Enwork eBench Table User manual

eBench Table
Revision A 02/01/17
Conference Table
Installation Instruction

1) Parts and Fasteners Included
INSTALLATION GUIDE
3
EBE48 for 48”D tables
EBE60 for 60”D tables
End Base
EBCB48 / EBCB60 / EBCB72
Crossbar
EBDD60
Connection Bar
EBSL
Mid Run Support Leg
EBM-1327
Power Infeed Cover
EBF1
Washer Without Thread
EBF2
Washer With Thread
EBF3
Plastic Crossbar Connector
EBF9A
Plastic Glide

1) Parts and Fasteners Included
INSTALLATION GUIDE
4
200-28147
M8-1.25 x 40MM LOW HD
SOCKET CAP SCREW
200-26469
M8-1.25 x 45MM FLAT HEAD
SOCKET CAP SCREW
200-04314
10 x 1 ½” PAN HEAD
PHILLIPS
200-28470
MINI ZIPBOLT CONNECTOR

2) Tools and Supplies Required
INSTALLATION GUIDE
5
4MM & 5MM ALLEN
WRENCH DRILL / DRIVER #2 PHILLIPS DRIVER BIT

3) Model Number Overview
INSTALLATION GUIDE
6
1 Bar eBench Table
EBZ4848 / EBZ4860 / EBZ4872
EBZ6048 / EBZ6060 / EBZ6072
2 Bar eBench Table
EBZ4896 / EBZ48120 / EBZ481442
EBZ6096 / EBZ60120 / EBZ601442

3) Model Number Overview
INSTALLATION GUIDE
7
3 Bar eBench Table
EBZ481443 / EBZ48156 / EBZ48168 / EBZ48180 / EBZ48192 / EBZ48204 / EBZ48216
EBZ601443 / EBZ60156 / EBZ60168 / EBZ60180 / EBZ60192 / EBZ60204 / EBZ60216
Cont.
4 Bar eBench Table
EBZ482404
EBZ602404

3) Model Number Overview
INSTALLATION GUIDE
8
5 Bar eBench Table
EBZ482405
EBZ602405
Cont.
Chart shows crossbar configuration for each length of table

3) Model Number Overview
INSTALLATION GUIDE
9
EBCBxx Lengths
Crossbars EBCBxx

4) Assembly:
INSTALLATION GUIDE
10
Fig. 1
- Attach EBF1 to all crossbar ends (EBCB48,
EBCB60, EBCB72)
Fig. 3
- Connect crossbar to EBE48 or EBE60 using
qty. 1, EBF1, EFF2 and 200-28147
- Repeat for all crossbars.
-Note
- Connection to mid run leg shown in Fig. 2 is
the same as shown in Fig. 3.
Fig. 2 (for 2, 3, 4 and 5 bar tables only)
- Connect qty 2, EBDD60 to qty 2, EBSL using
fastener 200-26469, flat head screw.
-Note
- Holes on side of EBDD60 face outward.
- Countersunk holes on EBDD60 face up.
Fig. 4
- Remove backer from disks on crossbar
(EBCB48 / EBCB60 / EBCB72) and attach
plastic disk (EBF9A) to adhesive.
- Place one EBF9A at all locations of stickers.

4) Assembly
INSTALLATION GUIDE
11
Fig. 5
Attach surface using qty 2, 200-04314 screws through all EBF3 parts. Surface is centered all around base.
Fig. 6
Leg cover EBM-1327 magnetically attaches to mid run legs for power / cord concealment.

12900 Christopher Drive Lowell, MI 49331
800.815.7251 www.enwork.com
Specifications subject to change without notice.