Enwork Grid XTB User manual

Rev 0715
Grid XTB
with UMM bases
(Shipped after March, 2015)
Installation Instructions

Tools Needed
1/4” Drive Socket Wrench
13mm Socket
Drill/Driver
#2 Phillips Bit
#2 Square Drive
5mm & 6mm
Allen Wrench Tape Measure
3/8” Box End
Wrench
1

M8 –1.25 X 12MM
Button socket head
cap screw (qty 8)
M6 - 1.0 x 30mm
Socket head cap screw
(qty 12)
Socket Bushing
(qty 12)
PARTS AND HARDWARE
NEEDED FOR STEP 1
Top Supports
Left Hand Column
Right Hand Column
Rail Components
2

RIGHT SIDE
OUTER RAIL
LEFT SIDE
OUTER RAIL
INSIDE RAIL
M8 –1.25 X
12MM
PRESSURE
PLATE
SOCKET
BUSHING
M6-1.0 X
30MM
STEP 1: ASSEMBLE ALL SINGLE
SIDES OF GRID BASES
3

STEP 2: ASSEMBLE LINKS AND
RISERS
Without Riser
Assembly
With Riser
Assembly
1/4-28 X 1” Pan
Head Machine Screw
1/4-28 X 3” Pan
Head Machine Screw 1/4-28 X 3” Pan
Head Machine Screw
1/4-28 Hex Nut
1/4-28 X 1” Pan Head
Machine Screw
(qty 1 for optional
riser)
1/4-28 X 3” Pan Head
Machine Screw
(qty 1)
1/4-28 Hex Nut
(qty 1)
NOTE:
Link Length will be 22” long for 24” deep work surface
assemblies, and 28” long for 30” deep work surface assemblies.
4

STEP 3 TERMINOLOGY
End of Run
Mid Run
End of Run
5

STEP 3: ASSEMBLE 2-PACK
GRID BASES
End of Run,
WITHOUT End Panel
Mid Run, or End of
Run WITH End Panel
Take special notice to link orientation. Slots
must face towards the outside of the
assembly in all mid run conditions, and in all
end of run conditions where an end panel
will be installed. In end of run conditions
where there will be no end panel, the slots
must face toward the inside of the assembly.
M8 Flange Nut
M8 Flange Nut
(qty 8)
6

STEP 4: CONNECT INDIVIDUAL
2-PACKS INTO 4, 6, OR 8-PACKS
WORKSTATIONS
1/4-28 X 1” Pan Head
Machine Screw
1/4-28 X 1” Pan Head
Machine Screw
(qty 2 per Cross Link)
Cross Link (qty 2)
7

STEP 5: CONNECT FRAME TO
BASE
10-24 X 2” SOCKET
HEAD CAP SCREW
10-24 X 2” SOCKET
HEAD CAP SCREW
(qty 4 per frame)
UZWNUTA
(qty 4 per frame)
UZWNUTA
Align to center set of holes
in frame when attaching
8

STEP 6: LEVEL AND ALIGN
ENTIRE ASSEMBLY
ALIGN SPINE
LEVEL ALONG SPINE LEVEL ASSEMBLY
9

STEP 7: REMOVE FRAME
TOP CAP
Use #2 square drive bit to
remove attachment screws
10

STEP 8: CONNECT
FRAMES
10-24 X 3/8” PAN
HEAD SCREW
(qty 2)
10-24 NYLOCK NUT
(qty 2)
11

STEP 9: POWER AND
DATA CONNECTIONS
MAKE ALL POWER AND DATA CONNECTIONS,
DROPPING THE CABLES IN THE OPENING CREATED
BY REMOVING THE FRAME TOP CAP IN STEP 6.
EXAMPLES SHOWN IN PICTIRES BELOW.
STEP 10: RECONNECT
GRID TOP CAP THAT WAS
REMOVED IN STEP 6
12

STEP 11: ATTACH TOPPER
SCREENS
a) CHECK TO BE SURE CHANNEL IN FRAME IS CLEAR OF DEBRIS
b) TRIM GASKET TO LENGTH OF TOPPER SCREEN
c) INSTALL GASKET ONTO SCREEN
d) WIPE OUTSIDE OF GASKET DOWN WITH SOAPY WATER IN
ORDER TO HELP LUBRICATE INSTALLATION
e) USING TWO PEOPLE, CENTER GASKET ON FRAME, AND FIRMLY
PRESS DOWN INTO CHANNEL. BE SURE THAT SCREEN BOTTOMS
OUT FULLY INTO THE CHANNEL.
Channel
Topper Screen
Gasket
13

STEP 12: ATTACH
WORKSURFACES
14

STEP 13: END PANELS
b) ATTACH BRACKET TO END PANEL
c) ATTACH END PANEL TO GRID ASSEMBLY
a) INSTALL THREADED INSERTS INTO END PANEL
Socket Bushing
(qty 4 per end panel)
M6 - 1.0 x 30mm
Socket head cap screw
(qty 4 per and panel)
Threaded Insert
(qty 4 per end panel)
M6 - 1.0 x 30mm
Socket head cap screw
Socket Bushing
Threaded Insert
Use 6mm allen wrench to
install
1/4-28 X 1” Pan Head
Machine Screw
1/4-28 X 1” Pan Head
Machine Screw
(qty 2 per end panel)
a) b)
c)
15