Endress+Hauser Mycom S CLM 153 User manual

BA234C/07/en/12.02
51503794
Software version 1.20 or later
Mycom S
CLM 153
Conductivity Transmitter
Operating Instructions
MYCOM S CLM 153
ENDRESS+HAUSER
MEAS CAL
DIAG PARAM
?
Wahl
3.52
µS/cm
2
PS1
Select
Measure

First commissioning page 23 Mycom S CLM 153
2Endress+Hauser
First commissioning .................................... page 23
Using the menu "Quick Setup" in the chapter "First commissioning" you can configure
the transmitter with the most important parameters quickly and easily. Important basic
functions such as language, measured variable, temperature compensation and
current outputs are configured directly with the help of the on-site display.
You carry out further configuration in the corresponding menus as required.
Brief operating instructions
"PARAM": Parameter entry menu
"PARAM" allows you to return to the previous "return field" from any point in the menu.
"DIAG": brings you to the instrument diagnosis menu.
Help page: Press "DIAG" and "PARAM" together
"MEAS": Measuring mode
Press "MEAS" to exit any of the menus ("PARAM", "DIAG", "CAL") without having
completed the settings / calibration.
"CAL": Calibration
"E": (Enter): Continue in menu / confirm your selection
LED: "green" = everything OK. "red" = error.
Arrow keys:
• Scroll through items and highlight a selection or
• increment/decrement numbers by one step with "+" / "-".
Next digit: using the "right arrow" (editor type 1) or
• "Activate" with the "right arrow" and scroll through the selection with "+" / "-"
(editor type 2).

Mycom S CLM 153
Endress+Hauser 3
Table of Contents
1 Safety instructions . . . . . . . . . . . . . . . . . 4
1.1 Notes on safety conventions and icons . . . . . 4
1.2 Designated use . . . . . . . . . . . . . . . . . . . . . . . . 5
1.3 Installation, Commissioning, Operation . . . . . . 5
1.4 Operational safety . . . . . . . . . . . . . . . . . . . . . . 5
1.5 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 Identification . . . . . . . . . . . . . . . . . . . . . . 7
2.1 Device designation . . . . . . . . . . . . . . . . . . . . . 7
2.2 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . 8
2.3 Certificates and approvals . . . . . . . . . . . . . . . 8
3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1 Incoming acceptance, transport, storage . . . 9
3.2 Installation conditions . . . . . . . . . . . . . . . . . . . 9
3.3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.4 Post-installation check . . . . . . . . . . . . . . . . . . 11
4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.1 Quick wiring guide . . . . . . . . . . . . . . . . . . . . . 12
4.2 Connecting the measuring system . . . . . . . . 14
4.3 Post-connection check . . . . . . . . . . . . . . . . . 17
5 Operation . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.1 Display and operating elements . . . . . . . . . . 18
5.2 Replaceable memory . . . . . . . . . . . . . . . . . . 22
6 Commissioning . . . . . . . . . . . . . . . . . . . 23
6.1 Function check . . . . . . . . . . . . . . . . . . . . . . . 23
6.2 Switching on the measuring device . . . . . . . 23
6.3 Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.4 Description of functions . . . . . . . . . . . . . . . . . 30
7 Maintenance . . . . . . . . . . . . . . . . . . . . . . 83
7.1 Maintaining the measuring system . . . . . . . . . 83
8 Troubleshooting . . . . . . . . . . . . . . . . . 87
8.1 Troubleshooting instructions . . . . . . . . . . . . . 87
8.2 Response of outputs to errors . . . . . . . . . . . . 94
8.3 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . 94
8.4 Installation and removal of parts . . . . . . . . . . 96
8.5 Replacing the device fuses . . . . . . . . . . . . . . 97
8.6 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
9 Accessories . . . . . . . . . . . . . . . . . . . . . . . 98
10 Technical data . . . . . . . . . . . . . . . . . . . 101
10.1 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
10.2 Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
10.3 Performance characteristics . . . . . . . . . . . . . 103
10.4 Environment . . . . . . . . . . . . . . . . . . . . . . . . . 104
10.5 Mechanical construction . . . . . . . . . . . . . . . 104
11 Appendix . . . . . . . . . . . . . . . . . . . . . . . . 105
11.1 Operating matrix . . . . . . . . . . . . . . . . . . . . . 105

1 Safety instructions Mycom S CLM 153
4Endress+Hauser
1 Safety instructions
1.1 Notes on safety conventions and icons
General safety instructions
Electrical symbols
#
Warning!
This symbol alerts you to hazards which could cause serious injuries as well as damage to the instrument if
ignored.
"
Caution!
This symbol alerts you to possible faults which could arise from incorrect operation. They could cause
damage to the instrument if ignored.
!
Note!
This symbol indicates important items of information.
%
DC voltage
A terminal at which DC voltage is applied or through which DC flows.
&
AC voltage
A terminal at which (sine-form) AC voltage is applied or through which AC flows.
)
Ground connection
A grounded terminal, which, from the user’s point of view, is already grounded using a ground system.
*
Protective earth terminal
A terminal which must be grounded before other connections may be set up.
+
Equipotential connection
A connection which must be connected to the grounding system of the equipment. This can be, for example,
a potential matching line of a star-shaped grounding system, depending on national or company practice.
/
Double insulation
The equipment is protected with double insulation.
b
Alarm relay
Input
Output

Mycom S CLM 153 1 Safety instructions
Endress+Hauser 5
1.2 Designated use
The transmitter Mycom S CLM 153 is a device for measuring conductivity. The
transmitter is designed for measuring or control tasks in applications in the following
industries:
•Chemical process systems
•Pharmaceuticals
•Foodstuff industry
•Water treatment and monitoring
The Ex-version of the Mycom S CLM 153 makes operation in hazardous atmospheres
also possible (see "Certificates" in the product structure on page 7).
Any other use than the one described here compromises the safety of persons and the
entire measuring system and is, therefore, not permitted.
The manufacturer is not liable for damage caused by improper or non-designated use.
1.3 Installation, Commissioning, Operation
Please note the following items:
•Installation, electrical connection, commissioning, operation and maintenance of the
measuring system must only be carried out by trained technical personnel.
The technical personnel must be authorised for the specified activities by the system
operator.
•Technical personnel must have read and understood theses Operating Instructions
and must adhere to them.
•Before commissioning the entire measuring point, check all the connections for
correctness. Ensure that electrical cables and hose connections are not damaged.
•Do not operate damaged products and secure them against unintentional
commissioning.
•Measuring point faults may only be rectified by authorised and specially trained
personnel.
•If faults can not be rectified, the products must be moved from service and secured
against unintentional commissioning.
•Repairs not described in these Operating Instructions may only be carried out at the
manufacturer’s or by the Endress+Hauser service organisation.
1.4 Operational safety
#
Warning!
If the device is used for any application other than those described in these Operating
Instructions, it may lead to unsafe and improper functioning of the measuring system
and is therefore not permitted.
The instrument has been designed and tested according to the state of the art and left
the factory in perfect functioning order. The instrument meets all the prevailing
regulations and EC directives - see "Technical data".
However, always pay attention to the following points:
•Measuring systems used in Ex areas have a separate document (XA 233C/07/a3)
which forms a component part of these Operating Instructions. Always follow the
installation regulations and the - partly deviating - connection data of the Ex documen-
tation as well. You can find the following symbols on the front page of the additional

1 Safety instructions Mycom S CLM 153
6Endress+Hauser
Ex documentation (according to approval and test centre
(
0 Europe, 2 USA, 1 Canada).
•The measuring device complies with the general safety requirements in accordance
with EN 61010, the EMC requirements of EN 61326, and NAMUR Recommendation
NE 21, 1998.
•The manufacturer reserves the right to change the technical data in line with technical
progress at any time. You can obtain information on the current version of these
Operating Instructions and possible additions from your E+H sales centre.
1.4.1 Immunity to interference
This instrument has been tested for electromagnetic compatibility in industrial use
according to applicable European standards. It is protected against electromagnetic
interference by the following design measures:
•cable screening
•interference suppression filter
•interference suppression capacitors
#
Warning!
Protection against interference as specified above is valid only for an instrument
connected according to the instructions in these Operating Instructions.
1.5 Return
If the transmitter has to be repaired, please return it cleaned to the E+H sales centre
responsible. You can find the address on the last page of these instructions. For returns
please use the original packaging.
With the instrument, please enclose a completed copy of the "Declaration of
Contamination" form. You can find this at the end of these Operating Instructions.

Mycom S CLM 153 2 Identification
Endress+Hauser 7
2 Identification
2.1 Device designation
2.1.1 Product structure
Conductivity transmitter in aluminium housing for wall mounting with one alarm and two
output contacts for NAMUR, ChemoClean and controller functions as well as three
binary inputs, logbooks, data loggers, USP limit functions. Plain text operation.
247x167x111 mm (HxWxD). Degree of protection IP 65.
Certificates
A Basic equipment: non-Ex
G With Atex approval, Atex II (1) 2G EEx em ib[ia] IIC T4
O With FM approval; NI Cl. I, Div. 2, Sensor IS Cl. I, Div. 1
P With FM approval; NI Cl. I, Div. 2
S With CSA approval; NI Cl. I, Div. 2, Sensor IS Cl. I, Div. 1
T With TIIS approval
Measuring input
1 1 measuring circuit for conductive sensors, conductivity/resistance and temperature
2 1 measuring circuit for inductive sensors, conductivity/resistance and temperature
3 2 measuring circuits for conductive sensors, conductivity/resistance and temperature
4 2 measuring circuits for inductive sensors, conductivity/resistance and temperature
Measuring output
A 2 current outputs 0/4 ... 20 mA, passive (Ex and non-Ex)
B 2 current outputs 0/4 ... 20 mA, active (non-Ex)
C HART with 2 current outputs 0/4 ... 20 mA, passive (Ex and non-Ex)
D HART with 2 current outputs 0/4 ... 20 mA, active (non-Ex)
E PROFIBUS-PA, without current outputs
Contacts, current input
0 Without additional contacts
1 3 additional contacts
2 2 additional contacts, 1 passive current input (Ex and non-Ex)
3 2 additional contacts, 1 resistance input (non-Ex)
4 1 additional contact, 2 passive current inputs (Ex and non-Ex)
5 1 additional contact, 1 passive current input, 1 active resistance input (non-Ex)
Power supply
0 100 ... 230 V AC
8 24 V AC / DC
Language versions
A E / D
B E / F
C E / I
D E / ES
E E / NL
F E / J
Cable connection
0 Cable glands M 20 x 1.5
1 Adapter for cable gland NPT ½"
2 Adapter for cable gland G ½
Additional equipment
0 Without additional equipment
1 Additional equipment: DAT module
Configuration
0 Factory settings
CLM 153- Complete order code

2 Identification Mycom S CLM 153
8Endress+Hauser
2.1.2 Nameplate
2.2 Scope of delivery
The scope of delivery comprises:
•Instrument type and version acc. to the nameplate (s. chap. 2.1.2)
•Operating Instructions BA 234C/07/en (for Ex-system also the XA 233C/07/a3)
2.3 Certificates and approvals
Declaration of conformity
The product meets the legal requirements of the harmonised European standards.
Endress+Hauser confirms compliance with the standards by affixing the
4 symbol.
Fig. 1: Example of a nameplate for the transmitter Mycom S CLM 153.

Mycom S CLM 153 3 Installation
Endress+Hauser 9
3Installation
3.1 Incoming acceptance, transport, storage
•Make sure the packaging is undamaged!
Inform the deliverer about damage to the packaging.
Keep the damaged packaging until the matter has been clarified.
•Make sure the contents are undamaged!
Inform the deliverer about damage to the delivery contents.
Keep the damaged products until the matter has been clarified.
•Use the delivery papers and your order to check that the scope of delivery is
complete.
•For storage and transport purposes, pack the instrument so that it is protected against
impacts and humidity. The original packaging offers the best protection. Also, keep to
the approved ambient conditions (see "Technical data").
•If you have any questions, please contact your supplier or your nearest
Endress+Hauser sales centre, (see the back page of these Operating Instructions).
3.2 Installation conditions
3.2.1 Dimensions
You can find the dimensions and lengths of the transmitter in the Technical data on
page 101 ff.
3.3 Installation
3.3.1 Installation instructions
•The standard use of the Mycom S CLM 153 transmitter is as a field instrument.
•The Mycom S CLM 153 transmitter can be fixed to vertical or horizontal pipes using
the round post fixture available from Endress+Hauser (see Accessories). When
installing the instrument outdoors, you also require the weather protection cover
CYY 101. This cover is compatible with all field instrument installations options.
•Always install the transmitter so that the cable entries point downwards.
•The transmitter can be installed as a panel-mounted unit as well.
3.3.2 Wall mounting
"
Caution!
•Check that the temperature does not exceed the maximum permitted ambient
temperature (–20°... +60°C). Install the instrument in a shady location. Avoid direct
sunlight.
•Mount the wall mounting housing so that the cable entries always point downwards.

3 Installation Mycom S CLM 153
10 Endress+Hauser
Fig. 2: Dimensions for wall mounting: Fixing screw: dia. 6 mm
Wall plug: dia. 8 mm
1: Fixing drillholes
2: Plastic cover caps
For the wall mounting of the transmitter proceed as follows:
1. Prepare drill holes acc. to fig. 2
2. Push the two fixing screws from the front through the appropriate fixing bores ➀.
–Fixing screws (M6): max. dia. 6.5 mm
–Screw head: max. dia. 10.5 mm
3. Mount the transmitter housing on the wall as shown.
4. Cover the drill holes with the plastic cover caps ➁.
3.3.3 Post mounting and panel mounting
Mount the parts of the mounting kit (see
accompanying figure) at the back of the
housing as depicted in fig. 4.
Required mounting cutout for panel
mounting: 161 x 241 mm
Installation depth: 134 mm
Pipe diameter: max. 70 mm.
Fig. 3: Mounting kit Mycom S CLM 153
154
100
247
142
167
∅8
2
C07-CPM153xx-11-00-08-xx-001.EPS
1