emaux S1000 User manual

1-4
Models: S1000 / S1200
EM FI 16 03 07 55
名 称
版 本 编 号
规 格
比 例
颜 色
产品负责人
更改日期
更改内容
零部件清单
版本 制图/设计
D
意万仕(中山)泳池设备有限公司
EMAUX ZhongShan)Swimming Pool Equipment Co., L t d(
审核 批准
80g印尼蓝
普通印刷
2016.03
1 : 1
420X297(mm)
EMFI16030755
PANTONE Process Black C
材 料
工 艺
日 期
EMAUX S1000-1200 沙缸 英文说明书
FUNCTION
The filter uses special filter sand to remove dirt particles from pool water. The filter sand is loaded into the
filter tank and functions as the permanent dirt removing media.When the control valve is in the FILTER
position, the pool water which contains suspended dirt particles, is pumped through your piping system
and is automatically directed by the patented filter control valve to the top of the filter tank.As the pool
water is pumped through the filter, dirt particles are trapped by the sand bed, and filtered out. The
cleaned Pool water is returned from the bottom of the filter tank,through the control valve and back to
the pool through the piping system. This entire sequence is continuous and automatic and provides for
total recirculation of pool water through your filter and piping System.
After a period of time the accumulated dirt in the filter causes a resistance to flow, and the flow diminishes.
Thismeans it is time to clean your filter. With the control valve in the BACKWASH position, the water flow is
automatically reversed through the filter so that it is directed to the bottom of the tank, up through the sand,
flushingthe previously trapped dirt and debris out the waste line. Once the filter is back-washed of dirt, set
control valve toRINSE position and run pump for about 1/2 to 1 minute, and then to filter, to resume normal
filtering.
NOTE: Turn pump off before changing valve position.
INSTALLATION
Only simple tools (screwdriver and wrenches), plus pipe sealant for plastic adapters, are required to install and
service the filter.
1) The filter should be placed on a level concrete slab, very firm ground, or equivalent. Position the filter so that
the piping connections, control valve are convenient and accessible for operation and service.
2) Loading the sand media. Filter sand media is loaded through the top opening of the filter.
a) Connect control valve to the filter using pipes with unions
b) Loosen the twelve nuts and washers and remove the filter coping.
c) We recommend filling tank approximately 1/3 way with water to provide a cushion effect when the filter
sand is poured in. This helps protect the under-drain laterals from excessive shock.
d) Carefully pour in correct amount and grade of filter sand. Sand surface should be leveled and should
come to about the middle of the filter tank.
and glues.(see the fig on page4).
4-4
WASTE
FILTER
BACKWASH RINSE
WASTE
RECIRCULATE
CLOSED
WASTE WASTE
WASTE WASTE WASTE
IN FLOW OUT FLOW IN FLOW OUT FLOW IN FLOW OUT FLOW
IN FLOW OUT FLOW IN FLOW OUT FLOW IN FLOW OUT FLOW
By-passes filter for circulating water to pool
Used after backwash to flush dirt from valve
Cleaning Filter by reversing the flow
By-passes filter, used for vacuuming to waste or lowering water level
CLOSED Shuts off all flow to filter or pool
RECIRCULATE
WASTE
RINSE
BACKWASH
FILTER
Valve Position
Normal Filtration and Vacuuming
Function
FUNCTIONS OF VALVE POSITIONS
THIS FILTER OPERATES UNDER HIGH PRESSURE. WHEN ANY PART OF THE CIRCULATING
PUMP, FILTER, VALVES, ETC.) IS SERVICED, AIR CAN ENTER THE SYSTEM AND BECOME PRESSURIZED .
PRESSURIZED AIR CAN CAUSE THE LID OR VALVE TO BE BLOWN OFF WHICH CAN RESULT IN SEVERE INJURY,
DEATH, OR PROPERTY DAMAGE.
TURN PUMP OFF BEFORE CHANGING VALVE POSITION.
TO PREVENT DAMAGE TO THE PUMP AND FOR PROPER OPERATION OF THE SYSTEM, CLEAN PUMP STRAINER
AND SKIMMER BASKETS REGULARLY.
DO NOT UNSCREW SCREWS OF FLANGE CLAMP WHILE PUMP IS RUNNING.
SYSTEM (e.g., CLAMP,
WARNING
GENERAL
1) Pipe tap boss provided for optional influent pressure gauge.
2) SERVICING VALVE( Stop pump,close gate valve in suction&discharge before proceeding):
a) Set handle in filter position. b) Remove cover screws. c) Lift cover and key assembly out.
TO ASSEMBLE:
1) Place valve key so that wedge opening is at TOP port (handle in Filter psn.). Flat edge of cover screw lug
should align with flat edge of body screw lug.
2) Position cover O'Ring.
3) Secure assembly to body with cover screws. Tighten cover screws evenly and alternately. Do not over-
tighten.

B
A
2-4
MAIN DIMENSION
3-4
3) Replace filter coping and tighten the nut. Take care, do not over-tighten.
4) Connect pump to control valve opening marked PUMP.
5) Make return to pool pipe connection to control valve opening marked RETURN and complete other
necessary plumbing connections, suction lines to pump, waste, etc.
6) Make electrical connections to pump per pump instructions.
7) To prevent water leakage, be sure all pipe connections are tight.
REPLACEMENT PARTS OF MULTIPORT VALVE
REPLACEMENT PARTS OF FILTER
1020
1220
2”
2”
Model A
High
mm
B
Diameter
mm
620
860
1220
1410
S1000
S1200
Valve Port
Size
Inch
Sand
Kg
DIMENSION TABLE
INSTALL/START-UP OF FILTER
1) Be sure correct amount of filter media sand is in tank and that all connections have been made and are
secure.
2) Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve
seal, always depress handle before turning.)
3) Prime and start pump according to pump instructions (be sure all suction and return lines are open),
allowing the filter tank to fill with water. Once water is flowing out of the waste line, run the pump for at
least 1 minute. The initial back-washing of the filter is recommended to remove any impurities or fine sand
particles in the sand media.
4) Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear,
about 1/2 to 1 minute.Turn pump off and set valve to FILTER position and restart pump.The filter is now
operating in the normal filter mode, filtering dirt particles from the pool water.
5) Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and
tighten connections, bolts, nuts, as required.
6) Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending
upon the pump and general piping system.) As the filter removes dirt and impurities from the pool water,
the accumulation in the filter will cause the pressure to rise and flow to diminish. When the pressure gauge
reading is 1.5 bar, higher than the initial "clean" pressure you noted, it is time to backwash the filter (see
BACKWASH under filter and control valve functions).
NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually
heavy initial dirt load in the water.
2
3
1
4
5
6
7
910 11 12
14
16
15 13
17
18
19
20
22
21
24
25
26
23
27
8
Key No.
Part No.
Product Description
Qty
1
01013003
Handle (Big)
1
2
03018008
Pin for Handle
1
3
01181027
Washer for Handle
1
4
01051026
2.0" Side Mount Valve Squareness Lid (White)
1
5
89280301
M6*32 Screw with Nut
10
6
01111048
Connector for Pressure Gauge/Stopper
1
02011139
O-Ring
1
7
89021303
Drain Plug with O'Ring
1
8
06011029
Oil Pressure Gauge With O-ring (40psi)
1
9
02020016
O-Ring for 2.0"Union
8
10
01051033
2.0" Connector(White)
3
11
01171154
2.0" Union (A/E)
3
12
01051032
2.0" Union Nut(White)
3
13
02011009
O-Ring for 2.0" Valve Lid
1
14
01181002
Washer for spring
1
15
02011022
O-Ring for 2.0" Valve Rotor
2
16
03014014
Spring
1
17
01021002
2.0" Valve Rotor
1
18
02311003
Spider Gasket
1
19
01051027
2.0" Side Mount Valve Bottom Body (White)
1
20
89280104
Sight Glass With O-Ring
1
21
02011011
O-Ring for Union Tale
1
22
01051035
2.0" Union Tale (White)
1
23
01013034
2.0" Union Nut (Black)
2
24
02020017
O-Ring for Plug
1
25
01051029
2.0" Side Mount Valve Plug (White)
2
26
01051195
2.0" Elbow Tube (White)183mm
1
27
01171035
2.0" Union Adaptor (Metric)
1
Key
No.
Part No.
Description
Qty
1
01111100
Star-Shaped Nut
1
2
03042001
Bow-Shaped Metal Bar
1
3
01161006
Manhole
1
4
02011155
O-Ring for Manhole
1
5
89011301
S1000 Filter Tank With Base
1
5
89011302
S1200 Filter Tank With Base
1
6
89011303
The Inner Tank System for 1000
1
6
89011304
The Inner Tank System for S1200
1
7
01101065
2.0" Tank System Support
1
8
89010613
Laterals (129mm & 185mm) for S1000
8
8
89010614
Laterals (129mm & 233mm) for S1200
8
9
01112038
32-40 inch Filter Base
1
9
01112039
Base for V1200
1
10
89010107
Water Drain Set
1
11
06011029
Maximum 40PSI Indication, Stainless Steel
Casing
1
12
02011127
O-Ring for Inlet & Outlet
2
13
88280813W
6 Way 2" Valve with Piping Kit, 2" union set
x 3 and pressure gauge (White)
1