Enwork Ligouri TI0061 User manual

Ligouri
06/17/21 - Rev A
Touchdown Table
Installation Instructions
TI0061

1) Parts and Fasteners Included
INSTALLATION GUIDE
Corner Leg Assembly (4x) Tube for Depth (2x)
LNA-2003-x
Mid-Leg Assembly (0x, 2x, or
4x)
Tube for Width (2x, 4x, or 6x)
LNA-2003-x
3/8-16 x 0.75 Button Head
Socket Cap Screw (16x, 24x,
or 32x)
#8 x 0.75 Pan Head Phillips
Wood Screw
1
Zipbolt Tight Joint (4x)

2) Tools and Supplies Required
INSTALLATION GUIDE
Drill #2 Phillips Drive Bit
(magnetic tip preferred) 7/32” Hex Bit Socket or Allen
Key
LevelTape Measure
2

3) Assembly:
INSTALLATION GUIDE
One-Piece Table (Pages 4-5)
Overview
3
Multi-Piece Table (Pages 6-8)

4) Assembly:
INSTALLATION GUIDE
1. Attach the Corner Leg Assemblies to a Tube (depth)
using the 3/8-16 x 0.75 Button Head Socket Cap
Screws. Keep small holes in Tube facing upwards.
Note: Finger tighten for now.
2. Attach the end assemblies from Figure 4.1 to the
Tubes (width) using the 3/8-16 x 0.75 Button Head
Socket Cap Screws. Keep small holes in Tube facing
upwards.
Note: Finger tighten for now.
3. Fully tighten all the 3/8-16 x 0.75 Button Head
Socket Cap Screws.
One-Piece Table
Figure 4.1
Figure 4.2
Figure 4.3
4
2x

4) Assembly:
INSTALLATION GUIDE
4. On a non-marring surface, center the assembled
base on the Top and attach using the #8 x 0.75 Pan
Head Phillips Wood Screws.
Note: Screws go through clearance holes in bottom of
the Tube.
5. With the Table flipped in the upright position, level
the Table using the glides in the bottom of each leg.
One-Piece Table
Figure 4.4
Figure 4.5
5

5) Assembly:
INSTALLATION GUIDE
Figure 5.1
Figure 5.2
Figure 5.3
1. Attach the Corner Leg Assemblies to a Tube (depth)
using the 3/8-16 x 0.75 Button Head Socket Cap
Screws. Keep small holes in Tube facing upwards.
Note: Finger tighten for now.
2. Attach Tubes (width) to the Mid Leg Assembly using
the 3/8-16 x 0.75 Button Head Socket Cap Screws.
Keep small holes in Tube facing upwards.
Note: Finger tighten for now.
3. Attach the end assemblies from Figure 5.1 to the
Tubes (width) using the 3/8-16 x 0.75 Button Head
Socket Cap Screws.
Note: Finger tighten for now.
Multi-Piece Table
6
2x
2x
2x

5) Assembly:
INSTALLATION GUIDE
Figure 5.4
Figure 5.5
Figure 5.6
4. Fully tighten all the 3/8-16 x 0.75 Button Head
Socket Cap Screws.
5. On a non-marring surface, connect your Top pieces
together using the Zipbolt Tight Joint connector.
Note: Make sure pieces are flush and aligned before
fully tightening the Zipbolt.
6. On a non-marring surface, center the assembled
base on the Top and attach using the #8 x 0.75 Pan
Head Phillips Wood Screws.
Note: Screws go through clearance holes in bottom of
the Tube.
Multi-Piece Table
7
4x

5) Assembly:
INSTALLATION GUIDE
Figure 5.7
7. With the Table flipped in the upright position, level
the Table using the glides in the bottom of each leg.
Multi-Piece Table
8

12900 Christopher Drive Lowell, MI 49331
800.815.7251 www.enwork.com
Specifications subject to change without notice.