ETC Desire Fresnel User manual

Desire Fresnel
User Manual
Version 1.0.0
Part Number: 7419M1200-1.0.0 Rev: A
Released: 2021-04

To view a list of ETCtrademarks and patents, go to etcconnect.com/ip. All other trademarks, both marked
and not marked, are the property of their respective owners.
ETC intends this document, whether printed or electronic, to be provided in its entirety.

Table of Contents
Table of Contents i
Introduction 1
Help from ETC Technical Services 2
Safety 3
Overview 5
Fixture 5
User Interface 6
Set Up and Focus the Fixture 7
Mount the Fixture 7
Add Accessories 7
Connect Power and Data 8
Focus the Fixture 8
Use Fixture in DMX Mode 9
Set DMXAddress 10
Set DMXMode 10
Set DMX Loss Behavior 12
Use Fixture in Stand-aloneMode 13
Studio Mode 14
Color Mode 15
Effects Mode 16
Preset Mode 17
Set Up Wireless Control 18
Set Up Multiverse Wireless Communication 18
Configure Fixtures Wirelessly Using the Set LightApp 18

Control and Customize the Display 19
Lock the Display 19
Adjust the Display Settings 19
Troubleshooting and Maintenance 20
Troubleshooting Checklist 20
Adjust the Pulse Width Modulation (PWM) 21
Test the Emitters 21
View Diagnostic Data 22
Export Fixture Data for Troubleshooting 22
Restore Default Settings 23
Update Firmware 23
Backup and Restore the Fixture Configuration 24
Clean the Lens 24
Specifications and Reference 25
Environment 25
Dimensions and Weight 25
Electrical 25
RDM Parameters 25
Fixture Compliance 26
Wireless Radio Compliance 26
Licensed Software 26
ii Desire Fresnel User Manual

Introduction 1
Introduction
Desire Fresnel takes the best features of a standard incandescent Fresnel and adds in the
nuanced color mixing, smooth fades, and LED technology of ETC’s other professional-grade
fixtures. With a 13–55 degree zoom and expert color mixing, you get the feature set and
brightness you need. With the addition of deep red LEDs, the Lustr X8 array pushes the
boundaries of color rendering possibilities. Desire Fresnel is made in the USA and backed by a
24/7/365 phone support guarantee.

2 Desire Fresnel User Manual
Help from ETC Technical Services
If you are having difficulties and your problem is not addressed by this document, try the ETC
support website at support.etcconnect.com or the main ETC website at etcconnect.com. If none
of these resources are sufficient, contact ETC Technical Services directly at one of the offices
identified below. Emergency service is available from all ETC offices outside of normal business
hours.
When calling for help, take these steps first:
•
Prepare a detailed description of the problem
•
Go near the equipment for troubleshooting
•
Find your notification number if you have called in previously
ETC, Inc.
Americas
Technical Services Department
3031 Pleasant View Road
Middleton, WI 53562
800-775-4382 (USA, toll-free)
[phone]
[e-mail]
ETC GmbH
Germany, Austria, Switzerland,
Eastern Europe, and Russia
Technical Services Department
Ohmstrasse 3
83607 Holzkirchen, Germany
[phone]
[e-mail]
ETC Austin
High End Systems Products
Technical Services Department
2105 Gracy Farms Lane
Austin, TX 78758 USA
800-890-8989 (USA, toll-free)
[phone]
[e-mail]
ETC France
France
Zone Urbaparc -
Bâtiment E
6 Boulevard de la Libération
Saint-Denis, 93200
[phone]
[e-mail]
ETC Ltd
Europe, Middle East, and Africa
Technical Services Department
26-28 Victoria Industrial Estate
Victoria Road,
London W3 6UU England
[phone]
[e-mail]
ETCAsia
Asia
Technical Services Department
Room 1801, 18/F
Tower 1, Phase 1 Enterprise Square
9 Sheung Yuet Road
Kowloon Bay, Kowloon, Hong Kong
[phone]
[e-mail]

Introduction 3
Safety
WARNING: RISK OF ELECTRIC SHOCK! The light source in this luminaire is
not user-replaceable, and must be replaced only by a qualified technician.
Contact ETC Customer Support for assistance.
AVERTISSEMENT : RISQUE DE DÉCHARGE ÉLÉCTRIQUE! La source
lumineuse de ce projecteur n'est pas remplaçable par l'utilisateur et ne doit
être remplacée seulement par un technicien qualifié. Contactez le service
client ETC pour obtenir de l’assistance.
WARNING: Note the following safety warnings before use:
•
Use the fixture in dry locations only, where humidity does not exceed
90 percent (non-condensing).
•
Connect the fixture to a non-dimmable power source in order to avoid
damage to the fixture's internal power supply and other electrical
components. Using a dimmable power source can damage the fixture
and will void the warranty.
•
Disconnect the fixture from power and DMX and allow it to cool before
installing accessories or performing any cleaning and maintenance.
•
Only use mounting hardware that is rated for the total weight of the
fixture and accessories.
•
In addition to primary suspension, attach a safety cable (or other
approved safety device) to the fixture. Safety cables must be rated to
support ten times the fixture weight. Consult local standards to ensure
that safety cables meet all requirements.
•
Check that the accessory holder is locked and that any accessory safety
cables are connected before mounting the fixture.
•
Do not operate the fixture without the lens installed.
•
Do not use this fixture with a damaged power lead. If the power lead
(cord set) is damaged, it must be replaced.
•
Do not use this fixture if the lens is deeply scratched or cracked. You
must replace the lens when it is damaged.

4 Desire Fresnel User Manual
AVERTISSEMENT : Prendre connaissance des avertissements de sécurité
suivants avant toute utilisation :
•
Débranchez le projecteur de son alimentation et du DMX et laissez-le
refroidir avant d’installer des accessoires ou d’effectuer un nettoyage
ou un entretien.
•
N’utilisez que de la quincaillerie de montage adaptée au poids total
des projecteurs et des accessoires.
•
En plus de la suspension principale, fixez une chaîne de sécurité (ou
tout autre dispositif de sécurité homologué) au projecteur. Les chaînes
de sécurité doivent être en mesure de supporter dix fois le poids du
projecteur. Consultez les normes locales pour vous assurer que les
câbles de sécurité respectent toutes les exigences.
•
Vérifiez que le porte-accessoires est verrouillé et que les élingues de
tous les accessoires sont bien attachées avant de monter le projecteur.
•
Ne pas utiliser ce projecteur avec un cordon d’alimentation
endommagé. Si le cordon d’alimentation (câble) est abîmé, il doit être
remplacé.
The luminaire must be installed at least 0.1m (4.0in)
away from all lighted objects.
Le luminaire doit être installé à au moins 0,1m (4,0po)
de tout objet éclairé.
Risk of electric shock Risque de décharge éléctrique
This product should not be discarded as unsorted
waste but must be sent to separate collection facilities
for recovery and recycling.
Ce produit ne doit pas être jeté avec les déchets
ménagers mais doit être déposé dans une collecte de
déchets électroniques ou dans un point de collecte.

Overview 5
Overview
Fixture
A
D
G
F
E
I
J
H
A
B
D
C
AAccessory holder: Insert accessories into the two available slots from either side of the holder,
and then lock the holder. See Add Accessories on page7 .
BYoke tilt-lock: Tilt the fixture as needed, and then turn the tilt-lock clockwise to lock the
position. If necessary, pull the tilt-lock away from the stem to adjust the tilt-lock position.
CAdjustable yoke: Loosen the bolts, and then shift the adjustable yoke forward or backward as
needed to balance the fixture. Tighten the bolts to secure. See Add Accessories on page7 .
DZoom knob: Rotate the zoom knob on either side of the fixture to adjust from spot to flood.
ENFC(Near Field Communication) tag: Use the Set Light app to wirelessly configure the fixture,
with or without power applied to the fixture. See
Set Up Wireless Control on page18
.
FUser interface: View the fixture status, set the DMXaddress and mode, or set stand-alone
options.
GAntenna: For use when controlling the fixture using wireless DMX. See Set Up Wireless Control
on page18
.
HSafety cable attachment point: See Mount the Fixture on page7 .
IDMX In and DMX Thru connectors: Five-pin XLRconnectors for DMX/RDM in and thru.
JPower In and Power Thru connectors: powerCON®TRUE1 TOP connectors for power in and
thru.

6 Desire Fresnel User Manual
User Interface
DMX
Address
Mode
DMX Loss
1/3 Red
001
3 Ch RGB
HLL 2 Min
B
A
E
F
G
C
D
ADisplay: The colors of options on the display correspond to the colors of the encoders below the
display (E) and the Intensity encoder to the right of the display(B).
BIntensity encoder:
•
When in DMX mode, press the Intensity encoder to enter Focus mode when focusing the
fixture.
•
When configuring the fixture in one of the stand-alone modes, press the Intensity encoder to
toggle between the current intensity and 0, or turn the Intensity encoder to modify the white
fields on the display. See Use Fixture in Stand-aloneMode on page13 .
•
When navigating from the Main Menu screen, turn the Intensity encoder to scroll through
menu options, and then press the Intensity encoder to select a menu option.
CMenu button: Press to view the Main Menu screen and configure the fixture. Press the button
again to return to the previous screen when you are setting configuration options.
DFunction button: Press the button, use the Intensity encoder to navigate to one of the following
modes, and then press the Intensity encoder to select it:
•
DMX:View and set DMX parameters for the fixture.
•
Studio: Use one of three studio (white light) presets, or customize the presets.
•
Color: Use one of 12 color presets, or customize the presets.
•
Effects:Use a sequence, or customize a sequence.
•
Preset: Use one of 12 presets (color preset + fade time), or customize the presets.
See Use Fixture in Stand-aloneMode on page13 and Use Fixture in DMX Mode on page9 .
EEncoders(Red, Green, Blue):The colors of encoders correspond to options on the display.
Press to activate the options at the bottom of the display, or turn to modify the values on the
display.
FUSB port: Use for updating firmware, saving and loading fixture configuration settings, or
saving error logs via a flash drive. See Troubleshooting and Maintenance on page20
.
GUI lock: Set this switch to lock the UI. This prevents inadvertent changes to the UI. See Lock the
Display on page19
.