emaux LED-P100 series Manual

WARNING
Never operate this Underwater Light for more than 10 seconds unless it is totally submerged
in water. Without total submersion, the light assembly will get extremely hot, which may result
in serious injury to pool users, installers, or bystanders, or in damage to property.
Be sure power is off before installing or removing lamp. Allow lamp to cool before relamping.
This light fixture uses a Halogen Quartz lamp. Do Not touch lamp with bare hand, this may
severely reduce its life. Use the plastic furnished with the replacement lamp to eliminate finger
prints from getting on lamp.
!
!
Operating Procedures
LED-P100 Series Underwater Light
1-44-4
REPLACEMENT PARTS
EMLI06081203
Description
Qty
Lens
Sealing o'ring
Screw
Face ring
Lens seal
Cover
1
1
1
1
3
8
Body
1
1
1
1
1
4
1Screw
Screw
1
1
2
Dent head
Item
1
2
3
4
5
6
7
Part No .
040102
040103
040105
040106
040104
040114
040119
8
9
10
11
13
12
040120
040111
040115
040112
040116
14
15
16
17
040113
040117
040121
040316
1 5
1 4
1 3
1 2
1 1
1 0
9
8
7
6
5
4
3
2
1
1 7
1 6
Bulb plate
020107 8Nut
Screw
Light Bracket
Wall Bracket
040317
Terminals insulation joints
Terminals insulation joints
2
Cable
PLEASE READ THE FOLLOWING CAREFULLY AND
KEEP THIS USER MANUAL SAVE FOR FUTURE REFERENCE
DANGER !
RISK OF ELECTRICAL SHOCK OR ELECTROCUTION
This underwater light fixture must be installed by a licensed or certified electrician or a qualified serviceman
in accordance to the requirements of your government standard or local authorities. Improper installation will
create electric hazards which could result in serious injury, death as well as damage to the property. Before
servicing the light,disconnect the power supply from the circuit breaker.Failure to do so could result in serious
injury, death and or damage to the property.

3-4
Figure 4.
4. After pool surface is finished, trim the Conduit.
5. Wrap a length of the cord up to a maximum of 2.4mt long on the back of the light assembly. This extra cord
allows you to bring the light out of the pool for relamping and servicing.
6. Connect cord electrical wires at Junction box, through Conduit, be careful not to pull the 75mm-80mm of slack cord
at the light through the conduit when connecting the wires.
7. Connect all wires to the corresponding circuit wires in the junction box and feed paraffin.
9. Before operating the light for more than 10 seconds fill pool until the Underwater Light is completely submerged in
water. To check for proper operation turn on main switch or circuit breaker as well as the switch that
operates the Underwater Light itself.
10.Rotating Locking System ensures light is secured to bracket, see Figure 4.
C. Winterizing: Light should be left in place for winterization.
8. Secure the junction box cover in place.
Figure 3.
Figure 2.
DO NOT MOUNT ON:
REVERSE RADIUS
SURFACE
IRREGULAR OR
UNEVEN SURFACES
DO MOUNT ON:
FLAT
SURFACE
WALLS WITH NO TIGHTER
THAN 6 FT. RADIUS AS
VIEWED FROM TOP
MOUNTING BRACKET
CONDUIT
LIGHT
X
OPEN
POSITION
LOCK
POSITION
2-4
120CM MIN.
WATER LEVEL
6.6CM
29.6CM
RIGID CONDUIT
TO POWER SOURCE;
FEED PARAFFIN
CONCRETE MUST BE CUT BACK
AROUND NICHE TO ALLOW FOR
A COMPACT PLASTER SEAL
45CM MIN. FROM WATER LINE
TO TOP OF LENS
A. Preparatory steps which must be completed by the electrician before light
is installed, see Figure 1.
INSTALLATION
Figure 1.
B. Perform the following steps after the electrical system requirements are met.
1. Locate position on a vertical wall where light is to be installed. The top of the light lens must be 45CM below
normal water level, see Figure 1.
2. Connect conduit to midst of Mounting Spacer (left of Bracket),see Figure 2.
3. If pool surface is to be plastered, you must allow proper concrete cutback for plaster thickness. Finish concrete
surface must be flush with Mounting Spacer. CAUTION: Finish area surrounding Mounting Spacer MUST be
flat and flush with the face of Mounting Spacer, this ensures a snug fit between light and wall, see Figure 3.
1. Ensure that the electrical system and its wiring for the pool conform to the requirements of your
govenment or your local authorities. The installation of the Underwater Light should only be performed
by a licensed electrician.
a. The junction box, or the low voltage transformer for 12 volt Underwater Light model is to be located at
least 120CM from the edge of the pool, see Figure 1.
b. The light fixture and all metal parts that are within 240CM of the pool must be properly protected with
non-ductile materials and that the connections must be waterproof.
c. The mounting bracket must be properly installed so that the top edge of the Underwater Light lens is at
least 45CM below the surface of the water in the pool, see Figure 1.
2. Consult the local Government Building Department to be certain that the pool's electrical system meets all
applicable requirements.