ETC Cyberlight LED User manual

High End Systems
Cyberlight LED
Automated Luminaire User Manual
Version 1.0.0
Part Number: 2597M1200-1.0.0 Rev: D
Released: 2022-04

To view a list of ETCtrademarks and patents, go to etcconnect.com/ip. All other trademarks, both marked
and not marked, are the property of their respective owners.
You can find complete High End Systems terms and conditions and warranty information at
etcconnect.com/Support/Warranty.aspx.
ETC intends this document, whether printed or electronic, to be provided in its entirety.

Table of Contents
Table of Contents i
Introduction 1
Important Safety Information 1
Help from Technical Services 2
Safety Considerations 3
General Operation and Use Guidelines 5
Unpack the Fixture 6
Remove the Yoke 6
Fixture Overview 7
Yoke Assembly 8
Specifications 8
Environment 8
Power 9
Electrical 9
Input and Power Factor 9
Fixtures per Circuit 9
Connector Specification 9
Fixture Installation Hardware 10
Install the Yoke 10
Install the Fixture 12
DMX Control 14
DMX Connector Pinout 14

Connect DMXCables to Fixture 14
Terminate DMX 15
Set the DMX Start Address 15
DMX Channels 15
Ethernet Control 16
Connect EthernetCables to a Fixture 16
Ethernet Control and DMX Thru 17
Terminate DMX 17
Set the DMX Start Address 17
Configure the Fixture 18
Navigate the User Interface 18
DMX Address 19
Settings Menu 19
Set the Control Options 19
Set the Network Options 20
Set the Pan/Tilt Options 21
Set the Dimming Options 21
Set the Fan Options 21
Set the Display Options 22
Software Update 22
Calibration Options 23
Restore Defaults 23
Home/Test Menu 23
Home Options 23
Test Options 24
Diagnostics Menu 24
Set Time Options 24
View Errors 24
View Fan Speed 24
View Sensors 25
View Temperatures 25
View DMXMonitor 25
View Software Version 25
ii Cyberlight LED User Manual

View Device 25
Change the Offset of the Mirror Head 26
Replace a Gobo 27
Considerations for Custom Gobos 27
Remove the Effects Module 27
Replace a Gobo 29
Install the Effects Module 33
Replace Color Media 34
Remove the Color Module 34
Replace Color Media 35
Install the Color Module 36
Install the Snoot Accessory 37
Error Codes 38
Maintenance 40
Clean Fans and Dust Filters 40
Clean the Mirror 41
Replace the Fuse 41
Compliance 42
FCC Compliance 42
Table of Contents iii

1 Cyberlight LED User Manual
Introduction
Congratulations on your purchase of the Cyberlight LED automated fixture. This manual
provides important information for the safe installation, configuration, and maintenance of
your Cyberlight LED fixture.
Important Safety Information
Please read all instructions prior to assembling, mounting, and operating this equipment.
Continued and safe operation of this fixture is the responsibility of the operator. This manual
will give tips for that continued safe operation. At any time please contact Technical Services
for any safety concerns.
The following international note, caution, and warning symbols appear in margins throughout
this manual to highlight important messages.
Note: Notes are helpful hints and information that is supplemental to the main text.
CAUTION: Hot Surfaces. This statement indicates that while operating,
equipment surfaces may reach very high temperatures. Allow the
fixture to cool before handling or servicing.
CAUTION: A Caution statement indicates situations where there may be
undefined or unwanted consequences of an action, potential for data loss or
an equipment problem.
WARNING: A Warning statement indicates situations where damage may
occur, people may be harmed, or there are serious or dangerous
consequences of an action
WARNING: RISK OF ELECTRIC SHOCK! This warning statement indicates
situations where there is a risk of electric shock.
All ETC High End Systems documents are available for free download from our website:
etcconnect.com/Products/High-End-Systems.
Please email comments about this manual to: [e-mail].

Introduction 2
Help from Technical Services
If you have questions that are not answered by this document, try the ETC support website at
support.etcconnect.com or the High End Systems product website at
etcconnect.com/Products/High-End-Systems. If none of these resources are sufficient, contact
ETC Technical Services directly at one of the offices identified below. Emergency service is
available from all offices outside of normal business hours.
When calling for help, take these steps first:
•
Prepare a detailed description of the problem
•
Go near the equipment for troubleshooting
•
Find your notification number if you have called in previously
ETC, Inc.
Americas
Technical Services Department
3031 Pleasant View Road
Middleton, WI 53562
800-775-4382 (USA, toll-free)
[phone]
[e-mail]
ETC GmbH
Germany, Austria, Switzerland,
Eastern Europe, and Russia
Technical Services Department
Ohmstrasse 3
83607 Holzkirchen, Germany
[phone]
[e-mail]
ETC Austin
High End Systems Products
Technical Services Department
2105 Gracy Farms Lane
Austin, TX 78758 USA
800-890-8989 (USA, toll-free)
[phone]
[e-mail]
ETC France
France
Zone Urbaparc -
Bâtiment E
6 Boulevard de la Libération
Saint-Denis, 93200
[phone]
[e-mail]
ETC Ltd
Europe, Middle East, and Africa
Technical Services Department
26-28 Victoria Industrial Estate
Victoria Road,
London W3 6UU England
[phone]
[e-mail]
ETCAsia
Asia
Technical Services Department
Room 1801, 18/F
Tower 1, Phase 1 Enterprise Square
9 Sheung Yuet Road
Kowloon Bay, Kowloon, Hong Kong
[phone]
[e-mail]

3 Cyberlight LED User Manual
Safety Considerations
To ensure safe operation, follow the safety instructions and warning notes in the user manual.
•
The Cyberlight LED is intended for professional use only. Not for residential use. Read the
entire manual before using this equipment.
•
Contact your authorized ETC dealer or Technical Services before performing any service in
order to maintain warranty coverage.
Symbols used on the product label are defined below:
1 m
The luminaire must be installed at least 1.0m (3ft
4in) away from all lighted objects.
Le luminaire doit être installé à au moins 1,0m
(3pi. 4po.) de tout objet éclairé.
General warning Avertissement général
Do not stare at the operating light source. Ne pas regarder la source de lumière lorsqu’elle
fonctionne.
This product should not be discarded as unsorted
waste but must be sent to separate collection
facilities for recovery and recycling.
Ce produit ne doit pas être jeté avec les déchets
ménagers mais doit être déposé dans une collecte
de déchets électroniques ou dans un point de
collecte.
taorTaRated maximum ambient temperature Température ambiante maximale recommandée
Operate indoors only, not where this product
would be exposed to the weather.
Ne fonctionne qu'à l'intérieur, pas là où ce produit
serait exposé aux intempéries.
WARNING: Note the following safety warnings before use:
•
This equipment is designed for operation by qualified personnel only.
•
Do not stare at the operating lamp. May be harmful to the eyes.
•
Replace fuses with the specified type and rating only. See page 41 .
•
Make sure that the available voltage is within the stated range. See page
9 .
•
Do not use this fixture with a damaged power lead (cord set). If the lead
is damaged, it must be replaced by a qualified technician with an
equivalent type before use. Contact your local authorized dealer for
spare power leads.
•
Do not mount the fixture on or near flammable surfaces.
•
The fixture should be positioned so that prolonged staring into the
fixture at a distance closer than 6.4 m (21 ft) is not expected.
•
Minimum distance from fixture head to combustible materials: 0.1 m (4
in).
•
Minimum distance to lighted objects:1.0m (3ft 4in).

Safety Considerations 4
AVERTISSEMENT : Pour votre sécurité, lisez les mises en garde et les avis
suivants avant toute utilisation :
•
Cet équipement est conçu pour être utilisé par un personnel qualifié
uniquement.
•
Ne regardez pas la lampe en fonctionnement. Peut être nocif pour les
yeux.
•
Remplacez les fusibles uniquement par le type et le calibre indiqués. Voir
page 41 .
•
Veillez à ce que la tension disponible soit dans la plage indiquée. Voir
page 9 .
•
N'utilisez pas ce projecteur avec un cordon d'alimentation endommagé
(fils électriques). Si le cordon est endommagé, un technicien qualifié doit
le remplacer par un cordon de type équivalent avant que l'appareil ne
puisse être utilisé. Contactez votre distributeur agréé local pour obtenir
des cordons d'alimentation de rechange.
•
Ne pas installer le projecteur sur ou à côté d’une surface inflammable.
•
L'appareil doit être positionné de manière à ce qu'un regard prolongé
dans l'appareil à une distance inférieure à 6,4 m (21 pi) soit peu probable.
•
Distance minimum entre la tête du luminaire et les matériaux
combustibles : 0.1 m (4 in).
•
Distance minimum avec les objets éclairés :1.0m (3ft 4in).
WARNING: RISK OF ELECTRIC SHOCK!
•
Do not operate this device with the cover open.
•
Disconnect the fixture from power and DMX and allow it to cool before
performing any cleaning and maintenance.
AVERTISSEMENT : RISQUE DE CHOC ÉLÉCTRIQUE!
•
N'utilisez pas cet appareil avec le couvercle ouvert.
•
Débrancher la lampe de son alimentation et du DMX et la laisser refroidir
avant d’effectuer un nettoyage ou un entretien.
CAUTION: Hot Surfaces. Allow the device to cool completely before
handling and servicing.
ATTENTION : Surfaces chaudes. Laissez le luminaire refroidir complètement
avant de le manipuler et de procéder à son entretien.
Note: The light source in this luminaire is not user-replaceable, and must be
replaced only by a qualified technician. Contact ETC Customer Support for assistance.

5 Cyberlight LED User Manual
General Operation and Use Guidelines
•
This fixture is only allowed to be operated with the maximum alternating current that is
stated in the technical specifications label provided on the fixture.
•
Lighting effects are not designed for permanent operation. Consistent operation breaks
may extend the life of the fixture.
•
When choosing the installation location, make sure the fixture will not be exposed to
extreme heat, moisture, or dust.
•
Do not point the mirror toward the sun or other bright light source. Doing so could
damage the fixture.
•
Operate the fixture only after having familiarized yourself with its functions. Do not permit
persons who are not qualified and familiar with its functions to operate the fixture.
•
Do not modify the fixture. Any modifications will void the warranty.
•
This manual describes the proper installation and operation of this fixture. Using this
fixture in any way other than the intended use may cause damage and void the warranty.
•
When the fixture has been stored or transported in cold temperatures, allow it to warm to
room temperature for a minimum of one hour before applying power. Applying power to a
cold fixture may cause damage to the fixture and void the manufacturer warranty.
•
Please use the original packaging if the fixture is to be transported. ETC will not be
responsible for the fixture if packaging other than manufacturer provided packaging is
used.

Unpack the Fixture 6
Unpack the Fixture
The Cyberlight LED shipping carton includes:
•
one (1) Cyberlight LED automated luminaire
•
one (1) power cord (powerCON TRUE1 TOP input to bare ends)
•
one (1) yoke with yoke installation hardware (the luminaire ships with the yoke attached)
•
one (1) stainless steel safety cable with locking carabiner
Visually inspect the shipping carton for damage that may have occurred during transit. If the
shipping carton shows signs of damage, document the damage fully before unpacking the
contents. Documentation of any damage is helpful when reporting a claim with the carrier.
The luminaire weighs approximately 38kg (84lb). For your safety, ETC recommends that two
people unpack the luminaire from the shipping carton. Use the handles on the sides of the
luminaire to lift the luminaire from the shipping carton.
Do not discard the shipping carton and packaging materials. The carton and packing materials
are specifically designed to protect the fixture during transport and will be useful if you need
to ship the fixture, including transporting the fixture for service.
Remove the Yoke
The Cyberlight LED ships with the yoke installed in a shipping configuration to help protect the
fixture from damage during transit. Remove the yoke from the fixture after you unpack the
fixture. See Yoke Assembly on page 8 for information about the components of the yoke.
Tool needed:
•
8.0mm hex key
1. Loosen but do not remove the yoke locking knobs on each side of the yoke.
2. Using the 8.0mm hex key, remove the yoke pivot screws and washers from each side of the
yoke.
Save the screws and washers. You will need them when you attach the yoke to the fixture
in its operating configuration.
3. Lift the yoke from the fixture.

7 Cyberlight LED User Manual
Fixture Overview
Item Description
1 Mirror head
2 Mirror
3 Output window
4 Handles
5 Adjustable yoke (see Yoke Assembly on the facing page for details)
6 Fans and dust filter
7 powerCON TRUE TOP power input and thru connectors
8 Display and navigation controls
9 USB port
10 Ethernet ports (x2)
11 DMX In and DMX Thru connectors

Specifications 8
Yoke Assembly
Item Description Quantity
1 Yoke 1
2 Yoke locking knob 2
3 8mm (5/16in) flat washer 2
4 8mm (5/16in) carriage bolt 2
5 Yoke pivot screw (M10x35mm) 2
6 Washer 2
7 Degree label 2
Specifications
For complete technical specifications, see the technical datasheet:
etcconnect.com/Products/High-End-Systems/Lighting-Fixtures/Cyberlight/Documentation.aspx
Environment
•
Ambient operating temperature range: -10°C to 40°C (14°F to 104°F).
•
Relative humidity: 0%–90%, non-condensing.
•
Storage temperature: -20°C to 60°C (0°F to 140°F).
•
Indoor use only.
•
Dry locations only, IP20 rated.

9 Cyberlight LED User Manual
Power
WARNING: Connect the fixture to a non-dimmable power source in order
to avoid damage to the fixture's internal power supply and other electrical
components. Using a dimmable power source can damage the fixture and
will void the warranty.
Electrical
•
100–240 VAC at 50/60 Hz
•
Maximum power consumption: 700W
Input and Power Factor
The values listed below were measured with LEDs at full and all motors functioning.
VAC Amps Hz Watts VA PF
100 7.0 50 694 697 0.99
120 5.7 60 681 687 0.99
200 3.3 50 661 666 0.99
208 3.2 60 661 666 0.99
220 3.0 50 661 669 0.99
230 2.9 50 656 661 0.99
240 2.8 60 659 667 0.98
Fixtures per Circuit
One fixture can be linked via the power thru connector (2 fixtures total per circuit).
The fixtures per circuit information assumes the use of an ETC R20 breaker module. Consult
the upstream breaker trip curves when using other equipment.
Connector Specification
WARNING: Risk of Shock and Fire. Assemble a grounding-type attachment
plug with integral cord grip that is within the voltage and amperage rating
of this luminaire.
AVERTISSEMENT : Risque de choc et d'incendie. Assurez-vous d'utiliser
une prise de mise à la terre avec décharge de traction intégrée qui respecte
la tension et l'ampérage de ce luminaire.
A power input cable with powerCON®TRUE1®TOP input to bare ends is provided. The power
input cable is rated for maximum 20A/120VAC and 16A/240VAC. Install a suitable
connector to meet the installation requirements. See the following wire color code chart:
Wire Color Code (EU) Wire Color Code (US Standard) Connection type Terminal
Green/Yellow Green Earth/Ground
Blue White Neutral N
Brown Black Line (Live) L

Fixture Installation Hardware 10
Fixture Installation Hardware
The top of the yoke has two 13 mm (1/2 in) diameter mounting holes for attaching installation
hardware. Installation hardware is not provided with the Cyberlight LED fixture. Select
appropriately sized hardware for your installation.
The installation hardware you choose must be capable of supporting, at a minimum, the
weight of the fixture (38kg [84lb]) and the associated cables.
Install the Yoke
The Cyberlight LED fixture yoke can be installed in two configurations:
•
The standard yoke installation is shown in (a) below.
-
The yoke pivot screws and washers are installed in the screw hole at the end of each
yoke arm.
-
The yoke locking knobs are installed in the star-shaped hole nearest the end of the each
yoke arm.
•
The optional installation (shown in (b) below) lets you suspend the fixture closer to the
installation point.
-
The yoke pivot screws and washers are installed in the screw hole in the center of each
yoke arm.
-
The yoke locking knobs are installed in the star-shaped hole nearest the top of the yoke.
Note: Due to limited space between the yoke and the fixture when the yoke is
installed in the optional configuration (b), ETC recommends that you attach the
installation hardware to the yoke before you attach the yoke to the fixture.
See Yoke Assembly on page8 for details about the yoke and its hardware.

11 Cyberlight LED User Manual
Tool needed:
•
8.0mm hex key
1. Insert the 8mm (5/16in) carriage bolts through the appropriate star-shaped holes in the
yoke, and attach the 8mm (5/16in) flat washers and yoke locking knobs to the bolts. Do
not tighten the knobs at this time; you will adjust them later.
2. Position the yoke on the fixture.
a. Make sure the U-shape of the yoke is located on the same side of the fixture as the back
side of the mirror head.
b. Align the appropriate screw holes in the yoke with the screw holes on the sides of the
fixture.
3. Using the 8.0mm hex key, attach the washers and yoke pivot screws to each side of the
yoke. Tighten the screws until the screws are securely fastened but you are still able to
pivot the yoke.
4. Rotate the yoke to the desired position. Use the markings on the degree label for precise
positioning.
5. Firmly tighten the yoke locking knobs to secure the yoke in place.
6. Firmly tighten the yoke pivot screws.

Install the Fixture 12
Install the Fixture
Overhead rigging must be performed by qualified personnel. Follow all local and national
codes and recommended practices.
WARNING:
•
The installation location must support a minimum point load of 6 times
the weight of the fixture.
•
The installation must always be secured with a secondary safety
attachment. An appropriate safety cable is supplied.
•
Safety cable attachment must be rated by a safety factor of 6.
•
A supportive and stable surface must be used when the fixtures are
placed on the feet.
•
Never stand directly below the installed fixture when mounting,
removing, or servicing the fixture.
•
All safety and technical aspects of fixture installation must be approved
by a qualified personnel before operation.
•
The installation must be regularly inspected by qualified personnel.
AVERTISSEMENT :
•
L'emplacement d'installation doit supporter une charge concentrée
minimale de 6 fois le poids de l'appareil.
•
L'installation doit toujours être sécurisée par une fixation de sécurité
auxiliaire. Un câble de sécurité approprié est fourni.
•
La fixation du câble de sécurité doit être classée avec un facteur de
sécurité de 6.
•
Une surface d'appui stable doit être utilisée quand les projecteurs sont
placés sur pieds.
•
Ne vous placez jamais directement sous le projecteur lors du montage, du
démontage ou de son entretien.
•
Tous les aspects techniques et de sécurité de l'installation du projecteur
doivent être approuvés par un personnel qualifié avant qu'il ne soit
utilisé.
•
L'installation doit être régulièrement inspectée par du personnel qualifié.

13 Cyberlight LED User Manual
You can install the fixture in any of the orientations shown below. ETC recommends that you
use three people to install each Cyberlight LED fixture: two people to hold the fixture while the
third person secures the fixture to the installation location.
1. If you have not already done so, attach the installation hardware to the top of the yoke
following the hardware manufacturer's assembly instructions.
2. Loop the provided safety cable around the top of the yoke and secure it to the trussing
system or other safe installation point. Follow local codes and recommended safety
standards for securing the fixture to the installation location.
3. Attach the fixture to the installation location following the installation hardware
manufacturer's instructions for a secure fit.
4. Inspect the installation prior to lifting the fixture overhead.

DMX Control 14
DMX Control
The Cyberlight LED fixture operates on standard DMX-512 control bus, controlled by a DMX
console. The fixture requires 40 channels of DMX-512.
Attach the fixture to the control bus using a two-core, shielded cable with a 5-pin XLR
connector (Belden 9729 is preferred).
The fixture includes two 5-pin XLR connectors, one for DMX Input and one for DMX Thru (for
use when daisy-chaining fixtures on the DMX control bus).
DMX Connector Pinout
Use the following standard pinout when preparing DMX cable with 5-pin XLR connectors. ETC
recommends using Belden 9729 or equivalent cable. (See the ETC cable cross database for
equivalent alternatives: etcconnect.com/Support/Cable-Cross-Database.aspx.) The second
data pair in the recommended cable type is not used, but is reserved future service.
DMX-512 Pinout
for Five-Pin XLR Pin Use
1
2
3
4
5
Push
1
2
3
4
5
1 Common (shield)
2 Data -
3 Data +
4 Not connected
5 Not connected
Connect DMXCables to Fixture
The following instructions are guidelines for connecting DMX to your fixture. Your installation
may vary.
1. Connect a DMX data cable to the DMX control source and the DMX In XLR receptacle on
the first fixture in the DMX data run.
2. Link the remaining fixtures in the data run by connecting a DMX data cable from the DMX
Thru connector on a fixture to the DMX In connector on the next fixture in the data run.
Note: A maximum of 32 DMX devices may be connected in any one DMX data run
when installed in a daisy-chain fashion.

15 Cyberlight LED User Manual
Terminate DMX
Use a DMX terminator or install a resistor on the last fixture of the DMXcontrol run to prevent
corruption (data reflection) of the digital control signal by electrical noise.
A DMXterminator is an XLR plug with a 120 Ωresistor connected between pins 2 and 3 that
can be installed into the DMX output receptacle of the last fixture in the DMX control run.
Contact your authorized dealer or ETC for ordering information (etcconnect.com/contactETC),
or purchase an XLR DMX terminator from the ETC Online Shop (shop.etcconnect.com).
Set the DMX Start Address
Give each fixture a unique DMX starting address so that the correct fixture responds to the
control signals. This DMX start address is the channel number from which the fixture starts to
“listen” to the digital control information sent out from the control source.
Modify the DMX start address on the user interface, which is located on the rear of the fixture.
See DMX Address on page 19 .
Example: The Cyberlight LED requires 40 channels of control. If you set the DMX
starting address of the first fixture to 1, you could set the second fixture to 41 (40+1),
the third to 81 (40+41), and so on.
DMX Channels
The current DMX channel map for the Cyberlight LED can be found on the ETC website:
etcconnect.com/Products/High-End-Systems/Lighting-Fixtures/Cyberlight/Documentation.aspx