operating conditions are consistent with con-
ventional chemically non-aggressive environments. The recommended working posi-
tion is vertical.
• Before fixing the detectors in place consult with the manufacturer of the windows and
doors, with regards to the most appropriate way to fix the detector.
• With the appropriate location (at the bottom of the window) can be applied to a win-
dow in a ventilation position.
• The product does not require special handling and maintenance.
• Ensure the correct location - see Warning.
* The glue must meet the optimal conditions for product placement (inuence of tem-
perature, humidity ...)
** For example, a screw or screw of max. Ø 4 mm can be used as a suitable fastener mate-
rial, 13 mm (distance to the partition in the box) must be added to the required length
for attachment to the substrate.
*** Suitable tting material can be, for example, a countersunk head screw, a screw Ø of
3 mm.
When handling a device unboxed it is important to avoid contact with
liquids. avoid unnecessary contact with the components of the device. Do
not touch the metal objects inside the unit.
Safe handling
Replacing batteries
1. Using a at-blade screwdriver gradually slide it into one and then the other groove in
the lid and swing open the cover.
2. Remove the discharged battery and insert a new battery into the holder. Beware of
polarity. Both LEDs will ash 3 times (see device status indication).
3. Replace and snap the front cover.
Notice:
Only use batteries designed for this product correctly inserted in the device! Immediately replace
weak batteries with new ones. Do not use new and used batteries together. If necessary, clean the
battery and contacts prior to using. Avoid the shorting of batteries! Do not dismantle batteries, do
not charge them and protect them from extreme heating - danger of leakage! Upon contact with acid,
immediately rinse the aected area with a stream of water and seek medical attention. Keep batteries
out of the reach of children. Batteries must be recycled or returned to an appropriate location (e.g.
collection container) in accordance with local legal provisions.
Technical parameters
* frekvenční pásma B1 / B3 / B5 / B8 / B20 / B28
** dle pokrytí jednotlivých sítí
*** pracovní teplota baterií je v rozsahu -60...+85 °C
**** součást balení
1x 3.6V LS 14500 Li-SOCl2AA
max. 5 years max. 3 years
0.2 mW
250 mW 150 mW 850 mW
Using a message from the server,
the programming cable
message to the server
message to the server
Button SET
Magnetic contact
Tamper
< 1.5 cm
> 2 cm
99.9 %
Reed magnetic contact
Sigfox LoRa NB-IoT
RCZ1 868 MHz 868 MHz LTE Cat NB1*
Approx 50 km** Approx 10 km** Approx 30 km**
25 mW / 14 dBm 25 mW / 14 dBm 200 mW / 23 dBm
-30... +60 °C (Pay attention to the operating
temperature of batteries)***
-30 .. +70°C
vertical
glue / screws
IP65
70 x 62 x 34 mm / 43 g (without battery)
15 x 75 x 13 mm / 13 g
Power supply
Battery power:
Battery life:
Standby consumption:
Transmitting power consumption:
Setting
Setting:
Alarm Detection:
Battery status view:
Control
Control:
Detection
Closed:
Open:
Reliability:
Sensor:
Communication
Protocol:
Transmitter frequency:
Range in open space:
Transmission power (max.):
Other parameters
Working temperature:
Storage temperature:
Operation position:
Mounting:
Protection degree:
Detector
Dimension / Weight:
Magnet D/WD****
Dimension / Weight:
Warning
Read the operating instructions before installing the device and putting it into opera-
tion. Instruction manual is designated for mounting and also for user of the device. It is
always a part of its packing. Installation and connection can be carried out only by a per-
son with adequate professional qualication upon understanding this instruction man-
ual and functions of the device, and while observing all valid regulations. Trouble-free
function of the device also depends on transportation, storing and handling. In case you
notice any sign of damage, deformation, malfunction or missing part, do not install this
device and return it to its seller. It is necessary to treat this product and its parts as elec-
tronic waste after its lifetime is terminated. Before starting installation, make sure that all
wires, connected parts or terminals are de-energized. While mounting and servicing ob-
serve safety regulations, norms, directives and professional, and export regulations for
working with electrical devices. Do not touch parts of the device that are energized – life
threat. To ensure the transmission of the radio signal, make sure that the devices in the
building where the installation is installed are correctly located. Unless otherwise stated,
the devices are not intended for installation in outdoor and damp areas, they must not
be installed in metal switchboards or in plastic cabinets with metal doors - this prevents
transmission of the radio frequency signal. iNELS Air is not recommended for control-
ling life-saving instruments or for controlling hazardous devices such as pumps, heaters
without thermostat, lifts, hoists, etc. - radio frequency transmission may be overshad-
owed by obstruction, interference, transmitter battery may be discharged etc., thereby
disabling the remote control.
4. Insert the battery and check the correct location (when the battery is inserted, the
detector functionality message will be sent to the application).
5. Replace and snap the front cover. When closing, the handles have to be snapped to their
original position.
1. Push a screwdriver into the hole in the upper part of the magnet, the top cover slide
and pull down magnet to open.
2. Break and remove the screw plugs (e.g. with a Screwdriver).
3. Place the base at the desired location (on the window or door frame) and attach it with
suitable bonding material according to the substrate.
4. Insert the top cover of the cover into the hole in the lower cover and snap it into place.
Magnet D/WD
You can attach the magnet in two ways:
• Directly on a at surface by gluing * - Apply a suitable adhesive to the outside of the
base. Place the base on the desired location (on the window or door frame) and let it dry.
• Using a suitable fastener *** by screwing.
Restart
• Open the cover. Power interruption (remove the battery from the device).
• Press SET> 1min.
• Connect power (insert battery). Close the cover.
(Depending on the type of sensing and
pulse frequency and transmission)

AirWD-101S AirWD-101L AirWD-101NB
3 / 3
power supply (external or battery), reset unit
start unit ok
opening the cover
non contact / contact magnet
test, cancel, „long press“
setting mode (signaling of measurement / pulses)
sending / receiving data
it is necessary to disconnect the power supply (external or battery), after 60 seconds after the LED goes out, insert the battery
the battery may be discharged
a discharged battery or a damaged product
Device states
x Search availability BTS
error MAC / error MODULU / error SIM
Unit initialization
Start
Search for BTS * 2)
SIM ERR *2)
ERR *2)
Successful network connection * 2)
Measurement
Tamper
Magnet
SET button short press (> 2s)
SET button longer press (> 2s / <5s)
Communication
Communication
Other known states
Does not respond to the SET button
The unit is still in reset
The unit does not respond even after
removal insert the battery
Indication
3 x R + G blinks
2 x ashes R (2xR _ 2xR _ ...)
5 x ashes R (repeatedly)
1 x ashes R
without indication
3 x ashes G
1 x ashes G
2 x ashes G
1 x ashes R
any LED lights
still indicates start
without indication
When the tamper is pressed, the LED is turned o!
Note:
R... LED red
G... LED green
* 1) Indicates only when you press SET> 2 s (setting mode)
* 2) Planned
Connection to the network
SIM Error - cannot be loaded (SIM
card insertion and rotation check) / or
NB-IoT MODULE error