ETC HIGH END SYSTEMS LONESTAR User manual

High End Systems
Lonestar
Automated Luminaire User Manual
Version 1.3.0
Part Number: 2550M1200-1.3.0 Rev: A
Released: 2021-08

To view a list of ETCtrademarks and patents, go to etcconnect.com/ip. All other trademarks, both marked
and not marked, are the property of their respective owners.
You can find complete High End Systems terms and conditions and warranty information at
etcconnect.com/Support/Warranty.aspx.
ETC intends this document, whether printed or electronic, to be provided in its entirety.

Table of Contents
Table of Contents i
Introduction 1
Important Safety Information 1
Help from Technical Services 2
Safety Considerations 3
General Operation and Use Guidelines 5
Fixture Overview 6
Install the Fixture 7
Power 10
Electrical Specifications 10
Input and Power Factor 10
Fixtures per Circuit 10
Connector Specification 11
DMX Control 12
DMX Connector Pinout 12
Connect DMXCables to Fixture 12
DMX Control and Ethernet Output 13
Terminate DMX 13
Set the DMX Start Address 13
DMX Channels 13

Ethernet Control 14
Connect EthernetCables to a Fixture 14
Ethernet Control and DMX Thru 15
Terminate DMX 15
Set the DMX Start Address 15
Set the Control Input and Universe 15
Configure the Fixture 16
Navigate the User Interface 16
Set Fixture Parameters 17
DMX Address 17
Info Menu 17
Set Menu 18
Test Menu 22
Preset Menu 22
Install the Heavy Diffusion Accessory 23
Error Codes 26
Maintenance 29
Clean the Fixture 29
Replace the Fuse 29
Compliance 29
ii Lonestar User Manual

Introduction 1
Introduction
Congratulations on your purchase of the Lonestar automated framing fixture. This manual
provides important information for the safe installation, configuration, and maintenance of your
Lonestar fixture.
Important Safety Information
Please read all instructions prior to assembling, mounting, and operating this equipment.
Continued and safe operation of this fixture is the responsibility of the operator. This manual will
give tips for that continued safe operation. At any time please contact Technical Services for any
safety concerns.
The following international note, caution, and warning symbols appear in margins throughout
this manual to highlight important messages.
Note: Notes are helpful hints and information that is supplemental to the main text.
CAUTION: Hot Surfaces. This statement indicates that while operating,
equipment surfaces may reach very high temperatures. Allow the fixture
to cool before handling or servicing.
CAUTION: A Caution statement indicates situations where there may be
undefined or unwanted consequences of an action, potential for data loss or
an equipment problem.
WARNING: A Warning statement indicates situations where damage may
occur, people may be harmed, or there are serious or dangerous
consequences of an action
WARNING: RISK OF ELECTRIC SHOCK! This warning statement indicates
situations where there is a risk of electric shock.
All ETC High End Systems documents are available for free download from our website:
etcconnect.com/Products/High-End-Systems.
Please email comments about this manual to: [e-mail].

2 Lonestar User Manual
Help from Technical Services
If you are having difficulties and your problem is not addressed by this document, try the ETC
support website at support.etcconnect.com or the High End Systems product website at
etcconnect.com/Products/High-End-Systems. If none of these resources are sufficient, contact
ETC Technical Services directly at one of the offices identified below. Emergency service is
available from all offices outside of normal business hours.
When calling for help, take these steps first:
lPrepare a detailed description of the problem
lGo near the equipment for troubleshooting
lFind your notification number if you have called in previously
ETC, Inc.
Americas
Technical Services Department
3031 Pleasant View Road
Middleton, WI 53562
800-775-4382 (USA, toll-free)
[phone]
[e-mail]
ETC GmbH
Germany, Austria, Switzerland,
Eastern Europe, and Russia
Technical Services Department
Ohmstrasse 3
83607 Holzkirchen, Germany
[phone]
[e-mail]
ETC Austin
High End Systems Products
Technical Services Department
2105 Gracy Farms Lane
Austin, TX 78758 USA
800-890-8989 (USA, toll-free)
[phone]
[e-mail]
ETC France
France
Zone Urbaparc -
Bâtiment E
6 Boulevard de la Libération
Saint-Denis, 93200
[phone]
[e-mail]
ETC Ltd
Europe, Middle East, and Africa
Technical Services Department
26-28 Victoria Industrial Estate
Victoria Road,
London W3 6UU England
[phone]
[e-mail]
ETCAsia
Asia
Technical Services Department
Room 1801, 18/F
Tower 1, Phase 1 Enterprise Square
9 Sheung Yuet Road
Kowloon Bay, Kowloon, Hong Kong
[phone]
[e-mail]

Safety Considerations 3
Safety Considerations
To ensure safe operation, follow the safety instructions and warning notes in this user manual.
lThe Lonestar is intended for professional use only. Not for residential use. Read the entire
manual before using this equipment.
lContact your ETC authorized dealer or Technical Services before performing any service in
order to maintain warranty coverage.
Symbols used on the product label are defined below:
3.0 m
The luminaire must be installed at least 3.0m (9ft
10in) away from all lighted objects.
Le luminaire doit être installé à au moins 3,0m (9pi.
10po.) de tout objet éclairé.
General warning Avertissement général
Do not stare at the operating light source. Ne pas regarder la source de lumière lorsqu’elle
fonctionne.
This product should not be discarded as unsorted
waste but must be sent to separate collection
facilities for recovery and recycling.
Ce produit ne doit pas être jeté avec les déchets
ménagers mais doit être déposé dans une collecte de
déchets électroniques ou dans un point de collecte.
taor TaRated maximum ambient temperature Température ambiante maximale recommandée
tcor TcRated maximum case temperature Température maximale recommandée pour le boîtier
Operate indoors only, not where this product
would be exposed to the weather.
Ne fonctionne qu'à l'intérieur, pas là où ce produit
serait exposé aux intempéries.
WARNING: Note the following safety warnings before use:
lThis equipment is designed for operation by qualified personnel only.
lReplace fuses with the specified type and rating only. See page 29 .
lMake sure that the available voltage is within the stated range. See
page 10 .
lDo not use this fixture with a damaged power lead (cord set). If the lead
is damaged, it must be replaced by a qualified technician with an
equivalent type before use. Contact your local authorized dealer for
spare power leads.
lDo not use this fixture if the lens is damaged. Damaged lenses must be
replaced before use. Contact your local authorized dealer for a
replacement.
lDo not mount the fixture on or near flammable surfaces.
lMinimum distance from fixture head to combustible materials:
0.1 m (4 in).
lMinimum distance to lighted objects:3.0 m (9 ft 10 in).

4 Lonestar User Manual
AVERTISSEMENT : Pour votre sécurité, lisez les mises en garde et les avis
suivants avant toute utilisation :
lCet équipement est conçu pour être utilisé par un personnel qualifié
uniquement.
lRemplacez les fusibles uniquement par le type et le calibre indiqués.
Voir page 29 .
lVeillez à ce que la tension disponible soit dans la plage indiquée.Voir
page 10 .
lN'utilisez pas ce projecteur avec un cordon d'alimentation endommagé
(fils électriques). Si le cordon est endommagé, un technicien qualifié
doit le remplacer par un cordon de type équivalent avant que l'appareil
ne puisse être utilisé. Contactez votre distributeur agréé local pour
obtenir des cordons d'alimentation de rechange.
lN'utilisez pas cet appareil si la lentille est endommagée. Les lentilles
endommagées doivent être remplacées avant l'utilisation. Contactez
votre revendeur agréé local pour un remplacement.
lNe pas installer le projecteur sur ou à côté d’une surface inflammable.
lDistance minimum entre la tête du luminaire et les matériaux
combustibles : 0.1 m (4 in).
lDistance minimale avec les objets éclairés :3.0 m (9 ft 10 in).
WARNING: RISK OF ELECTRIC SHOCK!
lDo not operate this device with the cover open.
lDisconnect the fixture from power and DMX and allow it to cool before
performing any cleaning and maintenance.
AVERTISSEMENT : RISQUE DE CHOC ÉLÉCTRIQUE!
lN'utilisez pas cet appareil avec le couvercle ouvert.
lDébrancher la lampe de son alimentation et du DMX et la laisser
refroidir avant d’effectuer un nettoyage ou un entretien.
RISK GROUP 2: CAUTION. Possibly hazardous optical radiation emitted
from this product. Do not stare at operating lamp. May be harmful to the
eyes.
GROUPE DE RISQUE 2 (RISQUE MODÉRÉ) : ATTENTION. Rayonnement
optique potentiellement dangereux émis par ce produit. Ne regardez pas la
lampe en fonctionnement. Peut être nocif pour les yeux.
CAUTION: Hot Surfaces. Allow the device to cool completely before
handling and servicing.
ATTENTION : Surfaces chaudes. Laissez le luminaire refroidir complètement
avant de le manipuler et de procéder à son entretien.
Note: The light source in this luminaire is not user-replaceable, and must be replaced
only by a qualified technician. Contact ETC Customer Support for assistance.

Safety Considerations 5
General Operation and Use Guidelines
lThis fixture is only allowed to be operated with the maximum alternating current that is
stated in the technical specifications label provided on the fixture.
lLighting effects are not designed for permanent operation. Consistent operation breaks may
extend the life of the fixture.
lWhen choosing the installation location, make sure the fixture will not be exposed to
extreme heat, moisture, or dust.
lDo not point the lens toward the sun or other bright light source. Doing so could damage the
fixture.
lIf using the supplied Omega brackets with quick-locking thumb screws for fixture hanging,
ensure that the thumb screws have engaged a complete 90-degree positive latch.
lOperate the fixture only after having familiarized yourself with its functions. Do not permit
persons who are not qualified and familiar with its functions to operate the fixture.
lDo not modify the fixture. Any modifications will void the warranty.
lThis manual describes the proper installation and operation of this fixture. Using this fixture
in any way other than the intended use may cause damage and void the warranty.
lWhen the fixture has been stored or transported in cold temperatures, allow it to warm to
room temperature for a minimum of one hour before applying power. Applying power to a
cold fixture may cause damage to the fixture and void the manufacturer warranty.
lWhen you power on the fixture, you may notice smoke or odor. This is normal and should
decrease gradually. If smoke or odor persists, disconnect the fixture from power and contact
your ETC dealer or Technical Services.
lPlease use the original packaging if the fixture is to be transported. ETC will not be
responsible for the fixture if packaging other than manufacturer provided packaging is used.

6 Lonestar User Manual
Fixture Overview
For complete technical specifications of the Lonestar fixture, see the technical datasheet:
etcconnect.com/Products/High-End-Systems/Lighting-Fixtures/Lonestar/Documentation.aspx
1: Lens
2: Tilt lock
3: Yoke handle
4: Display
5: Navigation controls
6: Pan lock
7: Handle
8: Ethernet ports (x2)
9: DMX Thru
10: DMX In
11: Power In
12: USB
13: Power Out