Erbe Bipolar LAP forceps (E) User manual

DISMANTLING AND ASSEMBLING
Bipolar LAP forceps (E) and bipolar LAP scissors (E)
Dismantling the product The product must be cleaned and disinfected in disassembled condition with jaws opened.
Caution: Never pull the jaws apart
manually, as this would cause damage
to the instrument.
1 Pull out the connecting cable from the
handle (no illustration).
2 Press both unlocking buttons (d) on the
handle simultaneously and remove the shaft
tube from the handle.
3 Screw the insert out of the shaft tube,
grasping it by the joint sleeve (e).
4 Withdraw the insert from the shaft tube.
5 To open the jaws, hold the insert by the
joint sleeve (e) and push the rod (b) in the
direction of the jaws.
Assembling the product
Caution: Never press the jaws together
manually, as this would cause damage to
the instrument.
1 To close the jaws, hold the insert by the
joint sleeve (e) and pull the rod (b).
2 Insert the insert (c) into the shaft tube (b). 3 Screw in the insert up to the stop position,
grasping it by the joint sleeve (e).
4 Press the rear unlocking button on the
handle (d) and insert the shaft tube into the
handle until it snaps into place at the stop
position.
The complete instrument
The three disassembled components:
a Handle, b Shaft tube and c Insert
d d ee b
ec b
d
be
c a
b
For the complete notes on use, refer to erbe-med.com

Erbe Elektromedizin GmbH
Waldhoernlestrasse 17
72072 Tuebingen
Germany
Phone [phone]
Fax [phone]
[email protected]
erbe-med.com
© Erbe Elektromedizin GmbH 2015 11.15 85110-111
Inserts for bipolar LAP forceps (E) Pieces No.
Insert for LAP/E LAP forceps Maryland,
deep-ribbed, ø 5 mm, length 340 mm 120195-143
Insert for LAP/E LAP forceps,
fenestrated, deep-ribbed, ø 5 mm, length 340 mm 120195-14 4
Insert for bipolar LAP scissors (E) Pieces No.
Insert for bipolar LAP/E LAP scissors Metzenbaum,
ø 5 mm, length 340 mm 120195-242
Individual components for bipolar LAP forceps (E) and bipolar LAP scissors (E) Pieces No.
Shaft tube for bipolar LAP forceps and LAP scissors,
ø 5 mm, length 340 mm 120195-141
Handle for bipolar LAP forceps and LAP scissors 120195-140
Shaft tube for bipolar E LAP forceps and E LAP scissors,
ø 5 mm, length 340 mm 120195-241
Handle for bipolar E LAP forceps and E LAP scissors 120195-245
Accessories for bipolar LAP forceps (E) and bipolar LAP scissors (E) Pieces No.
Cleaning brush, length 650 mm,
for manual cleaning and disinfection 120191-279
Rinsing tube with Luer Lock connector, length 500 mm,
for cleaning and disinfection by machine 120195-201

DISMANTLING AND ASSEMBLING
BiClamp®LAP forceps and BiClamp®E LAP forceps
Dismantling the product The product must be cleaned and disinfected in disassembled condition with jaws opened.
Caution: Never pull the jaws apart
manually, as this would cause damage
to the instrument.
1 Press both unlocking buttons on the handle
(d) simultaneously and withdraw the shaft
tube from the handle.
2 Screw the insert out of the shaft tube,
grasping it by the joint sleeve (e).
3 Withdraw the insert from the shaft tube.
4 To open the jaws, hold the insert by the
joint sleeve (e) and push the rod (c) in the
direction of the jaws.
Assembling the product
Caution: Never press the jaws together
manually, as this would cause damage to
the instrument.
1 To close the jaws, hold the insert by the
joint sleeve (e) and pull the rod (b).
2 Insert the insert (c) into the shaft tube (b). 3 Screw in the insert up to the stop position,
grasping it by the joint sleeve (e).
4 Press the rear unlocking button on the
handle (d) and insert the shaft tube into the
handle until it snaps into place at the stop
position.
The complete instrument
The three disassembled components:
a Handle, b Shaft tube and c Insert
d d
ee b
e cb
d
be
ca b
For the complete notes on use, refer to erbe-med.com

Erbe Elektromedizin GmbH
Waldhoernlestrasse 17
72072 Tuebingen
Germany
Phone [phone]
Fax [phone]
[email protected]
erbe-med.com
© Erbe Elektromedizin GmbH 2015 11.15 85110-112
Insert and individual components for BiClamp LAP Pieces No.
Insert for BiClamp 110, smooth, ø 5 mm, length 110 mm 120195-232
Shaft tube for BiClamp 110, ø 5 mm, length 110 mm 120195-234
Shaft tube for BiClamp LAP forceps 120195-141
Handle for BiClamp LAP forceps and BiClamp 110,
with connecting cable 4 m and MF plug 120195-145
Individual components for BiClamp E LAP Pieces No.
Shaft tube for BiClamp E LAP forceps,
ø 5 mm, length 340 mm 120195-241
Handle for BiClamp E LAP forceps,
with connecting cable 4 m and MF plug 120195-240
Inserts for BiClamp LAP and BiClamp E LAP Pieces No.
Insert for BiClamp LAP / E LAP forceps Kelly,
ø 5 mm, length 340 mm 120195-236
Insert for BiClamp LAP / E LAP forceps Maryland,
semi-deep ribbed, ø 5 mm, length 340 mm 120195-146
Insert for BiClamp LAP / E LAP forceps Maryland,
smooth, ø 5 mm, length 340 mm 120195-147
Insert for BiClamp LAP / E LAP forceps, fenestrated,
semi-deep, ø 5 mm, length 340 mm 120195-148
Insert for BiClamp LAP / E LAP forceps, fenestrated,
smooth, ø 5 mm, length 340 mm 120195-149
Reconditioning accessories for BiClamp LAP and BiClamp E LAP Pieces No.
Cleaning brush, length 650 mm,
for manual cleaning and disinfection 120191-279
Rinsing tube with Luer Lock connector, length 500 mm,
for cleaning and disinfection by machine 120195-201

DISMANTLING AND ASSEMBLING
LAP BiSect scissors
Dismantling the product The product must be cleaned and disinfected in disassembled condition with jaws opened.
1 Pull out the connecting cable
(no illustration).
2 Hold the handle (a) in such a way that the
moving handle is not obstructed. Press the
push-button and withdraw the shaft (c)
from the handle.
3 Hold the electrode by the insulation (b)
between your thumb and index nger.
Screw the electrode out of the shaft by
turning the rotary wheel (e) (approx. 6
turns).
4 Withdraw the electrode (d) from the shaft.
5 Pull the insulating tube (b) off the shaft.
Assembling the product
1 Push the insulating tube (b) onto the shaft
(c).
2 Insert the electrode (d) into the shaft up to
the stop position.
3 Hold the electrode by the insulation (b)
between your thumb and index nger.
Screw the electrode in, tightening it well,
by turning the rotary wheel (e) (approx. 6
turns); do not jam the thread.
4 Hold the handle (a) just like you would hold
a pen in such a way that the handles face
upwards and the moving handle is not ob-
structed, and press the push-button. Insert
the shaft into the handle (a) until it snaps
into place, without jamming it.
The complete instrument
The four disassembled components:
a Handle b Insulating tube c Shaft d Electrode
c
a
e
d b
cd
b
a
e
For the complete notes on use, refer to erbe-med.com
b
a
c
b
d
b

Erbe Elektromedizin GmbH
Waldhoernlestrasse 17
72072 Tuebingen
Germany
Phone [phone]
Fax [phone]
[email protected]
erbe-med.com
© Erbe Elektromedizin GmbH 2015 11.15 85110-113
Insert for LAP BiSect scissors Pieces No.
Insert for LAP BiSect Micro, ø 5 mm, length 350 mm 120195-206
Insert for LAP BiSect scissors Pieces No.
Insert for LAP BiSect Macro (20195-205), ø 5 mm,
length 350 mm 120195-207
Individual components for LAP BiSect Micro and Macro scissors Pieces No.
Shaft tube for LAP BiSect Micro and Macro,
ø 5 mm, length 350 mm 120195-208
Insulated tube for LAP BiSect Micro and Macro,
ø 5 mm, length 350 mm 120195-209
Handle for LAP BiSect Micro and Macro 120195-210
Reconditioning accessories for LAP BiSect Micro and Macro scissors Pieces No.
Cleaning brush, length 650 mm,
for manual cleaning and disinfection 120191-279
Rinsing tube with Luer Lock connector, length 500 mm,
for cleaning and disinfection by machine 120195-201