Bradley SXWS9148FM User manual

215-1360 Rev. G; ECN 13-10-005
© 2013 Bradley
Page 1 of 3 3/1/2013
P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 800.BRADLEY (800.272.3539) FAX [phone]
bradleycorp.com
Installation
IMPORTANT!
Read this entire installation manual to ensure proper installation. When
finished with the installation, file this manual with the owner or maintenance
department. Compliance and conformity to local codes and ordinances is
the responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for
before discarding packaging material. If any parts are missing, do not begin
installation until you obtain the missing parts.
Make sure that all water supply lines have been flushed and then completely
turned off before beginning installation. Debris in supply lines can cause
valves to malfunction.
Product warranties may be found under “Products” on our web site at
bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List
•
•
•
•
Front-Mounted Two-Head
SX Panel Shower
SXWS9148FM
Ligature Resistant
Front-Mounted
Two-Head SX Panel Shower
HSC91
Rough-in Dimensions ............................................ 2
Installation ............................................................. 3
Caring for Stainless Steel...................................... 3
SXWS9148FM with "SX" severe
service showerheads shown

SXWS9148FM, HSC91 Installation
23/1/2013 Bradley • 215-1360 Rev. G; ECN 13-10-005
Dimensional Information
Installation
(mm)
42-5/8"
(1083)
24"
(610)
13"
(330)
44"
(1118)
11-5/8"
(295)
33-1/8" (841)
to Finished Floor
72" (1828)
to Finished Floor 42" (1064)
to Finished Floor
SXWS9148FM shown.
Rough-ins same for HSC91.
Wall Opening
AUsing the hex key (taped to the shower
panel), remove the ten security screws
from the shower panel and remove the
frame from the panel.
BInstall the frame into the wall
opening per the instructions
included with the frame.
EReattach the panel to the frame
with the ten security screws.
C
Install the control buttons per
instructions included with the
valve assembly. Apply 100%
silicone caulk to escutcheon
backside prior to installation
to ensure a water tight seal.
Wipe excess caulk from
front side of escutcheon and
panel.
D
Install the valve assembly and make the
valve connections to the showerhead
and control buttons per the instructions
included with the valve assembly.
Minimum Wall Depth:
Frame Only = 2.0" (51)
ASTM = 4-1/2" (114)
TTST=3.0" (76)
WARNING! After installation, all joints require security
sealant by installer to eliminate gaps (if present)
between wall and fixture.
FEnsure proper shower head
adjustment and tightening of
screws.

Installation SXWS9148FM, HSC91
Bradley • 215-1360 Rev. G; ECN 13-10-005 3/1/2013 3
Cleaning Stainless Steel
Material Description: Stainless steel is extremely durable, and maintenance is simple and inexpensive. Proper care, particularly
under corrosive conditions, is essential. Always start with the simplest solution and work your way toward the more complicated.
Routine cleaning: Daily or as often as needed use a solution of warm water and soap, detergent, or ammonia. Apply the cleaning
solution per the manufactures instructions and always use a soft cloth or sponge to avoid damaging the finish.
Stubborn Stains: To remove stains from stainless steel use a stainless steel cleaner and polish such as Ball® stainless steel
cleaner or a soft abrasive. Always follow the manufactures instructions and apply in the same direction as the polish lines.
Special Situations for Material
Fingerprints and Smears: To remove fingerprints or smears use a high quality stainless steel cleaner and polish in accordance with
the manufactures instructions. Many of these products leave a protective coating the helps prevent future smears and fingerprints.
Grease and Oil: To remove grease and oil use a quality commercial detergent or caustic cleaner. Apply in accordance to the
manufactures instructions and in the direction of the polish lines.
Precautions: Avoid prolonged contact with chlorides (bleaches, salts), bromides (sanitizing agents), thiocyanates (pesticides,
photography chemicals, and some foods), and iodides on stainless steel equipment, especially if acid conditions exist.
The appearance of rust streaks on stainless steel leads to the belief that the stainless steel is rusting. Look for the actual source of
the rust in some iron or steel particles which may be touching, but not actually a part of the stainless steel structure.
Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an endorsement, nor
does the omission of any brand name cleaner imply its inadequacy. Many products named are regional in distribution, and can be
found in local supermarkets, department and hardware stores, or through your cleaning service. It is emphasized that all products
should be used in strict accordance with package instructions.
Never use ordinary steel wool or steel brushes on stainless steel.
Always use stainless steel wool or stainless steel brushes.
Do not permit salty solutions to dry and evaporate on stainless steel.
Strongly acidic or caustic cleaners may attack the steel causing a
reddish film to appear. The use of these cleaners should be avoided.