ETC Desire D22 User manual

ETC Installation Guide
Desire®Series D22
Corporate Headquarters  Middleton, Wisconsin, USA  Tel [phone]
Service (Americas)  [email protected]
London, UK  Tel [phone]  Service: (UK) [email protected]
Rome, IT  Tel [phone]  Service: (UK) [email protected]
Holzkirchen, DE  Tel [phone]  Service: (DE) [email protected]
Hong Kong  Tel [phone]  Service: (Asia) [email protected]
Web: etcconnect.com  © 2016 Electronic Theatre Controls, Inc.  Product information and
specifications subject to change.  ETC intends this document to be provided in its entirety.
7411M2100  Rev D  Released 2016-12
Introduction
The Desire D22 is designed for indoor installations and has a rugged die-cast
enclosure, steel mounting yoke, and noise-free, fan-less operation.
The D22 can be pipe mounted with a C-clamp, canopy mounted, or track
mounted. Mounting accessories are available. Contact ETC Customer Service
for assistance; contact information is located at the bottom of this page.
For information about the operation of the D22 Desire Series, see the
Desire
Series by ETC D22, D40, D40XT, D60 User Manual . ETC manuals are available
for download at etcconnect.com.
CAUTION:
Do not attempt to install or use a fixture until you read
and understand the installation instructions and safety
labels.
WARNING:
This fixture must be installed by a qualified electrician
in accordance with all national and local electrical and
construction codes and regulations.
Portable Canopy Mount Track Mount

ETC Installation Guide
Desire D22
Desire D22 Page 2 of 8 ETC
Specifications
Environment
Operates in ambient temperatures of 0°C to +40°C (32°F to 104°F).
Control
Portable
The Portable D22 is provided with 5-pin XLR connectors on the back for In
and Thru connection to a DMX/RDM control network.
Canopy Mount
The D22 Canopy Mount fixture is provided with one cable, which provides
power and data into the canopy.
A termination board is incorporated into the mounting plate for installation
onto a voltage-separated junction box (junction box provided by others,
voltage barrier provided by ETC) and provides termination for control wiring:
• Connection of the D22 data cable to a provided screw-down
connector, which is pre-wired at the factory. The connector is plugged
into the termination board. The braided shield is connected inside the
fixture and should not be connected in the canopy.
• Connection of DMX/RDM input from the control source. This
connection can be cable type Belden 9729 (or equivalent) to the
provided screw terminal. When using Cat5 (or equivalent) cable type
for DMX/RDM input, order a Cat5 termination kit from ETC (part
number 4100A1013). Cat5 termination instructions and an IDC
connector are provided with the termination kit.
• Connection of DMX/RDM thru to the next DMX device. This
connection may also be either Belden 9729 or Cat5. The connector is
not provided. Order the appropriate DMX termination kit for the cable
type used from ETC (Belden 9729: 4100A1012; Cat5: 4100A1013).
Termination instructions and the appropriate connector is provided
with the termination kit. Up to 32 DMX/RDM devices can be
daisy-chained together per data run.
Track Mount
The Track Mount fixture’s power and data connections are made through the
DataTrack™(EUTRAC®) MultiAdapter mounting adapter. No further wiring to
the fixture is required. See the track installation instructions for more
information.
CAUTION:
Risk of eye injury. Do not stare directly into the light.
Do not operate in proximity to flammable materials.

ETC Installation Guide
Desire D22
Desire D22 Page 3 of 8 ETC
Electrical
The Desire D22 Portable fixture has a permanently installed power cord with
3-prong Edison connector. Region-specific connectors are available. Contact
ETC for available options. The Canopy Mount fixture is provided with power
and data wired to the canopy and should be terminated in a voltage-
separated junction box (provided by others). The Track Mount fixture receives
power through its MultiAdapter, which connects to one of two circuits.
Power Requirements
The universal power supply accepts 100–240 VAC 50/60Hz.
WARNING:
Ensure the main power supply is off before installing or
wiring a fixture.
CAUTION:
Do not use a fixture for any voltage for which it is not
rated. Do not exceed the specified voltage and current
input for any fixture. Connecting the fixture to a voltage
outside the acceptable range may damage the unit and
will void the factory warranty.
Note:
The fixture must be grounded.
Application-appropriate electrical junction box with
cord grips is required. A voltage-separated junction box
is required. A RACO 232 series 4 x 2-1/8 inch deep
junction box is recommended. The junction box must
not interfere with fixture focusing.
The fixture is factory pre-wired. Opening the housing is
not required.
The fixture must be connected to a non-dimmable
power source. Dimming the unit will damage the fixture
and void the factory warranty.
Power Connections
Mains Europe North America
Line Brown Black
Neutral Blue White
Ground Green/Yellow Green

ETC Installation Guide
Desire D22
Desire D22 Page 4 of 8 ETC
Installation
Termination
The D22 Desire Series requires termination at the last fixture on a DMX/RDM
line with a 120-ohm resistor.
• The Portable fixture is self-terminated.
• The Track Mount fixture is terminated with a DataTrack DMX Term
Block (ETC part number 7066A1030).
• The Canopy Mount fixture is terminated on the Termination board
inside the canopy.
Canopy Mounting Plate and Termination Board
Termination
The Canopy Mount fixture is
terminated with the S1
switch on the Termination
board. Set the switch to the
ON position to terminate the
last fixture. All others on the
DMX/RDM line must be set to
OFF.
Termination
board
Power block
Mounting plate
Termination switch
D22 Data connector

ETC Installation Guide
Desire D22
Desire D22 Page 5 of 8 ETC
Installing the Canopy Mount Fixture
The Canopy Mount fixture is installed on to a RACO 232 series 4 x 2-1/8 inch
deep double junction box. The fixture is supplied with a divider to separate
the data network from the line voltage inside the junction box.
DMX/RDM Cable Installation
1: Terminate DMX/RDM input from the
control source to the junction box.
If using Belden 9729:
a: See the
DMX Cable Preparation
for Screw Termination Setup
Guide for instructions to prepare
and terminate Belden 9729 for
DMX input cable to the screw
terminal connector.
b: Install the screw terminal
connector with wires terminated
to the DMX/RDM Input receptacle
on the termination board.
CAUTION:
Separate the line voltage from the data side in the
junction box. Install the voltage barrier provided by ETC.
Canopy
Installation hook
Junction box
(not provided)
Data/Voltage
divider
Mounting plate
assembly
From a DMX/RDM source
Data – (Black)
Data + (Red)
Belden 9729 (or equivalent) wire
termination to screw connector
4 to 8 = n/c
COM

ETC Installation Guide
Desire D22
Desire D22 Page 6 of 8 ETC
If using Category 5:
a: See the
Cat5 Cable Preparation for
IDC Termination Setup Guide for
instructions to prepare and
terminate Category 5 for DMX/RDM
input cable to the insulation
displacement connector.
b: Install the IDC connector with wires
terminated to the DMX/RDM Input
receptacle on the termination board.
2: Optionally, terminate DMX/RDM thru
to the next device in the DMX data run.
Up to 32 DMX/RDM devices can be
daisy-chained together per data run. See
Control on page 2 .
a: See the specific termination setup guide for the type of cable used
(either Belden 9729 or Category 5) in the installation. Termination
kits are ordered separately.
b: Install the connector with wires terminated to the DMX/RDM Thru
receptacle on the termination board.
3: Terminate DMX/RDM data signal for the last DMX/RDM device in the
data run by setting the termination switch on the termination board to
ON. All other devices in the data run maintain the factory default
termination switch setting OFF. See
Termination on page 4 .
Canopy Mounting Plate Installation
1: Install the divider in the junction box
with the provided screw, separating
the power side from the data side.
2: Strip the supply power wires back
1/2 inch (13 mm).
3: Use a #2 Phillips screwdriver to
remove the two screws retaining the
canopy to the mounting plate.
4: Following the label on the mounting
plate, attach the supply power wires
to the power block on the mounting plate. See
Canopy Mounting
Plate and Termination Board on page 4 .
5: Attach the power supply ground wire to the mounting plate.
6: Plug in the input DMX/RDM connector (and thru DMX/RDM
connector, if used) to the appropriate location on the terminal board.
7: Attach the mounting plate to the junction box, ensuring the cables are
properly routed inside the box.
Data – (ORG)
Data + (W/ORG)
Cat5 (or equivalent) wire
termination to IDC connector
COM
BRN
GRN
W/GRN
BLU
W/BLU

ETC Installation Guide
Desire D22
Desire D22 Page 7 of 8 ETC
Canopy Fixture Installation
1: Strip the fixture’s power wires back
1/2 inch (13 mm).
2: Using the hole in the mounting
bracket, hang the canopy on the
installation hook.
3: Following the label on the
mounting plate, attach the power
wires to the power block.
4: Secure the fixture ground wire to
the mounting plate.
5: If the fixture is the last fixture on a
DMX/RDM line, terminate the fixture. See
Termination on page 4 .
6: Insert the DMX/RDM connector into the Terminal board.
7: To determine the alignment of the canopy, orientate the fixture to
where it will need to be focused.
8: Align the holes in the canopy with the mounting posts on the
mounting plate and using a #2 Phillips screwdriver, secure the canopy
to the mounting plate with the canopy screws.
9: Focus the fixture.
10: Tighten the canopy tension nut to set additional resistance for the
rotation of the fixture.
Installing the Portable Fixture
The C-clamp attaches the fixture to the
mounting pipe. The position of the fixture can
be adjusted once it is mounted. Tightly fasten
the C-clamp to the yoke with the provided yoke
bolt and lock washer.
1: Place the C-clamp on the mounting pipe,
and then tighten the pipe bolt to secure it.
2: Loop a safety cable over the pipe and
attach the ends to the safety cable loop
on the body of the fixture.
3: Loosen the C-clamp yoke bolt and rotate the yoke to the desired
position.
4: Tighten the bolt to lock the fixture.
CAUTION:
Do not overtighten the canopy tension nut.
Installation
hook and
bracket
Canopy
tension
nut
Safety
loop

ETC Installation Guide
Desire D22
Desire D22 Page 8 of 8 ETC
Installing the Track Fixture
1: Insert the DataTrack adapter into
the track. The adapter only fits
into the track one way with the
tabs nesting into the track’s
groove.
2: Rotate the locking mechanisms to
lock the adapter into place.
3: Use the circuit selection lock to
select circuit 1 or 2. The desired
circuit number should point
toward the center of the adaptor.
4: Focus the fixture.
Addressing
Fixture addresses must be set between 1 and 510. Each Desire fixture must be
considered a separate DMX device for the purpose of DMX line-loading
calculations.
No more than 32 DMX devices can be daisy-chained together on a single run.
For runs of fixtures totaling more than 32 DMX devices, a DMX splitter will
need to be used to split the DMX runs.
When using RDM with track fixtures, ETC recommends connecting no more
than 20 fixtures on a single run.
Initial Power Up
Control and configuration of the Desire D22 can be achieved over a
DMX/RDM control network, or directly from a connected computer running
appropriate software. When controlling the D22 directly from a PC, a
Gadget II Interface or DMX/RDM gateway is required.
CAUTION:
Tighten the C-clamp pipe bolt to about 18 inch lbs.
(Approximately finger tight plus up to one-quarter
turn.) Do not use excessive force.
WARNING:
When using the circuit selection lock, ensure the
selected circuit is a constant power circuit. Dialing into
a dimmable circuit may cause fixture damage that will
void the ETC warranty.