ETAS XETK-S22.0 User manual

www.etas.com
XETK-S22.0
Emulator Probe for Renesas RH850 /
V850 MCU Family
User’s Guide

Copyright
The data in this document may not be altered or amended without special noti-
fication from ETAS GmbH. ETAS GmbH undertakes no further obligation in
relation to this document. The software described in it can only be used if the
customer is in possession of a general license agreement or single license.
Using and copying is only allowed in concurrence with the specifications
stipulated in the contract.
Under no circumstances may any part of this document be copied, reproduced,
transmitted, stored in a retrieval system or translated into another language
without the express written permission of ETAS GmbH.
© Copyright 2020 ETAS GmbH, Stuttgart
The names and designations used in this document are trademarks or brands
belonging to the respective owners.
XETK-S22.0 - User’s Guide R05 EN - 06.2020

ETAS Contents
Contents
XETK-S22.0 - User’s Guide 3
1 About this Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1 Classification of Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2 Presentation of Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.3 Typographical Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.4 Presentation of Supporting Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 Basic Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1 General Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2 Requirements for Users and Duties for Operators . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.3 Intended Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4 Identifications on the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.5 Taking the Product Back and Recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.6 CE marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.7 RoHS Conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.7.1 European Union . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.7.2 China. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.8 Declarable Substances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.9 Use of Open Source Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2.1 General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2.2 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2.3 3rd Party Debugger Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4 Hardware Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.1 Architecture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.2 ECU Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.3 XETK Ethernet Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.4 Debug Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.5 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.6 ECU Voltage Supervisor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.7 Status LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.8 Data Emulation and Data Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.9 XETK-S22.0B: JTAG Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.10 XETK-S22.0D: JTAG and Aurora Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.11 Trigger Modes: Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.12 Pinless Triggering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.12.1 Startup Handshake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.12.2 XETK Trigger Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Contents

ETAS Contents
XETK-S22.0 - User’s Guide 4
4.13 Timer Triggering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.14 Trace Triggering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.15 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.16 Pull CalWakeUp until Startup Handshake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
5 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5.1 Mounting the XETK-S22.0 to the ECU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5.1.1 Mechanical connection of the XETK-S22.0 to the ECU Housing. . . . . . . 31
5.2 Electrical Connection to the ECU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
5.3 Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
5.3.1 XETK Ethernet Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
5.3.2 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
6 XETK Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
6.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
6.2 Configuration Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
7 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
7.1 System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
7.1.1 ETAS Compatible Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
7.1.2 PC with one Ethernet Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
7.1.3 XETK-S22.0 Software Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
7.2 Data Emulation and Measurement Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
7.2.1 Data Emulation Memory and Microcontroller Support . . . . . . . . . . . . . . . 44
7.2.2 Measurement Data Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
7.3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
7.4 XETK Ethernet Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
7.5 Environmental Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
7.6 Power Supply: XETK-S22.0B and XETK-S22.0D. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
7.7 Test Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
7.8 JTAG Timing Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
7.8.1 JTAG Timing Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
7.8.2 JTAG Timing Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
7.9 Debugger Timing Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
7.9.1 Debugger Arbitration Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
7.9.2 Debugger Arbitration Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . 48
7.10 Aurora Trace Timing Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
7.11 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
7.11.1 ECU Interface Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
7.11.2 ECU Interface Connector CON1 (5.0V Interface selected) . . . . . . . . . . . . 50
7.11.3 ECU Interface Connector CON1 (3.3V Interface selected) . . . . . . . . . . . . 52
7.11.4 Debugger Interface Connector CON3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
7.12 Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
7.12.1 XETK-S22.0B ECU Interface Connector CON1 . . . . . . . . . . . . . . . . . . . . . . 55
7.12.2 XETK-S22.0D ECU Interface Connector CON1 . . . . . . . . . . . . . . . . . . . . . . 57
7.12.3 Debugger Interface Connector CON3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
7.12.4 Interface and Power Supply Connector CON4 . . . . . . . . . . . . . . . . . . . . . . 58

ETAS Contents
XETK-S22.0 - User’s Guide 5
7.13 Mechanical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
8 Cables and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
8.1 ECU Adapter Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
8.1.1 CBAM230 Adapter Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
8.1.2 CBAM240 Adapter Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
8.1.3 CBAM271 Adapter Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
8.2 Combined Interface and Power Supply Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
8.3 PC Interface Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
8.3.1 CBE200-3 Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
8.3.2 CBAE200 Adapter Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
8.4 ETAS Module Interface Adapter Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
8.4.1 CBE230 Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
8.4.2 CBAE330 Adapter Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
8.5 Power Supply Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
8.5.1 Cable K70.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
8.5.2 Power Supply Cable KA50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
8.6 ECU Interface Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
8.6.1 XETK - ECU Adapter ETAM2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
8.6.2 XETK - ECU Adapter ETAM5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
8.6.3 XETK - ECU Adapter ETAM9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
8.6.4 XETK - ECU Adapter ETAN1A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
8.6.5 XETK - ECU Adapter ETAN4A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
8.6.6 XETK - ECU Adapter ETAN6A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
8.6.7 XETK - ECU Adapter ETAN2A with Aurora for XETK-S22.0D . . . . . . . . . . 70
8.6.8 XETK - ECU Adapter ETAN7A with Aurora for XETK-S22.0D . . . . . . . . . . 72
8.6.9 Debug Adapter AS_ETAF13.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
8.7 Water proof case ETKS_C3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
9 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
9.1 XETK-S22.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
9.2 XETK - ECU Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
9.3 Debug Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
9.4 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
9.5 Mounting Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
9.6 Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
9.6.1 ECU Adapter Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
9.6.2 Combined ECU Adapter and Power Supply Cables . . . . . . . . . . . . . . . . . . 78
9.6.3 Ethernet Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
9.6.4 Power Supply Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
9.7 Waterproof Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
10 ETAS Contact Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

ETAS About this Document
XETK-S22.0 - User’s Guide 6
1 About this Document
1.1 Classification of Safety Messages
The safety messages used here warn of dangers that can lead to personal
injury or damage to property:
1.2 Presentation of Instructions
The target to be achieved is defined in the heading. The necessary steps for this
are in a step-by-step guide:
Target definition
1. Step 1
2. Step 2
3. Step 3
>Result
DANGER
indicates a hazardous situation with a high risk of death or serious injury if
not avoided
WARNING
indicates a hazardous situation of medium risk which could result in death or
serious injury if not avoided.
CAUTION
indicates a hazardous situation of low risk which may result in minor or
moder-ate injury if not avoided.
NOTICE
indicates a situation which may result in damage to property if not avoided.

ETAS About this Document
XETK-S22.0 - User’s Guide 7
1.3 Typographical Conventions
Software
Hardware
1.4 Presentation of Supporting Information
OCI_CANTxMessage msg0 = Code snippets are presented on a gray back-
ground and in the Courier font.
Meaning and usage of each command are
ex-plained by means of comments. The
comments are enclosed by the usual syntax
for comments.
Choose File Open. Menu commands are shown in boldface.
Click OK. Buttons are shown in boldface.
Press <ENTER>. Keyboard commands are shown in angled
brackets.
The "Open File" dialog box is
displayed.
Names of program windows, dialog boxes,
fields, etc. are shown in quotation marks.
Select the file setup.exe. Text in drop-down lists on the screen, pro-
gram code, as well as path- and file names
are shown in the Courier font.
A distribution is always a one-
dimensional table of sample
points.
General emphasis and new terms are set in
italics.
Bold Menu commands, buttons, labels of the product
Italic Emphasis on content and newly introduced terms
NOTE
Contains additional supporting information.

ETAS Basic Safety Notices
XETK-S22.0 - User’s Guide 8
2 Basic Safety Notices
This chapter contains information about the following topics:
• “General Safety Information” on page 8
• “Requirements for Users and Duties for Operators” on page 8
• “Intended Use” on page 8
• “Identifications on the Product” on page 11
• “Taking the Product Back and Recycling” on page 12
•“CEmarking”onpage12
• “RoHS Conformity” on page 13
• “Declarable Substances” on page 13
• “Use of Open Source Software” on page 13
2.1 General Safety Information
Please observe the Product Safety Notices ("ETAS Safety Notice") and the fol-
lowing safety notices to avoid health issues or damage to the device.
ETAS GmbH does not assume any liability for damages resulting from
improper handling, unintended use or non-observance of the safety precau-
tions.
2.2 Requirements for Users and Duties for Operators
The product may be assembled, operated and maintained only if you have the
necessary qualification and experience for this product. Incorrect operation or
operation by users without sufficient qualification may lead to injuries or death
or property damages.
General Safety at Work
The existing regulations for safety at work and accident prevention must be
followed. All applicable regulations and statutes regarding operation must be
strictly followed when using this product.
2.3 Intended Use
An ETK is an electronic component that is installed in a vehicle control unit
(ECU) to read data from the ECU or write data to the ECU.
Application Area of the Product
This product was developed and approved for automotive applications. For use
in other application areas, please contact your ETAS contact partner.
NOTE
Carefully read the documentation (Product Safety Advice and this User's
Guide) that belongs to the product prior to the startup.

ETAS Basic Safety Notices
XETK-S22.0 - User’s Guide 9
Requirements for Operation
The following requirements are necessary for safe operation of the product:
• Use the product only according to the specifications in the correspond-
ing User's Guide. With any deviating operation, the product safety is no
longer ensured.
• Observe the regulations applicable at the operating location concerning
electrical safety as well as the laws and regulations concerning work
safety!
• Do not apply any voltages to the connections of the product that do not
correspond to the specifications of the respective connection.
• Connect only current circuits with safety extra-low voltage in accordance
with EN 61140 (degree of protection III) to the connections of the prod-
uct.
• The power supply for the product must be safely disconnected from the
supply voltage. For example, use a car battery or a suitable lab power
supply.
• Use only lab power supplies with double protection to the supply system.
• Ensure that the connections of the power supply are easily accessible.
• The module does not have an operating voltage switch.
– Switch on the product by connecting the power supply cable with the
power supply or by switching on the power supply.
– Switch off the product by disconnecting it from the power supply or
by switching off the power supply.
DANGER
Connect the power cord only with a vehicle battery or with a lab power sup-
ply! A connection to power outlets is prohibited.
Route the power cord in such a way that it is protected against abrasion,
damages, deformation and kinking. Do not place any objects on the power
cord.
Never apply force to insert a plug into a socket. Ensure that there is no con-
tamination in and on the connection, that the plug fits the socket, and that you
correctly aligned the plugs with the connection.
Do not use the product in a wet or damp environment.
Do not use the product in potentially explosive atmospheres.
Keep the surfaces of the product clean and dry.

ETAS Basic Safety Notices
XETK-S22.0 - User’s Guide 10
Potential Equalization
Requirements for the technical State of the Product
The product is designed in accordance with state-of-the-art technology and
recognized safety rules. The product may be operated only in a technically flaw-
less condition and according to the intended purpose and with regard to safety
and dangers as stated in the respective product documentation. If the product
is not used according to its intended purpose, the protection of the product
may be impaired.
Maintenance and Cleaning
The product is maintenance-free. Use a lightly moistened, soft, lint-free cloth
for cleaning the product. Ensure that no moisture can enter. Never spray clean-
ing agents directly onto the product. Do not user any sprays, solvents or abra-
sive cleaners which could damage the product.
Transport and Installation
CAUTION
Danger from inadvertent current flow!
Depending on the design, the shield of the Ethernet cables can be connected
with the housing of the module. Install the products only on components with
the same electrical potential or isolate the products from the components.
CAUTION
The ETK can be damaged or destroyed!
Some components of the ETK board may be damaged or destroyed by elec-
trostatic discharges. Please keep the ETK in its storage package until it is
installed.
The board should only be taken from its package, configured, and installed at
a work place that is protected against static discharge.
CAUTION
During installation and removal, ECU and ETK must be in a de-eenergized
state!
CAUTION
Risk of short circuiting the internal signals of the ETK!
When you mount the ETK to the ECU, you must ensure that the screws and
washers used will not penetrate the ETK printed circuit board.

ETAS Basic Safety Notices
XETK-S22.0 - User’s Guide 11
Cabling
Use exclusively ETAS cables at the connections of the product! Adhere to the
maximum permissible cable lengths! Observe the assignment of the cables to
the connectors! Detailed information about cabling is located in the ETK User's
Guides.
2.4 Identifications on the Product
Fig. 2-1 Adhesive Label (Example: Label for XETK-S14.0)
The following symbols are used for identifications of the product:
CAUTION
Differences in case ground potentials can cause high currents to flow
through the shields of the cables that connect various system modules.
Ensure that the module mounting surfaces are at the same electrical poten-
tial or insulate the modules from their mounting surfaces.
Symbol Description
The User's Guide must be read prior to the startup of the
product!
Symbol for WEEE, see chapter 2.5 on page 12
Symbol for CE conformity, see chapter 2.6 on page 12
Symbol for China RoHS, see chapter 2.7.2 on page 13
Symbol for China RoHS, see chapter 2.7.2 on page 13
Symbol for electrostatic sensitive components
XETK-S14.0A Product designation (example)

ETAS Basic Safety Notices
XETK-S22.0 - User’s Guide 12
2.5 Taking the Product Back and Recycling
The European Union has passed a directive called Waste Electrical and Elec-
tronic Equipment, or WEEE for short, to ensure that systems are setup through-
out the EU for the collection, treating and recycling of electronic waste.
This ensures that the devices are recycled in a resource-saving way represent-
ing no danger to health or the environment.
Fig. 2-2 WEEE-Symbol
The WEEE symbol (see Fig. 2-2 on page 12) on the product or its packaging
shows that the product must not be disposed of as residual garbage.
The user is obliged to collect the old devices separately and return them to the
WEEE take-back system for recycling. The WEEE directive concerns all ETAS
devices but not external cables or batteries.
For more information on the ETAS GmbH Recycling software, contact the ETAS
sales and service locations.
2.6 CE marking
With the CE mark attached to the product or its packaging, ETAS confirms that
the product corresponds to the applicable product-specific European Direc-
tives. The CE Declaration of Conformity for the product is available upon
request.
F 00K 110 722 Order number of the product (example)
SN: yyxxxxx Serial number (7-digit)
XXXX/YY Product version
ZZZZ Year of manufacture
ETAS GmbH,
PO Box 300220,
70442 Stuttgart,
Germany
Manufacturer's address
NOTE
For symbols and product information one or several adhesive labels can be
used.
Symbol Description

ETAS Basic Safety Notices
XETK-S22.0 - User’s Guide 13
2.7 RoHS Conformity
2.7.1 European Union
The EU Directive 2011/65/EU limits the use of certain dangerous materials for
electrical and electronic devices (RoHS conformity).
This product does not contain any of the restricted substances specified in the
EU Directive 2011/65/EU or exceeds the maximum concentrations stipulated
therein. For individual electronic components used in our products, there are
currently no equivalent alternative substances, which is why we make use of
the exception 7C-I in Annex III of this Directive.
ETAS confirms that the product corresponds to this directive which is applica-
ble in the European Union.
2.7.2 China
ETAS confirms that the product meets the product-specific applicable guide-
lines of the China RoHS (Management Methods for Controlling Pollution
Caused by Electronic Information Products Regulation) applicable in China
with the China RoHS marking affixed to the product or its packaging.
2.8 Declarable Substances
European Union
Some products from ETAS GmbH (e.g. modules, boards, cables) use compo-
nents with substances that are subject to declaration in accordance with the
REACH regulation (EU) no.1907/2006.
Detailed information is located in the ETAS download center in the customer
information "REACH Declaration" (www.etas.com/Reach). This information is
continuously being updated.
2.9 Use of Open Source Software
The product uses Open Source Software (OSS). This software is installed in the
product at the time of delivery and does not have to be installed or updated by
the user. Reference shall be made to the use of the software in order to fulfill
OSS licensing terms. Additional information is available in the document "OSS
Attributions List" at the ETAS website www.etas.com.

ETAS Introduction
XETK-S22.0 - User’s Guide 14
3 Introduction
This section contains information about the basic features and applications of
the XETK-S22.0 Interface Board (ETK = Emulator Test Probe), hints to system
requirements for operating the XETK-S22.0, and other details.
3.1 Applications
The XETK-S22.0 is an Emulator Probe for Renesas RH850 / V850 microcontrol-
ler family. It is available in two variants with different measurement perfor-
mance: XETK-S22.0B and XETK-S22.0D. The XETK-S22.0B is a serial XETK
designed for use with the JTAG portion of the RH850 / V850 debug interface
(IEEE/ISTO 5001), while the XETK-S22.0D serial XETK designed for use with the
JTAG and Aurora Trace portions of the debug interface of the RH850.
Fig. 3-1 XETK-S22.0
The XETK-S22.0 supports the standard full duplex 100Base-T Ethernet inter-
face and can be connected directly or via ES51x/ES59x/ES600/ES89x/ES910
modules to the PC. No additional ETAS modules are required for the access to
the ECU. The XETK-S22.0 can be used for rapid prototyping applications
(bypass) as well as for measurement and calibration applications.
NOTE
Within this manual, the term "XETK-S22.0" describes features common to
both the XETK-S22.0B and XETK-S22.0D. The term "XETK-S22.0B" describes
features specific to the XETK-S22.0B variant, and the term "XETK-S22.0D"
describes features specific to the XETK-S22.0D variant.
NOTE
For supported RH850/V850 microcontrollers, refer to chapter 7.1.3
on page 41.
XETK-S22.0
XETK ECU interface connectors 40 pin Samtec plus 6pin Molex
Power supply for FCC devices
(VDDSTBY)
Configurable 1.09V or 1.25 V
SBRAM sense Yes, on board or external sense
Pinless triggering Yes
Timer triggering Yes
Trace triggering Yes (XETK-S22.0D only)

ETAS Introduction
XETK-S22.0 - User’s Guide 15
3.2 Features
3.2.1 General
• 100Mbit/s Ethernet Interface:
– Direct connection to PC
– Open XCP on Ethernet Protocol supporting a variety of standard
applications
• XETK-S22.0 JTAG Interface:
– Configurable JTAG output levels: 3.3 V or 5.0V
– Configurable JTAG interface clock speed: 10 MHz, 20 MHz, 25 MHz,
or 40 MHz
– JTAG Signals available on the 40 Pin Samtec connector
– Pinless startup protocol for XETK recognition and data acquisition
triggering
– Measurement raster down to 50µS
• XETK-S22.0D Aurora Interface
– Support of Aurora interface clock speed: 1.25GHz
– Aurora Signals available on the 40 pin Samtec connector
– Measurement raster down to 10 µS
• “ETK Drivers and Tools” update to support ETAS software tools (INCA,
XCT)
• Firmware update (programming of the logic device) through HSP soft-
ware service packs; removal of XETK or ECU is not necessary
• Mounting possibilities inside or on top of ECU
• ECU flashing via XETK
– Braindead flashing under ProF control
• Permanent storage of configuration in EEPROM
• Temperature range suitable for automotive application
3.2.2 Calibration
• Concurrent use of calibration and measurement performed via micro-
controller
• Working Page & Reference Page (2 page concept) realized by microcon-
troler overlay mechanism
• Microcontroller capability of internal Flash emulation can be used
• XETK powers Emulation Device RAM (for calibration purpose)
NOTE
The XETK-S22.0B is a subset of the XETK-S22.0D. All features in the XETK-
S22.0B are included in the XETK-S22.0D. Unique features to the XETK-S22.0D
will be identified accordingly.

ETAS Introduction
XETK-S22.0 - User’s Guide 16
• Supports “Start on Any Page”
• Supports special coldstart mechanism (“Calibration Wake Up”):
– Calibration Wake Up: Wake up mechanism to wake up the power sup-
ply of the ECU via the Calibration Wake up pin
– Pull CalWakeUp until Startup Handshake: duration of the Wake up
mechanism is configurable
3.2.3 3rd Party Debugger Interface
• XETK provides additional connector for external JTAG debug hardware
• Simultaneously use XETK and JTAG debugger
For more technical data on the XETK-S22.0, consult the chapter “Technical
Data” on page 41.

ETAS Hardware Description
XETK-S22.0 - User’s Guide 17
4 Hardware Description
In this chapter, the function blocks of the XETK-S22.0 are explained in detail.
4.1 Architecture
Fig. 4-1 shows the block diagram of the XETK-S22.0B, and Fig. 4-2 shows the
block diagram of the XETK-S22.0D.
Fig. 4-1 XETK-S22.0B Architecture
Fig. 4-2 XETK-S22.0D Architecture
XETK-S22.0B
CALWAKEUP
ECU
Interface
Connector s
FPGA
XCP on
Ethernet
Interface
SRAM
System
Functions
Arbiter
100
MBit/s
Ethernet
Phyte
r
Ethernet
Phy
Automatic
Power On
Ethernet
Traffic
Detection
Ethernet
Traffic
Detection
Power
Supply
Monitoring
ECU
Reset
&
Power
Control
MCU
Core
Ethernet
MAC
Measurement
& Calibration
Unit
ECU
Access
Unit
Serial Flash
Configuration
&
Manufacturing
Data
Time
Sync.
JTAG Signals
Resets + WD_DIS
Power
Supply
Standby
Supply
Power
Debugger
Connector
JTAG
Arbitration
Buffers
ECU
Buffers
ECU
SBRAM
POWER
SUPPLY
40-Pin Samtec
JTAG
Resets + WD_DIS
U-BATT Input
Debugger Signals
JTAG, WD_DIS, Resets, VCC
Sense
ECU &
SBRAM
Power
Supplies
Molex 6
DMA
Trigger
Unit
v02
XETK-S22.0D
CALWAKEUP
ECU
Interface
Connector s
FPGA
XCP on
Ethernet
Interface
SRAM
System
Functions
Arbiter
100
MBit/s
Ethernet
Phyte
r
Ethernet
Phy
Automatic
Power On
Ethernet
Traffic
Detection
Ethernet
Traffic
Detection
Power
Supply
Monitoring
ECU
Reset
&
Power
Control
Trace
Unit
MCU
Core
Ethernet
MAC
Measurement
& Calibration
Unit
ECU
Access
Unit
Serial Flash
Configuration
&
Manufacturing
Data
Time
Sync.
JTAG Signals
Resets + WD_DIS
Power
Supply
Standby
Supply
Power
Debugger
Connector
JTAG
Arbitration
Buffers
ECU
Buffers
ECU
SBRAM
POWER
SUPPLY
40-Pin Samtec
JTAG
Resets + WD_DIS
U-BATT Input
Debugger Signals
JTAG, WD_DIS, Resets, VCC
Sense
ECU &
SBRAM
Power
Supplies
Molex 6
DMA
Trigger
Unit
Aurora Trace Signals
Trace
memory
v01

ETAS Hardware Description
XETK-S22.0 - User’s Guide 18
While the microcontroller accesses the program data (not the program code)
out of the data emulation memory provided by the microcontroller, the content
of the data emulation memory can simultaneously be modified by the calibra-
tion and development system through the XETK Ethernet interface. This pro-
cess enables adjustments of parameters, characteristic lines and maps
through the calibration and development system.
Using an additional measurement data memory area, the ECU microcontroller
can provide data to the calibration and development system by buffering the
data (DISTAB) and triggering the XETK to read the data via JTAG. The XETK
then reads, buffers, processes and sends this measured data to the PC.
Using the Aurora Trace interface, the XETK-S22.0D can acquire additional mea-
surement data and send the measured data to the PC.
The 100 Mbit/s XETK Ethernet interface provides communication with the PC.
The power supply for the XETK-S22.0 is provided by a switch mode power sup-
ply, to minimize power dissipation.

ETAS Hardware Description
XETK-S22.0 - User’s Guide 19
4.2 ECU Interface
The XETK-S22.0 is connected via connectors CON1 and CON4 to the ECU with
two adapter cables (refer to Fig. 4-3 on page 19). The pin definition depends on
the application and the microcontroller type. In general the ECU interface con-
sists of
• 1 ECU voltage line, which is not used for XETK power supply, but only for
detection of the ECU status, therefore the power consumption on this
line is negligible (refer to chapter 4.5 on page 21)
• 1 Reset line which allows the XETK to control the system reset of the
ECU
• 1 Reset line which allows the XETK to monitor the system reset of the
ECU
• 5 JTAG Debug line interfaces for the communication between the XETK-
S22.0 and the microcontroller
• 1 differential Aurora Data lane
• 1 differential Aurora Clock
•1Watchdogtimerdisableline
• 7 ground lines for proper shielding of the ECU interface lines
Fig. 4-3 Location of the ECU Interface Connectors
CON1
CON4

ETAS Hardware Description
XETK-S22.0 - User’s Guide 20
4.3 XETK Ethernet Interface
The XETK Ethernet interface can be directly connected to the PC via CON2
(refer to Fig. 4-4). No additional ETAS module is required for the access to the
ECU.
The interface is a standard full duplex 100Base-TX Ethernet interface using the
XCP protocol. The XETK Ethernet interface is integrated in the ETAS IP world
with automatic IP management and supports the open automotive "Universal
Measurement and Calibration" standard "XCP on Ethernet" (TCP/IP, UDP/IP).
The open XCP on Ethernet interface allows for connecting to the
XETK-S22.0
with third party application softw
are.
Fig. 4-4 Location of the XETK Ethernet Interface Connector (CON2)
NOTE
The XETK Ethernet interface is not compatible with the ETK interfaces in
modules like e.g. ES910, ES590, ES591, ES592, ES593-D, ES595, ES1232-A.
The XETK Ethernet interface is compatible with the ECU interface of the
ES910 module and the Ethernet interfaces of the ES51x/ ES592/ ES593-D/
ES595/ ES600/ES88x/ES89x modules.
NOTE
Please see chapter 7.1.2 on page 41 for additional information regarding PC
requirements for the Ethernet interface.
CON2